- 您現在的位置：買賣IC網 > PDF目錄383308 > MAX1036-MAX1039 (Maxim Integrated Products, Inc.) 2.7V to 5.5V, Low-Power, 4-/12-Channel 2-Wire Serial 8-Bit ADCs PDF資料下載
參數資料
| 型號： | MAX1036-MAX1039 |
| 廠商： | Maxim Integrated Products, Inc. |
| 英文描述： | 2.7V to 5.5V, Low-Power, 4-/12-Channel 2-Wire Serial 8-Bit ADCs |
| 中文描述： | 2.7V至5.5V，低功耗，4-/12-Channel 2線串行8位ADC |
| 文件頁數： | 9/22頁 |
| 文件大?。?/td> | 427K |
| 代理商： | MAX1036-MAX1039 |
of the address byte (see the
Slave Address
section).
The T/H circuitry enters hold mode two internal clock
cycles later. A conversion or series of conversions are
then internally clocked (eight clock cycles per conver-
sion) and the MAX1036
–
MAX1039 hold SCL low. When
operating in external clock mode, the T/H circuitry
enters track mode on the seventh falling edge of a valid
slave address byte. Hold mode is then entered on the
falling edge of the eighth clock cycle. The conversion is
performed during the next eight clock cycles.
The time required for the T/H circuitry to acquire an
input signal is a function of input capacitance. If the
analog input source impedance is high, the acquisition
time lengthens and more time must be allowed
between conversions. The acquisition time (t
ACQ
) is the
minimum time needed for the signal to be acquired. It
is calculated by:
t
ACQ
≥
6.25
(R
SOURCE
+ R
IN
)
C
IN
where R
SOURCE
is the analog input source impedance,
R
IN
= 2.5k
, and C
IN
= 18pF. t
ACQ
is 1/f
SCL
for external
clock mode. For internal clock mode, the acquisition
time is two internal clock cycles. To select R
SOURCE
,
allow 625ns for t
ACQ
in internal clock mode to account
for clock frequency variations.
M
2.7V to 5.5V, Low-Power, 4-/12-Channel
2-Wire Serial 8-Bit ADCs
_______________________________________________________________________________________
9
t
HD.STA
t
SU.DAT
t
HIGH
t
R
t
F
t
HD.DAT
t
HD.STA
S
Sr
A
SCL
SDA
t
SU.STA
t
LOW
t
BUF
t
SU.STO
P
S
t
HD.STA
t
SU.DAT
t
HIGH
t
FCL
t
HD.DAT
t
HD.STA
S
Sr
A
SCL
SDA
t
SU.STA
t
LOW
t
BUF
t
SU.STO
S
t
RCL
t
RCL1
HS-MODE
F/S-MODE
A. F/S-MODE I
2
C SERIAL INTERFACE TIMING
B. HS-MODE I
2
C SERIAL INTERFACE TIMING
t
FDA
t
RDA
t
t
R
t
F
Figure 1. I
2
C Serial Interface Timing
V
DD
I
OL
= 3mA
I
OH
= 0mA
V
OUT
400pF
SDA
Figure 2. Load Circuit
相關PDF資料 |
PDF描述 |
|---|---|
| MAX1038AEEE | LJT 4C 4#16 SKT RECP |
| MAX1039AEEE | LJT 8C 8#20 PIN RECP |
| MAX1036 | 2.7V to 5.5V, Low-Power, 4-/12-Channel 2-Wire Serial 8-Bit ADCs |
| MAX1038 | 2.7V to 5.5V, Low-Power, 4-/12-Channel 2-Wire Serial 8-Bit ADCs |
| MAX1039 | 2.7V to 5.5V, Low-Power, 4-/12-Channel 2-Wire Serial 8-Bit ADCs |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MAX1036MEKA | 制造商:Maxim Integrated Products 功能描述:- Cut Tape Product 制造商:Rochester Electronics LLC 功能描述: |
| MAX1036MEKA+ | 制造商:Maxim Integrated Products 功能描述:ADC SGL SAR 188KSPS 8BIT SERL 8PIN SOT-23 - Cut Tape Product |
| MAX1036MEKA+T | 功能描述:模數轉換器 - ADC RoHS:否 制造商:Texas Instruments 通道數量:2 結構:Sigma-Delta 轉換速率:125 SPs to 8 KSPs 分辨率:24 bit 輸入類型:Differential 信噪比:107 dB 接口類型:SPI 工作電源電壓:1.7 V to 3.6 V, 2.7 V to 5.25 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:VQFN-32 |
| MAX1036MEKA-T | 功能描述:模數轉換器 - ADC RoHS:否 制造商:Texas Instruments 通道數量:2 結構:Sigma-Delta 轉換速率:125 SPs to 8 KSPs 分辨率:24 bit 輸入類型:Differential 信噪比:107 dB 接口類型:SPI 工作電源電壓:1.7 V to 3.6 V, 2.7 V to 5.25 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:VQFN-32 |
| MAX1037 | 制造商:MAXIM 制造商全稱:Maxim Integrated Products 功能描述:2.7V to 5.5V, Low-Power, 4-/12-Channel 2-Wire Serial 8-Bit ADCs |
發布緊急采購，3分鐘左右您將得到回復。
