- 您現在的位置：買賣IC網 > PDF目錄384647 > MAX1080BCUP (MAXIM INTEGRATED PRODUCTS INC) 300ksps/400ksps, Single-Supply, Low-Power, 8-Channel, Serial 10-Bit ADCs with Internal Reference PDF資料下載
參數資料
| 型號： | MAX1080BCUP |
| 廠商： | MAXIM INTEGRATED PRODUCTS INC |
| 元件分類： | ADC |
| 英文描述： | 300ksps/400ksps, Single-Supply, Low-Power, 8-Channel, Serial 10-Bit ADCs with Internal Reference |
| 中文描述： | 8-CH 10-BIT SUCCESSIVE APPROXIMATION ADC, SERIAL ACCESS, PDSO20 |
| 封裝： | 4.40 MM, 0.65 MM PITCH, MO-153AD, TSSOP-20 |
| 文件頁數： | 14/24頁 |
| 文件大?。?/td> | 550K |
| 代理商： | MAX1080BCUP |
M
Figure 6 shows the timing for this sequence. Bytes RB2
and RB3 contain the result of the conversion, padded
with three leading zeros, two sub-LSB bits, and one
trailing zero. The total conversion time is a function of
the serial-clock frequency and the amount of idle time
between 8-bit transfers. To avoid excessive T/H droop,
make sure the total conversion time does not exceed
120μs.
Digital Output
In unipolar input mode, the output is straight binary
(Figure 14). For bipolar input mode, the output is two’s
complement (Figure 15). Data is clocked out on the ris-
ing edge of SCLK in MSB-first format.
Serial Clock
The external clock not only shifts data in and out but
also drives the analog-to-digital conversion steps.
SSTRB pulses high for one clock period after the last bit
of the control byte. Successive-approximation bit deci-
sions are made and appear at DOUT on each of the
next 12 SCLK rising edges (Figure 6). SSTRB and
DOUT go into a high-impedance state when
CS
goes
high; after the next
CS
falling edge, SSTRB outputs a
logic low. Figure 7 shows the detailed serial-interface
timings.
The conversion must complete in 120μs or less, or
droop on the sample-and-hold capacitors may degrade
conversion results.
Data Framing
The falling edge of
CS
does
not
start a conversion.
The first logic high clocked into DIN is interpreted as a
start bit and defines the first bit of the control byte. A
conversion starts on SCLK’s falling edge, after the eighth
bit of the control byte (the PD0 bit) is clocked into DIN.
The start bit is defined as follows:
The first high bit clocked into DIN with
CS
low any
time the converter is idle, e.g., after V
DD1
and V
DD2
are applied.
OR
The first high bit clocked into DIN after bit 4 of a con-
version in progress is clocked onto the DOUT pin.
Once a start bit has been recognized, the current conver-
sion may only be terminated by pulling
SHDN
low.
The fastest the MAX1080/MAX1081 can run with
CS
held
low between conversions is 16 clocks per conversion.
Figure 8 shows the serial-interface timing necessary to
perform a conversion every 16 SCLK cycles. If
CS
is tied
low and SCLK is continuous, guarantee a start bit by first
clocking in 16 zeros.
300ksps/400ksps, Single-Supply, Low-Power,
8-Channel, Serial 10-Bit ADCs with Internal Reference
14
______________________________________________________________________________________
BIT
NAME
DESCRIPTION
7(MSB)
START
The first logic “1” bit after
CS
goes low defines the beginning of the control byte.
6
5
4
SEL2
SEL1
SEL0
These three bits select which of the eight channels are used for the conversion (Tables 1 and 2).
3
UNI/BIP
1 = unipolar, 0 = bipolar. Selects unipolar or bipolar conversion mode. In unipolar mode, an
analog input signal from 0 to V
REF
can be converted; in bipolar mode, the differential signal can
range from -V
REF
/2 to +V
REF
/2.
2
SGL/DIF
1 = single ended, 0 = pseudo-differential. Selects single-ended or pseudo-differential conver-
sions. In single-ended mode, input signal voltages are referred to COM. In pseudo-differential
mode, the voltage difference between two channels is measured (Tables 1 and 2).
1
0(LSB)
PD1
PD0
Select operating mode.
PD1
PD0
0
0
0
1
1
0
1
1
Mode
Full power-down
Fast power-down
Reduced power
Normal operation
Table 3. Control-Byte Format
BIT 7
BIT 6
(MSB)
BIT 5
BIT 4
BIT 3
BIT 2
BIT 1
BIT 0
(LSB)
START
SEL2
SEL1
SEL0
UNI/BIP
SGL/DIF
PD1
PD0
相關PDF資料 |
PDF描述 |
|---|---|
| MAX1080BEUP | 300ksps/400ksps, Single-Supply, Low-Power, 8-Channel, Serial 10-Bit ADCs with Internal Reference |
| MAX1081ACUP | 300ksps/400ksps, Single-Supply, Low-Power, 8-Channel, Serial 10-Bit ADCs with Internal Reference |
| MAX1081AEUP | 300ksps/400ksps, Single-Supply, Low-Power, 8-Channel, Serial 10-Bit ADCs with Internal Reference |
| MAX1081BCUP | 300ksps/400ksps, Single-Supply, Low-Power, 8-Channel, Serial 10-Bit ADCs with Internal Reference |
| MAX1081BEUP | 300ksps/400ksps, Single-Supply, Low-Power, 8-Channel, Serial 10-Bit ADCs with Internal Reference |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MAX1080BCUP+ | 功能描述:模數轉換器 - ADC 5V 400ksps Low-Power 8Ch Serial 10-Bit RoHS:否 制造商:Texas Instruments 通道數量:2 結構:Sigma-Delta 轉換速率:125 SPs to 8 KSPs 分辨率:24 bit 輸入類型:Differential 信噪比:107 dB 接口類型:SPI 工作電源電壓:1.7 V to 3.6 V, 2.7 V to 5.25 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:VQFN-32 |
| MAX1080BCUP+T | 功能描述:模數轉換器 - ADC 5V 400ksps Low-Power 8Ch Serial 10-Bit RoHS:否 制造商:Texas Instruments 通道數量:2 結構:Sigma-Delta 轉換速率:125 SPs to 8 KSPs 分辨率:24 bit 輸入類型:Differential 信噪比:107 dB 接口類型:SPI 工作電源電壓:1.7 V to 3.6 V, 2.7 V to 5.25 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:VQFN-32 |
| MAX1080BCUP-T | 功能描述:模數轉換器 - ADC RoHS:否 制造商:Texas Instruments 通道數量:2 結構:Sigma-Delta 轉換速率:125 SPs to 8 KSPs 分辨率:24 bit 輸入類型:Differential 信噪比:107 dB 接口類型:SPI 工作電源電壓:1.7 V to 3.6 V, 2.7 V to 5.25 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:VQFN-32 |
| MAX1080BEUP | 功能描述:模數轉換器 - ADC RoHS:否 制造商:Texas Instruments 通道數量:2 結構:Sigma-Delta 轉換速率:125 SPs to 8 KSPs 分辨率:24 bit 輸入類型:Differential 信噪比:107 dB 接口類型:SPI 工作電源電壓:1.7 V to 3.6 V, 2.7 V to 5.25 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:VQFN-32 |
| MAX1080BEUP+ | 功能描述:模數轉換器 - ADC 5V 400ksps Low-Power 8Ch Serial 10-Bit RoHS:否 制造商:Texas Instruments 通道數量:2 結構:Sigma-Delta 轉換速率:125 SPs to 8 KSPs 分辨率:24 bit 輸入類型:Differential 信噪比:107 dB 接口類型:SPI 工作電源電壓:1.7 V to 3.6 V, 2.7 V to 5.25 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:VQFN-32 |
發布緊急采購，3分鐘左右您將得到回復。