參數資料
型號： MAX1042BETX+
廠商： Maxim Integrated Products
文件頁數： 11/39頁
文件大?。?/td> 0K
描述： IC ADC/DAC 10BIT W/FIFO 36TQFN
產品培訓模塊： Lead (SnPb) Finish for COTS
Obsolescence Mitigation Program
標準包裝： 50
類型： ADC，DAC
分辨率（位）： 10 b
采樣率（每秒）： 225k
數據接口： DSP，MICROWIRE?，QSPI?，串行，SPI?
電壓電源： 模擬和數字
電源電壓： 4.75 V ~ 5.25 V
工作溫度： -40°C ~ 85°C
安裝類型： 表面貼裝
封裝/外殼： 36-WFQFN 裸露焊盤
供應商設備封裝： 36-TQFN 裸露焊盤（6x6）
包裝： 管件
MAX1040/MAX1042/MAX1046/MAX1048
10-Bit, Multichannel ADCs/DACs with FIFO,
Temperature Sensing, and GPIO Ports
______________________________________________________________________________________
19
Write to the GPIOs by writing a command byte to the
GPIO command register. Write a single data byte to the
MAX1042/MAX1048 following the command byte.
The GPIOs can sink and source current. The
MAX1042/MAX1048 GPIOA0 and GPIOA1 can sink and
source up to 15mA. GPIOC0 and GPIOC1 can sink 4mA
and source 2mA. See Table 3.
Clock Modes
Internal Clock
The MAX1040/MAX1042/MAX1046/MAX1048 can oper-
ate from an internal oscillator. The internal oscillator is
active in clock modes 00, 01, and 10. Figures 6, 7, and
8 show how to start an ADC conversion in the three
internally timed conversion modes.
Read out the data at clock speeds up to 25MHz
through the SPI interface.
External Clock
Set CKSEL1 and CKSEL0 in the setup register to 11 to
set up the interface for external clock mode 11. See
Table 5. Pulse SCLK at speeds from 0.1MHz to
3.6MHz. Write to SCLK with a 40% to 60% duty cycle.
The SCLK frequency controls the conversion timing.
See Figure 9 for clock mode 11 timing. See the
ADC
Conversions in Clock Mode 11 section.
ADC/DAC References
Address the reference through the setup register, bits 3
and 2. See Table 5. Following a wake-up delay, set
REFSEL[1:0] = 00 to program both the ADC and DAC
for internal reference use. Set REFSEL[1:0] = 10 to pro-
gram the ADC for internal reference. Set REFSEL[1:0] =
10 to program the DAC for external reference, REF1.
When using REF1 or REF2/AIN_ in external-reference
mode, connect a 0.1F capacitor to AGND. Set
REFSEL[1:0] = 01 to program the ADC and DAC for
external-reference mode. The DAC uses REF1 as its
external reference, while the ADC uses REF2 as its
external reference. Set REFSEL[1:0] = 11 to program
the ADC for external differential-reference mode. REF1
is the positive reference and REF2 is the negative refer-
ence in the ADC external differential mode.
When REFSEL[1:0] = 00 or 10, REF2/AIN_ functions as
an analog input channel. When REFSEL[1:0] = 01 or 11,
REF2/AIN_ functions as the device’s negative reference.
Temperature Measurements
Issue a command byte setting bit 0 of the conversion
register to one to take a temperature measurement.
See Table 4. The MAX1040/MAX1042/MAX1046/
MAX1048 perform temperature measurements with an
internal diode-connected transistor. The diode bias cur-
rent changes from 68A to 4A to produce a tempera-
ture-dependent bias voltage difference. The second
conversion result at 4A is subtracted from the first at
68A to calculate a digital value that is proportional to
absolute temperature. The output data appearing at
DOUT is the digital code above, minus an offset to
adjust from Kelvin to Celsius.
The reference voltage used for the temperature mea-
surements is always derived from the internal reference
source to ensure that 1 LSB corresponds to 1/8th of a
degree Celsius. On every scan where a temperature
measurement is requested, the 12-bit temperature con-
version is carried out first. The first 2 bytes of data read
from the FIFO contain the result of the 12-bit tempera-
ture measurement. If another temperature measure-
ment is performed before the first temperature result is
read out, the old measurement is overwritten by the
new result. Temperature results are in degrees Celsius
(two’s complement). See the
Applications Information
section for information on how to perform temperature
measurements in each clock mode.
Register Descriptions
The MAX1040/MAX1042/MAX1046/MAX1048 communi-
cate between the internal registers and the external cir-
cuitry through the SPI-compatible serial interface. Table
1 details the command byte, the registers, and the bit
names. Tables 4–12 show the various functions within
the conversion register, setup register, unipolar-mode
register, bipolar-mode register, ADC averaging regis-
ter, DAC select register, reset register, and GPIO com-
mand register, respectively.
Conversion Register
Select active analog input channels, scan modes, and
a single temperature measurement per scan by issuing
a command byte to the conversion register. Table 4
details channel selection, the four scan modes, and
how to request a temperature measurement. Start a
scan by writing to the conversion register when in clock
mode 10 or 11, or by applying a low pulse to the
CNVST pin when in clock mode 00 or 01. See Figures 6
MAX1042/MAX1048
(mA)
CURRENT
GPIOA0, GPIOA1
GPIOC0, GPIOC1
Sink
15
4
Source
15
2
Table 3. GPIO Maximum Sink/Source
Current
相關PDF資料
PDF描述
MAX1057BETM+T IC ADC/DAC 10BIT 48-TQFN-EP
MAX11041ETC+T IC REMOTE CTRLR WIRED 12-TQFN
MAX11043ATL+T IC ADC 16BIT W/DAC 40-TQFN-EP
MAX11359AETL+T IC DAS SYSTEM 16BIT 40-TQFN
MAX115CAX+ IC DAS SYSTEM 12BIT 36-SSOP
相關代理商/技術參數
參數描述
MAX1042BETX+ 功能描述:ADC / DAC多通道 10Bit AD/DACs w/FIFO Temp Sns & GPIO Port RoHS:否 制造商:Texas Instruments 轉換速率: 分辨率:8 bit 接口類型:SPI 電壓參考: 電源電壓-最大:3.6 V 電源電壓-最小:2 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:VQFN-40
MAX1042BETX+T 功能描述:ADC / DAC多通道 10Bit AD/DACs w/FIFO Temp Sns & GPIO Port RoHS:否 制造商:Texas Instruments 轉換速率: 分辨率:8 bit 接口類型:SPI 電壓參考: 電源電壓-最大:3.6 V 電源電壓-最小:2 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:VQFN-40
MAX1042BETX-T 功能描述:ADC / DAC多通道 RoHS:否 制造商:Texas Instruments 轉換速率: 分辨率:8 bit 接口類型:SPI 電壓參考: 電源電壓-最大:3.6 V 電源電壓-最小:2 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:VQFN-40
MAX1043 制造商:MAXIM 制造商全稱:Maxim Integrated Products 功能描述:10-Bit, Multichannel ADCs/DACs with FIFO, Temperature Sensing, and GPIO Ports
MAX1043BETX 功能描述:ADC / DAC多通道 RoHS:否 制造商:Texas Instruments 轉換速率: 分辨率:8 bit 接口類型:SPI 電壓參考: 電源電壓-最大:3.6 V 電源電壓-最小:2 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:VQFN-40
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*