- 您現在的位置：買賣IC網 > PDF目錄9955 > MAX1030BCEG+T (Maxim Integrated Products)IC ADC 10BIT 300KSPS 24-QSOP PDF資料下載
參數資料
| 型號： | MAX1030BCEG+T |
| 廠商： | Maxim Integrated Products |
| 文件頁數： | 5/22頁 |
| 文件大?。?/td> | 0K |
| 描述： | IC ADC 10BIT 300KSPS 24-QSOP |
| 產品培訓模塊： | Lead (SnPb) Finish for COTS Obsolescence Mitigation Program |
| 標準包裝： | 2,500 |
| 位數： | 10 |
| 采樣率（每秒）： | 300k |
| 數據接口： | MICROWIRE?，QSPI?，串行，SPI? |
| 轉換器數目： | 1 |
| 功率耗散（最大）： | 9.5mW |
| 電壓電源： | 單電源 |
| 工作溫度： | 0°C ~ 70°C |
| 安裝類型： | 表面貼裝 |
| 封裝/外殼： | 24-SSOP（0.154"，3.90mm 寬） |
| 供應商設備封裝： | 24-QSOP |
| 包裝： | 帶卷 (TR) |
| 輸入數目和類型： | 16 個單端，單極；16 個單端，雙極；8 個差分，單極；8 個差分，雙極 |
MAX1026/MAX1028/MAX1030
10-Bit 300ksps ADCs with FIFO,
Temp Sensor, Internal Reference
______________________________________________________________________________________
13
Setup Register
Write a byte to the setup register to configure the clock,
reference, and power-down modes. Table 3 details the
bits in the setup register. Bits 5 and 4 (CKSEL1 and
CKSEL0) control the clock mode, acquisition and sam-
pling, and the conversion start. Bits 3 and 2 (REFSEL1
and REFSEL0) control internal or external reference use.
Bits 1 and 0 (DIFFSEL1 and DIFFSEL0) address the
unipolar mode and bipolar mode registers and configure
the analog input channels for differential operation.
Unipolar/Bipolar Registers
The final 2 bits (LSBs) of the setup register control the
unipolar/bipolar mode address registers. Set bits 1 and
0 (DIFFSEL1 and DIFFSEL0) to 10 to write to the unipo-
lar mode register. Set bits 1 and 0 to 11 to write to the
bipolar mode register. In both cases, the setup byte
must be followed immediately by 1 byte of data written
to the unipolar register or bipolar register. Hold
CS low
and run 16 SCLK cycles before pulling
CS high. If the
last 2 bits of the setup register are 00 or 01, neither the
unipolar mode register nor the bipolar mode register is
written. Any subsequent byte is recognized as a new
input data byte. See Tables 4 and 5 to program the
unipolar and bipolar mode registers.
If a channel is configured as both unipolar and bipolar,
the unipolar setting takes precedence. In unipolar
mode, AIN+ can exceed AIN- by up to VREF. The out-
put format in unipolar mode is binary. In bipolar mode,
either input can exceed the other by up to VREF / 2. The
output format in bipolar mode is two's complement.
Averaging Register
Write to the averaging register to configure the ADC to
average up to 32 samples for each requested result,
and to independently control the number of results
requested for single-channel scans.
Table 2 details the four scan modes available in the con-
version register. All four scan modes allow averaging as
long as the AVGON bit, bit 4 in the averaging register, is
set to 1. Select scan mode 10 to scan the same channel
multiple times. Clock mode 11 disables averaging.
Reset Register
Write to the reset register (as shown in Table 7) to clear
the FIFO or to reset all registers to their default states.
Set the
RESET bit to 1 to reset the FIFO. Set the reset
bit to zero to return the MAX1026/MAX1028/MAX1030
to the default power-up state.
BIT
NAME
BIT
FUNCTION
—
7 (MSB) Set to 1 to select conversion register.
CHSEL3
6
Analog input channel select.
CHSEL2
5
Analog input channel select.
CHSEL1
4
Analog input channel select.
CHSEL0
3
Analog input channel select.
SCAN1
2
Scan mode select.
SCAN0
1
Scan mode select.
TEMP
0 (LSB)
Set to 1 to take a single temperature
measurement. The first conversion result
of a scan contains temperature information.
Table 2. Conversion Register*
*
See below for bit details.
CHSEL3
CHSEL2
CHSEL1
CHSEL0
SELECTED
CHANNEL (N)
0
AIN0
0
1
AIN1
0
1
0
AIN2
0
1
AIN3
0
1
0
AIN4
0
1
0
1
AIN5
0
1
0
AIN6
0
1
AIN7
1
0
AIN8
1
0
1
AIN9
1
0
1
0
AIN10
1
0
1
AIN11
1
0
AIN12
1
0
1
AIN13
1
0
AIN14
1
AIN15
SCAN1 SCAN0
SCAN MODE (CHANNEL N IS
SELECTED BY BITS CHSEL3–CHSEL0)
0
Scans channels 0 through N.
01
Scans channels N through the highest
numbered channel.
10
Scans channel N repeatedly. The averaging
register sets the number of results.
1
No scan. Converts channel N once only.
相關PDF資料 |
PDF描述 |
|---|---|
| V72B28M250BF | CONVERTER MOD DC/DC 28V 250W |
| VE-B6X-IV-F1 | CONVERTER MOD DC/DC 5.2V 150W |
| VI-B1J-MW-F2 | CONVERTER MOD DC/DC 36V 100W |
| VE-B6W-IV-F4 | CONVERTER MOD DC/DC 5.5V 150W |
| VI-B1L-MW-F2 | CONVERTER MOD DC/DC 28V 100W |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MAX1030BCGI-T | 制造商:MAXIM 制造商全稱:Maxim Integrated Products 功能描述:10-Bit 300ksps ADCs with FIFO, Temp Sensor, Internal Reference |
| MAX1030BCTI | 功能描述:模數轉換器 - ADC RoHS:否 制造商:Texas Instruments 通道數量:2 結構:Sigma-Delta 轉換速率:125 SPs to 8 KSPs 分辨率:24 bit 輸入類型:Differential 信噪比:107 dB 接口類型:SPI 工作電源電壓:1.7 V to 3.6 V, 2.7 V to 5.25 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:VQFN-32 |
| MAX1030BCTI+ | 功能描述:模數轉換器 - ADC 10Bit 300ksps w/FIFO Temp Sensor Int Ref RoHS:否 制造商:Texas Instruments 通道數量:2 結構:Sigma-Delta 轉換速率:125 SPs to 8 KSPs 分辨率:24 bit 輸入類型:Differential 信噪比:107 dB 接口類型:SPI 工作電源電壓:1.7 V to 3.6 V, 2.7 V to 5.25 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:VQFN-32 |
| MAX1030BCTI+T | 功能描述:模數轉換器 - ADC 10Bit 300ksps w/FIFO Temp Sensor Int Ref RoHS:否 制造商:Texas Instruments 通道數量:2 結構:Sigma-Delta 轉換速率:125 SPs to 8 KSPs 分辨率:24 bit 輸入類型:Differential 信噪比:107 dB 接口類型:SPI 工作電源電壓:1.7 V to 3.6 V, 2.7 V to 5.25 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:VQFN-32 |
| MAX1030BCTI-T | 功能描述:模數轉換器 - ADC RoHS:否 制造商:Texas Instruments 通道數量:2 結構:Sigma-Delta 轉換速率:125 SPs to 8 KSPs 分辨率:24 bit 輸入類型:Differential 信噪比:107 dB 接口類型:SPI 工作電源電壓:1.7 V to 3.6 V, 2.7 V to 5.25 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:VQFN-32 |
發布緊急采購，3分鐘左右您將得到回復。