- 您現在的位置：買賣IC網 > PDF目錄385520 > MAX1082 (Maxim Integrated Products, Inc.) 300ksps/400ksps, Single-Supply, 4-Channel, Serial 10-Bit ADCs with Internal Reference PDF資料下載
參數資料
| 型號： | MAX1082 |
| 廠商： | Maxim Integrated Products, Inc. |
| 英文描述： | 300ksps/400ksps, Single-Supply, 4-Channel, Serial 10-Bit ADCs with Internal Reference |
| 中文描述： | 300ksps/400ksps、單電源、4通道、串行10位ADC，內置電壓基準 |
| 文件頁數： | 12/24頁 |
| 文件大?。?/td> | 315K |
| 代理商： | MAX1082 |
M
300ksps/400ksps, Single-Supply, 4-Channel,
Serial 10-Bit ADCs with Internal Reference
12
______________________________________________________________________________________
Track/Hold
The T/H enters its tracking mode on the falling clock
edge after the fifth bit of the 8-bit control word has been
shifted in. It enters its hold mode on the falling clock
edge after the eighth bit of the control word has been
shifted in. If the converter is set up for single-ended
inputs, IN- is connected to COM and the converter
samples the “+” input. If the converter is set up for dif-
ferential inputs, the difference of
[(
IN+) - (IN-)
]
is con-
verted. At the end of the conversion, the positive input
connects back to IN+ and C
HOLD
charges to the input
signal.
The time required for the T/H to acquire an input signal
is a function of how quickly its input capacitance is
charged. If the input signal’s source impedance is high,
the acquisition time lengthens, and more time must be
allowed between conversions. The acquisition time,
t
ACQ
, is the maximum time the device takes to acquire
the signal and the minimum time needed for the signal
to be acquired. It is calculated by the following equa-
tion:
t
ACQ
= 7 x (R
S
+ R
IN
) x 18pF
where R
IN
= 800
, R
S
= the source impedance of the
input signal, and t
ACQ
is never less than 400ns
(MAX1082) or 625ns (MAX1083). Note that source
impedances below 4k
do not significantly affect the
ADC’s AC performance.
Input Bandwidth
The ADC’s input tracking circuitry has a 6MHz
(MAX1082) or 3MHz (MAX1083) small-signal band-
width, so it is possible to digitize high-speed transient
events and measure periodic signals with bandwidths
exceeding the ADC’s sampling rate by using under-
sampling techniques. To avoid high-frequency signals
being aliased into the frequency band of interest, anti-
alias filtering is recommended.
Analog Input Protection
Internal protection diodes, which clamp the analog input
to V
DD1
and GND, allow the channel input pins to swing
from GND - 0.3V to V
DD1
+ 0.3V without damage.
However, for accurate conversions near full scale, the
inputs must not exceed V
DD1
by more than 50mV or be
lower than GND by 50mV.
If the analog input exceeds 50mV beyond the sup-
plies, do not allow the input current to exceed 2mA.
How to Start a Conversion
Start a conversion by clocking a control byte into DIN.
With
CS
low, each rising edge on SCLK clocks a bit from
DIN into the MAX1082/MAX1083’s internal shift register.
After
CS
falls, the first arriving logic “1” bit defines the
control byte’s MSB. Until this first “start” bit arrives, any
number of logic “0” bits can be clocked into DIN with no
effect. Table 3 shows the control-byte format.
The MAX1082/MAX1083 are compatible with SPI/
QSPI and MICROWIRE devices. For SPI, select the cor-
rect clock polarity and sampling edge in the SPI control
registers: set CPOL = 0 and CPHA = 0. MICROWIRE,
SPI, and QSPI all transmit a byte and receive a byte at
the same time. Using the
Typical Operating Circuit
, the
simplest software interface requires only three 8-bit
transfers to perform a conversion (one 8-bit transfer to
configure the ADC, and two more 8-bit transfers to clock
out the conversion result). See Figure 16 for MAX1082/
MAX1083 QSPI connections.
Simple Software Interface
Make sure the CPU’s serial interface runs in master
mode so the CPU generates the serial clock. Choose a
clock frequency from 500kHz to 6.4MHz (MAX1082) or
4.8MHz (MAX1083).
1) Set up the control byte and call it TB1. TB1 should
be of the format: 1XXXXXXX binary, where the Xs
denote the particular channel, selected conversion
mode, and power mode.
2) Use a general-purpose I/O line on the CPU to pull
CS
low.
3) Transmit TB1 and, simultaneously, receive a byte
and call it RB1. Ignore RB1.
4) Transmit a byte of all zeros ($00 hex) and, simulta-
neously, receive byte RB2.
5) Transmit a byte of all zeros ($00 hex) and, simulta-
neously, receive byte RB3.
6) Pull
CS
high.
Figure 5 shows the timing for this sequence. Bytes RB2
and RB3 contain the result of the conversion, padded
with three leading zeros, two sub-LSB bits, and one
trailing zero. The total conversion time is a function of
the serial-clock frequency and the amount of idle time
between 8-bit transfers. To avoid excessive T/H droop,
make sure the total conversion time does not exceed
120μs.
Digital Output
In unipolar input mode, the output is straight binary
(Figure 13). For bipolar input mode, the output is two’s
complement (Figure 14). Data is clocked out on the ris-
ing edge of SCLK in MSB-first format.
相關PDF資料 |
PDF描述 |
|---|---|
| MAX1082-MAX1083 | 300ksps/400ksps, Single-Supply, 4-Channel, Serial 10-Bit ADCs with Internal Reference |
| MAX1082ACUE | 300ksps/400ksps, Single-Supply, 4-Channel, Serial 10-Bit ADCs with Internal Reference |
| MAX1082AEUE | 300ksps/400ksps, Single-Supply, 4-Channel, Serial 10-Bit ADCs with Internal Reference |
| MAX1082BCUE | 300ksps/400ksps, Single-Supply, 4-Channel, Serial 10-Bit ADCs with Internal Reference |
| MAX1082BEUE | 300ksps/400ksps, Single-Supply, 4-Channel, Serial 10-Bit ADCs with Internal Reference |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MAX1082_12 | 制造商:MAXIM 制造商全稱:Maxim Integrated Products 功能描述:300ksps/400ksps, Single-Supply, 4-Channel, Serial 10-Bit ADCs with Internal Reference |
| MAX1082ACUE | 功能描述:模數轉換器 - ADC RoHS:否 制造商:Texas Instruments 通道數量:2 結構:Sigma-Delta 轉換速率:125 SPs to 8 KSPs 分辨率:24 bit 輸入類型:Differential 信噪比:107 dB 接口類型:SPI 工作電源電壓:1.7 V to 3.6 V, 2.7 V to 5.25 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:VQFN-32 |
| MAX1082ACUE+ | 功能描述:模數轉換器 - ADC 300/400ksps Sgl-Sply 4Ch Serial 10Bit RoHS:否 制造商:Texas Instruments 通道數量:2 結構:Sigma-Delta 轉換速率:125 SPs to 8 KSPs 分辨率:24 bit 輸入類型:Differential 信噪比:107 dB 接口類型:SPI 工作電源電壓:1.7 V to 3.6 V, 2.7 V to 5.25 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:VQFN-32 |
| MAX1082ACUE+T | 功能描述:模數轉換器 - ADC 300/400ksps Sgl-Sply 4Ch Serial 10Bit RoHS:否 制造商:Texas Instruments 通道數量:2 結構:Sigma-Delta 轉換速率:125 SPs to 8 KSPs 分辨率:24 bit 輸入類型:Differential 信噪比:107 dB 接口類型:SPI 工作電源電壓:1.7 V to 3.6 V, 2.7 V to 5.25 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:VQFN-32 |
| MAX1082ACUE-T | 功能描述:模數轉換器 - ADC RoHS:否 制造商:Texas Instruments 通道數量:2 結構:Sigma-Delta 轉換速率:125 SPs to 8 KSPs 分辨率:24 bit 輸入類型:Differential 信噪比:107 dB 接口類型:SPI 工作電源電壓:1.7 V to 3.6 V, 2.7 V to 5.25 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:VQFN-32 |
發布緊急采購，3分鐘左右您將得到回復。