- 您現在的位置：買賣IC網 > PDF目錄383308 > MAX1062 (Maxim Integrated Products, Inc.) 14-Bit, %V, 200ksps ADC with 10レA Shutdown PDF資料下載
參數資料
| 型號： | MAX1062 |
| 廠商： | Maxim Integrated Products, Inc. |
| 英文描述： | 14-Bit, %V, 200ksps ADC with 10レA Shutdown |
| 中文描述： | 14位、+5V、200ksps ADC，帶有10µA關斷 |
| 文件頁數： | 7/17頁 |
| 文件大?。?/td> | 377K |
| 代理商： | MAX1062 |
第1頁第2頁第3頁第4頁第5頁第6頁當前第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁
Detailed Description
The MAX1062 includes an input track-and-hold (T/H)
and successive-approximation register (SAR) circuitry
to convert an analog input signal to a digital 14-bit out-
put. Figure 4 shows the MAX1062 in its simplest config-
uration. The serial interface requires only three digital
lines (SCLK,
CS
, and DOUT) and provides an easy
interface to microprocessors (μPs).
The MAX1062 has two power modes: normal and shut-
down. Driving
CS
high places the MAX1062 in shut-
down, reducing the supply current to 0.1μA (typ), while
pulling
CS
low places the MAX1062 in normal operating
mode. Falling edges on
CS
initiate conversions that are
driven by SCLK. The conversion result is available at
DOUT in unipolar serial format. The serial data stream
consists of eight zeros followed by the data bits (MSB
first). Figure 3 shows the interface-timing diagram.
Analog Input
Figure 5 illustrates the input sampling architecture of
the ADC. The voltage applied at REF sets the full-scale
input voltage.
Track-and-Hold (T/H)
In track mode, the analog signal is acquired on the
internal hold capacitor. In hold mode, the T/H switches
open and the capacitive DAC samples the analog
input.
During the acquisition, the analog input (AIN) charges
capacitor C
DAC
. The acquisition interval ends on the
falling edge of the sixth clock cycle (Figure 6). At this
instant, the T/H switches open. The retained charge on
C
DAC
represents a sample of the input.
In hold mode, the capacitive digital-to-analog converter
(DAC) adjusts during the remainder of the conversion
cycle to restore node ZERO to zero within the limits of
14-bit resolution. At the end of the conversion, force
CS
high and then low to reset the input side of the C
DAC
switches back to AIN, and charge C
DAC
to the input
signal again.
The time required for the T/H to acquire an input signal
is a function of how quickly its input capacitance is
charged. If the input signal
’
s source impedance is high,
the acquisition time lengthens and more time must be
allowed between conversions. The acquisition time
(t
ACQ
) is the maximum time the device takes to acquire
the signal. Use the following formula to calculate acqui-
sition time:
t
ACQ
= 11(R
S
+ R
IN
) x 35pF
where R
IN
= 800
, R
S
= the input signal
’
s source
impedance, and t
ACQ
is never less than 1.1μs. A
source impedance less than 1k
does not significantly
affect the ADC
’
s performance.
To improve the input signal bandwidth under AC condi-
tions, drive AIN with a wideband buffer (>4MHz) that
can drive the ADC
’
s input capacitance and settle
quickly.
M
14-Bit, +5V, 200ksps ADC with 10μA Shutdown
_______________________________________________________________________________________
7
Pin Description
PIN
NAME
FUNCTION
1
REF
External Reference Voltage Input. Sets the analog voltage range. Bypass to AGND with a 4.7μF
capacitor.
2
AV
DD
AGND
Analog +5V Supply Voltage. Bypass to AGND (pin 3) with a 0.1μF capacitor.
Analog Ground. Connect pins 3 and 9 together. Place star ground at pin 3.
3, 9
4
CS
Active Low Chip Select Input. Forcing
CS
high places the MAX1062 in shutdown with a typical
current of 0.1μA. A high-to-low transition on
CS
activates normal operating mode and initiates a
conversion.
5
SCLK
Serial Clock Input. SCLK drives the conversion process and clocks out data at data rates up to
4.8MHz.
6
DOUT
Serial Data Output. Data changes state on SCLK
’
s falling edge. DOUT is high impedance when
CS
is high.
7
8
10
DGND
DV
DD
AIN
Digital Ground
Digital Supply Voltage. Bypass to DGND with a 0.1μF capacitor.
Analog Input
相關PDF資料 |
PDF描述 |
|---|---|
| MAX1062ACUB | 14-Bit, %V, 200ksps ADC with 10レA Shutdown |
| MAX1065ACUI | Low-Power, 14-Bit Analog-to-Digital Converters with Parallel Interface |
| MAX1065AEUI | Low-Power, 14-Bit Analog-to-Digital Converters with Parallel Interface |
| MAX1065BCUI | Low-Power, 14-Bit Analog-to-Digital Converters with Parallel Interface |
| MAX1065BEUI | Low-Power, 14-Bit Analog-to-Digital Converters with Parallel Interface |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MAX1062_09 | 制造商:MAXIM 制造商全稱:Maxim Integrated Products 功能描述:14-Bit, +5V, 200ksps ADC with 10μA Shutdown |
| MAX1062ACUB | 功能描述:模數轉換器 - ADC RoHS:否 制造商:Texas Instruments 通道數量:2 結構:Sigma-Delta 轉換速率:125 SPs to 8 KSPs 分辨率:24 bit 輸入類型:Differential 信噪比:107 dB 接口類型:SPI 工作電源電壓:1.7 V to 3.6 V, 2.7 V to 5.25 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:VQFN-32 |
| MAX1062ACUB+ | 功能描述:模數轉換器 - ADC 5V 14-Bit 200ksp w/10uA Shutdown RoHS:否 制造商:Texas Instruments 通道數量:2 結構:Sigma-Delta 轉換速率:125 SPs to 8 KSPs 分辨率:24 bit 輸入類型:Differential 信噪比:107 dB 接口類型:SPI 工作電源電壓:1.7 V to 3.6 V, 2.7 V to 5.25 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:VQFN-32 |
| MAX1062ACUB+T | 功能描述:模數轉換器 - ADC 5V 14-Bit 200ksp w/10uA Shutdown RoHS:否 制造商:Texas Instruments 通道數量:2 結構:Sigma-Delta 轉換速率:125 SPs to 8 KSPs 分辨率:24 bit 輸入類型:Differential 信噪比:107 dB 接口類型:SPI 工作電源電壓:1.7 V to 3.6 V, 2.7 V to 5.25 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:VQFN-32 |
| MAX1062ACUB-T | 功能描述:模數轉換器 - ADC RoHS:否 制造商:Texas Instruments 通道數量:2 結構:Sigma-Delta 轉換速率:125 SPs to 8 KSPs 分辨率:24 bit 輸入類型:Differential 信噪比:107 dB 接口類型:SPI 工作電源電壓:1.7 V to 3.6 V, 2.7 V to 5.25 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:VQFN-32 |
發布緊急采購，3分鐘左右您將得到回復。