- 您現在的位置：買賣IC網 > PDF目錄9468 > MAX1040BETX+ (Maxim Integrated Products)IC ADC/DAC 10BIT W/FIFO 36TQFN PDF資料下載
參數資料
| 型號： | MAX1040BETX+ |
| 廠商： | Maxim Integrated Products |
| 文件頁數： | 13/39頁 |
| 文件大小： | 0K |
| 描述： | IC ADC/DAC 10BIT W/FIFO 36TQFN |
| 產品培訓模塊： | Lead (SnPb) Finish for COTS Obsolescence Mitigation Program |
| 標準包裝： | 50 |
| 類型： | ADC，DAC |
| 分辨率（位）： | 10 b |
| 采樣率（每秒）： | 225k |
| 數據接口： | DSP，MICROWIRE?，QSPI?，串行，SPI? |
| 電壓電源： | 模擬和數字 |
| 電源電壓： | 4.75 V ~ 5.25 V |
| 工作溫度： | -40°C ~ 85°C |
| 安裝類型： | 表面貼裝 |
| 封裝/外殼： | 36-WFQFN 裸露焊盤 |
| 供應商設備封裝： | 36-TQFN 裸露焊盤（6x6） |
| 包裝： | 管件 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁當前第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁
MAX1040/MAX1042/MAX1046/MAX1048
10-Bit, Multichannel ADCs/DACs with FIFO,
Temperature Sensing, and GPIO Ports
20
______________________________________________________________________________________
and 7 for timing specifications for starting a scan with
CNVST.
A conversion is not performed if it is requested on a
channel or one of the channel pairs that has been con-
figured as
CNVST or REF2. For channels configured as
differential pairs, the CHSEL0 bit is ignored and the two
pins are treated as a single differential channel. For the
MAX1046/MAX1048, the CHSEL2 bit must be zero.
Channels 4–7 are invalid. Any scans or averages on
these channels can cause corrupt data.
Select scan mode 00 or 01 to return one result per sin-
gle-ended channel and one result per differential pair
within the selected scanning range (set by bits 2 and 1,
SCAN1 and SCAN0), plus one temperature result if
selected. Select scan mode 10 to scan a single input
channel numerous times, depending on NSCAN1 and
NSCAN0 in the ADC averaging register (Table 9).
Select scan mode 11 to return only one result from a
single channel.
Setup Register
Issue a command byte to the setup register to config-
ure the clock, reference, power-down modes, and ADC
single-ended/differential modes. Table 5 details the bits
in the setup-register command byte. Bits 5 and 4
(CKSEL1 and CKSEL0) control the clock mode, acqui-
sition and sampling, and the conversion start. Bits 3
and 2 (REFSEL1 and REFSEL0) set the device for either
internal or external reference. Bits 1 and 0 (DIFFSEL1
and DIFFSEL0) address the ADC unipolar-mode and
bipolar-mode registers and configure the analog input
channels for differential operation.
The ADC reference is always on if any of the following
conditions are true:
1)The FBGON bit is set to one in the reset register.
2)At least one DAC output is powered up and
REFSEL[1:0] (in the setup register) = 00.
3)At least one DAC is powered down through the
100kΩ to VREF and REFSEL[1:0] = 00.
If any of the above conditions exist, the ADC reference
is always on, but there is a 188 clock-cycle delay
before temperature-sensor measurements begin, if
requested.
Table 4. Conversion Register*
BIT
NAME
BIT
FUNCTION
—
7 (MSB)
Set to one to select conversion register.
X
6
Don’t care.
CHSEL2
5
Analog-input channel select
(MAX1040/MAX1042). Set to 0 on
MAX1046/MAX1048.
CHSEL1
4
Analog-input channel select.
CHSEL0
3
Analog-input channel select.
SCAN1
2
Scan-mode select.
SCAN0
1
Scan-mode select.
TEMP
0 (LSB)
Set to one to take a single temp-
erature measurement. The first
conversion result of a scan contains
temperature information.
CHSEL2**
CHSEL1
CHSEL0
SELECTED
CHANNEL
(N)
00
0
AIN0
00
1
AIN1
01
0
AIN2
01
1
AIN3
10
0
AIN4
10
1
AIN5
11
0
AIN6
11
1
AIN7
SCAN1
SCAN0
SCAN MODE
(CHANNEL N IS SELECTED BY
BITS CHSEL2, CHSEL1, AND CHSEL0)
0
Scans channels 0 through N.
01
Scans channels N through the highest
numbered channel.
10
Scans channel N repeatedly. The ADC
averaging register sets the number of
results.
11
No scan. Converts channel N once only.
*
See below for bit details.
**
Channels 4–7 are invalid on the MAX1046/MAX1048. Set
CHSEL2 bit to 0 on those devices.
相關PDF資料 |
PDF描述 |
|---|---|
| MS3121F12-8PX | CONN RCPT 8POS CBL MNT W/PINS |
| LTC1799CS5#TR | IC OSC SILICON 33MHZ TSOT23-5 |
| AD7874SQ | IC DAS 12BIT 4CH 5V 28-CDIP |
| MS27466T25B35PB | CONN RCPT 128POS WALL MNT W/PINS |
| MAX1407CAI+T | IC DAS 16BIT LP 28-SSOP |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MAX1040BETX+ | 功能描述:ADC / DAC多通道 10Bit AD/DACs w/FIFO Temp Sns & GPIO Port RoHS:否 制造商:Texas Instruments 轉換速率: 分辨率:8 bit 接口類型:SPI 電壓參考: 電源電壓-最大:3.6 V 電源電壓-最小:2 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:VQFN-40 |
| MAX1040BETX+T | 功能描述:ADC / DAC多通道 10Bit AD/DACs w/FIFO Temp Sns & GPIO Port RoHS:否 制造商:Texas Instruments 轉換速率: 分辨率:8 bit 接口類型:SPI 電壓參考: 電源電壓-最大:3.6 V 電源電壓-最小:2 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:VQFN-40 |
| MAX1040BETX-T | 功能描述:ADC / DAC多通道 RoHS:否 制造商:Texas Instruments 轉換速率: 分辨率:8 bit 接口類型:SPI 電壓參考: 電源電壓-最大:3.6 V 電源電壓-最小:2 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:VQFN-40 |
| MAX1041BETX | 制造商:MAXIM 制造商全稱:Maxim Integrated Products 功能描述:10-Bit, Multichannel ADCs/DACs with FIFO, Temperature Sensing, and GPIO Ports |
| MAX1042 | 制造商:MAXIM 制造商全稱:Maxim Integrated Products 功能描述:10-Bit, Multichannel ADCs/DACs with FIFO, Temperature Sensing, and GPIO Ports |
發布緊急采購，3分鐘左右您將得到回復。