- 您現(xiàn)在的位置：買賣IC網 > PDF目錄10496 > MAX1035EUP+ (Maxim Integrated Products)IC ADC 14BIT SER 115KSPS 20TSSOP PDF資料下載
參數資料
| 型號： | MAX1035EUP+ |
| 廠商： | Maxim Integrated Products |
| 文件頁數： | 6/31頁 |
| 文件大小： | 0K |
| 描述： | IC ADC 14BIT SER 115KSPS 20TSSOP |
| 產品培訓模塊： | Lead (SnPb) Finish for COTS Obsolescence Mitigation Program |
| 標準包裝： | 74 |
| 位數： | 14 |
| 采樣率（每秒）： | 115k |
| 數據接口： | MICROWIRE?，串行，SPI? |
| 轉換器數目： | 1 |
| 功率耗散（最大）： | 879mW |
| 電壓電源： | 模擬和數字 |
| 工作溫度： | -40°C ~ 85°C |
| 安裝類型： | 表面貼裝 |
| 封裝/外殼： | 20-TSSOP（0.173"，4.40mm 寬） |
| 供應商設備封裝： | 20-TSSOP |
| 包裝： | 管件 |
| 輸入數目和類型： | 4 個單端，單極；4 個單端，雙極；2 個差分，單極；2 個差分，雙極 |
第1頁第2頁第3頁第4頁第5頁當前第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁
MAX1034/MAX1035
The MAX1034 has eight single-ended analog input
channels or four differential channels (see the
Block
Diagram at the end of the data sheet). The MAX1035
has four single-ended analog input channels or two dif-
ferential channels. Each analog input channel is inde-
pendently
software
programmable
for
seven
single-ended
input
ranges
(0
to
+VREF/2,
-VREF/2 to 0, 0 to +VREF, -VREF to 0, ±VREF/4, ±VREF/2,
and ±VREF) and three differential input ranges (±VREF/2,
±VREF, and ±2 x VREF). Additionally, all analog input
channels are fault tolerant to ±6V. A fault condition on
an idle channel does not affect the conversion result of
other channels.
Power Supplies
To maintain a low-noise environment, the MAX1034 and
MAX1035 provide separate power supplies for each
section of circuitry. Table 1 shows the four separate
power supplies. Achieve optimal performance using
separate AVDD1, AVDD2, DVDD, and DVDDO supplies.
Alternatively, connect AVDD1, AVDD2, and DVDD
together as close to the device as possible for a conve-
nient power connection. Connect AGND1, AGND2,
AGND3, DGND, and DGNDO together as close to the
device as possible. Bypass each supply to the corre-
sponding ground using a 0.1F capacitor (Table 1). If
significant low-frequency noise is present, add a 10F
capacitor in parallel with the 0.1F bypass capacitor.
Converter Operation
The MAX1034/MAX1035 ADCs feature a fully differen-
tial, successive-approximation register (SAR) conver-
sion technique and an on-chip T/H block to convert
voltage signals into a 14-bit digital result. Both single-
ended and differential configurations are supported
with programmable unipolar and bipolar signal ranges.
Track-and-Hold Circuitry
The MAX1034/MAX1035 feature a switched-capacitor
T/H architecture that allows the analog input signal to be
stored as charge on sampling capacitors. See Figures 2,
3, and 4 for T/H timing and the sampling instants for
each operating mode. The MAX1034/MAX1035 analog
input circuitry buffers the input signal from the sampling
capacitors, resulting in a constant analog input current
with varying input voltage (Figure 5).
8-/4-Channel, ±VREF Multirange Inputs,
Serial 14-Bit ADCs
14
______________________________________________________________________________________
Table 1. MAX1034/MAX1035 Power Supplies and Bypassing
POWER
SUPPLY/GROUND
SUPPLY VOLTAGE
RANGE (V)
TYPICAL SUPPLY
CURRENT (mA)
CIRCUIT SECTION
BYPASSING
DVDDO/DGNDO
2.7 to 5.25
0.2
Digital I/O
0.1F to DGNDO
AVDD2/AGND2
4.75 to 5.25
17.5
Analog Circuitry
0.1F to AGND2
AVDD1/AGND1
4.75 to 5.25
3.0
Analog Circuitry
0.1F to AGND1
DVDD/DGND
4.75 to 5.25
0.9
Digital Control Logic and
Memory
0.1F to DGND
Table 2. Analog Input Configuration Byte
BIT
NUMBER
NAME
DESCRIPTION
7
START
Start Bit. The first logic 1 after
CS goes low defines the beginning of the analog input configuration byte.
6C2
5C1
4C0
Channel-Select Bits. SEL[2:0] select the analog input channel to be configured (Tables 4 and 5).
3
DIF/
SGL
Differential or Single-Ended Configuration Bit. DIF/
SGL = 0 configures the selected analog input channel
for single-ended operation. DIF/
SGL = 1 configures the channel for differential operation. In single-ended
mode, input voltages are measured between the selected input channel and AGND1, as shown in
Table 4. In differential mode, the input voltages are measured between two input channels, as shown in
Table 5. Be aware that changing DIF/
SGL adjusts the FSR, as shown in Table 6.
2R2
1R1
0R0
Input-Range-Select Bits. R[2:0] select the input voltage range, as shown in Table 6 and Figure 7.
相關PDF資料 |
PDF描述 |
|---|---|
| MAX241EEWI+ | IC RS-232 DRVR/RCVR 28-SOIC |
| VI-B52-IV-F4 | CONVERTER MOD DC/DC 15V 150W |
| MAX3241EWI+ | IC TXRX RS-232 LP 28-SOIC |
| MAX1092ACEG+ | IC ADC 10BIT 400KSPS 24-QSOP |
| VI-B52-IV-F3 | CONVERTER MOD DC/DC 15V 150W |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MAX1035EUP+ | 功能描述:模數轉換器 - ADC 4Ch 1VRef Multi Inputs Serial 14-Bit RoHS:否 制造商:Texas Instruments 通道數量:2 結構:Sigma-Delta 轉換速率:125 SPs to 8 KSPs 分辨率:24 bit 輸入類型:Differential 信噪比:107 dB 接口類型:SPI 工作電源電壓:1.7 V to 3.6 V, 2.7 V to 5.25 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:VQFN-32 |
| MAX1035EUP+T | 功能描述:模數轉換器 - ADC 4Ch 1VRef Multi Inputs Serial 14-Bit RoHS:否 制造商:Texas Instruments 通道數量:2 結構:Sigma-Delta 轉換速率:125 SPs to 8 KSPs 分辨率:24 bit 輸入類型:Differential 信噪比:107 dB 接口類型:SPI 工作電源電壓:1.7 V to 3.6 V, 2.7 V to 5.25 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:VQFN-32 |
| MAX1035EUP-T | 功能描述:模數轉換器 - ADC RoHS:否 制造商:Texas Instruments 通道數量:2 結構:Sigma-Delta 轉換速率:125 SPs to 8 KSPs 分辨率:24 bit 輸入類型:Differential 信噪比:107 dB 接口類型:SPI 工作電源電壓:1.7 V to 3.6 V, 2.7 V to 5.25 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:VQFN-32 |
| MAX1036 | 制造商:MAXIM 制造商全稱:Maxim Integrated Products 功能描述:2.7V to 3.6V and 4.5V to 5.5V, Low-Power, 4-/12-Channel 2-Wire Serial 8-Bit ADCs |
| MAX1036_09 | 制造商:MAXIM 制造商全稱:Maxim Integrated Products 功能描述:2.7V to 3.6V and 4.5V to 5.5V, Low-Power, 4-/12-Channel 2-Wire Serial 8-Bit ADCs |
發(fā)布緊急采購，3分鐘左右您將得到回復。