- 您現在的位置：買賣IC網 > PDF目錄383308 > MAX1039AEEE (MAXIM INTEGRATED PRODUCTS INC) LJT 8C 8#20 PIN RECP PDF資料下載
參數資料
| 型號： | MAX1039AEEE |
| 廠商： | MAXIM INTEGRATED PRODUCTS INC |
| 元件分類： | ADC |
| 英文描述： | LJT 8C 8#20 PIN RECP |
| 中文描述： | 12-CH 8-BIT SUCCESSIVE APPROXIMATION ADC, SERIAL ACCESS, PDSO16 |
| 封裝： | 0.150 INCH, MO-137, QSOP-16 |
| 文件頁數： | 14/22頁 |
| 文件大?。?/td> | 427K |
| 代理商： | MAX1039AEEE |
M
in random access memory (RAM). If the scan mode is
set for multiple conversions, they all happen in succes-
sion with each additional result being stored in RAM.
The MAX1036/MAX1037 contain 8 bytes of RAM, and
the MAX1038/MAX1039 contain 12 bytes of RAM. Once
all conversions are complete, the MAX1036
–
MAX1039
release SCL, allowing it to be pulled high. The master
can now clock the results out of the output shift register
at a clock rate of up to 1.7MHz. SCL is stretched for a
maximum acquisition and conversion time of 7.6μs per
channel (Figure 10).
The device RAM contains all of the conversion results
when the MAX1036
–
MAX1039 release SCL. The con-
verted results are read back in a first-in-first-out (FIFO)
sequence. If AIN_/REF is set to be a reference input or
output (SEL1 = 1, Table 6), AIN_/REF is excluded from
a multichannel scan. RAM contents can be read contin-
uously. If reading continues past the last result stored in
RAM, the pointer wraps around and points to the first
result. Note that only the current conversion results are
read from memory. The device must be addressed with
a read command to obtain new conversion results.
The internal clock mode
’
s clock stretching quiets the
SCL bus signal, reducing the system noise during con-
version. Using the internal clock also frees the master
(typically a microcontroller) from the burden of running
the conversion clock.
External Clock
When configured for external clock mode (CLK = 1),
the MAX1036
–
MAX1039 use SCL as the conversion
clock. In external clock mode, the MAX1036
–
MAX1039
begin tracking the analog input on the seventh falling
clock edge of a valid slave address byte. One SCL
clock cycle later, the analog signal is acquired and the
conversion begins. Unlike internal clock mode, convert-
ed data is available immediately after the slave-address
acknowledge bit. The device continuously converts
input channels dictated by the scan mode until given a
not acknowledge. There is no need to readdress the
device with a read command to obtain new conversion
results (Figure 11).
The conversion must complete in 9ms or droop on the
T/H capacitor degrades conversion results. Use internal
clock mode if the SCL clock period exceeds 1ms.
The MAX1036
–
MAX1039 must operate in external clock
mode for conversion rates up to 188ksps.
Scan Mode
SCAN0 and SCAN1 of the configuration byte set the
scan mode configuration. Table 5 shows the scanning
configurations. If AIN_/REF is set to be a reference input
or output (SEL1 = 1, Table 6), AIN_/REF is excluded
from a multichannel scan.
2.7V to 5.5V, Low-Power, 4-/12-Channel
2-Wire Serial 8-Bit ADCs
14
______________________________________________________________________________________
B. 2-BYTE WRITE CYCLE
SLAVE TO MASTER
MASTER TO SLAVE
S
1
SLAVE ADDRESS
A
7
1 1
W
SETUP OR
CONFIGURATION BYTE
SETUP OR
CONFIGURATION BYTE
8
P OR Sr
1
A
1
MSB DETERMINES WHETHER
SETUP OR CONFIGURATION BYTE
S
1
SLAVE ADDRESS
A
7
1 1
W
SETUP OR
CONFIGURATION BYTE
8
P OR Sr
1
A
1
MSB DETERMINES WHETHER
SETUP OR CONFIGURATION BYTE
A
1
8
A. 1-BYTE WRITE CYCLE
NUMBER OF BITS
NUMBER OF BITS
Figure 9. Write Cycle
相關PDF資料 |
PDF描述 |
|---|---|
| MAX1036 | 2.7V to 5.5V, Low-Power, 4-/12-Channel 2-Wire Serial 8-Bit ADCs |
| MAX1038 | 2.7V to 5.5V, Low-Power, 4-/12-Channel 2-Wire Serial 8-Bit ADCs |
| MAX1039 | 2.7V to 5.5V, Low-Power, 4-/12-Channel 2-Wire Serial 8-Bit ADCs |
| MAX1036EKA- | 2.7V to 5.5V, Low-Power, 4-/12-Channel 2-Wire Serial 8-Bit ADCs |
| MAX1062AEUB | 14-Bit, %V, 200ksps ADC with 10レA Shutdown |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MAX1039AEEE+ | 功能描述:模數轉換器 - ADC 3.3V 12-Bit 4Ch I2C Serial RoHS:否 制造商:Texas Instruments 通道數量:2 結構:Sigma-Delta 轉換速率:125 SPs to 8 KSPs 分辨率:24 bit 輸入類型:Differential 信噪比:107 dB 接口類型:SPI 工作電源電壓:1.7 V to 3.6 V, 2.7 V to 5.25 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:VQFN-32 |
| MAX1039AEEE+T | 功能描述:模數轉換器 - ADC 3.3V 12-Bit 4Ch I2C Serial RoHS:否 制造商:Texas Instruments 通道數量:2 結構:Sigma-Delta 轉換速率:125 SPs to 8 KSPs 分辨率:24 bit 輸入類型:Differential 信噪比:107 dB 接口類型:SPI 工作電源電壓:1.7 V to 3.6 V, 2.7 V to 5.25 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:VQFN-32 |
| MAX1039AEEE-T | 功能描述:模數轉換器 - ADC RoHS:否 制造商:Texas Instruments 通道數量:2 結構:Sigma-Delta 轉換速率:125 SPs to 8 KSPs 分辨率:24 bit 輸入類型:Differential 信噪比:107 dB 接口類型:SPI 工作電源電壓:1.7 V to 3.6 V, 2.7 V to 5.25 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:VQFN-32 |
| MAX1039KAEEE | 功能描述:模數轉換器 - ADC RoHS:否 制造商:Texas Instruments 通道數量:2 結構:Sigma-Delta 轉換速率:125 SPs to 8 KSPs 分辨率:24 bit 輸入類型:Differential 信噪比:107 dB 接口類型:SPI 工作電源電壓:1.7 V to 3.6 V, 2.7 V to 5.25 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:VQFN-32 |
| MAX1039LAEEE | 功能描述:模數轉換器 - ADC RoHS:否 制造商:Texas Instruments 通道數量:2 結構:Sigma-Delta 轉換速率:125 SPs to 8 KSPs 分辨率:24 bit 輸入類型:Differential 信噪比:107 dB 接口類型:SPI 工作電源電壓:1.7 V to 3.6 V, 2.7 V to 5.25 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:VQFN-32 |
發布緊急采購，3分鐘左右您將得到回復。