- 您現在的位置：買賣IC網 > PDF目錄299460 > MAX1029ACEP-T (MAXIM INTEGRATED PRODUCTS INC) 10-Bit 300ksps ADCs with FIFO,Temp Sensor, Internal Reference PDF資料下載
參數資料
| 型號： | MAX1029ACEP-T |
| 廠商： | MAXIM INTEGRATED PRODUCTS INC |
| 元件分類： | ADC |
| 英文描述： | 10-Bit 300ksps ADCs with FIFO,Temp Sensor, Internal Reference |
| 中文描述： | 12-CH 10-BIT SUCCESSIVE APPROXIMATION ADC, SERIAL ACCESS, PDSO20 |
| 封裝： | 0.150 INCH, 0.025 INCH PITCH, MO-137AD, QSOP-20 |
| 文件頁數： | 5/24頁 |
| 文件大小： | 470K |
| 代理商： | MAX1029ACEP-T |
MAX1027/MAX1029/MAX1031
10-Bit 300ksps ADCs with FIFO,
Temp Sensor, Internal Reference
______________________________________________________________________________________
13
pair and one of them has been reconfigured as CNVST
or REF-, the pair is ignored.
Select scan mode 00 or 01 to return one result per sin-
gle-ended channel and one result per differential pair
within the requested range, plus one temperature result
if selected. Select scan mode 10 to scan a single input
channel numerous times, depending on NSCAN1 and
NSCAN0 in the averaging register (see Table 6). Select
scan mode 11 to return only one result from a single
channel.
Setup Register
Write a byte to the setup register to configure the clock,
reference, and power-down modes. Table 3 details the
bits in the setup register. Bits 5 and 4 (CKSEL1 and
CKSEL0) control the clock mode, acquisition and sam-
pling, and the conversion start. Bits 3 and 2 (REFSEL1
and REFSEL0) control internal or external reference use.
Bits 1 and 0 (DIFFSEL1 and DIFFSEL0) address the
unipolar mode and bipolar mode registers and configure
the analog input channels for differential operation.
Unipolar/Bipolar Registers
The final 2 bits (LSBs) of the setup register control the
unipolar/bipolar mode address registers. Set bits 1 and
0 (DIFFSEL1 and DIFFSEL0) to 10 to write to the unipo-
lar mode register. Set bits 1 and 0 to 11 to write to the
bipolar mode register. In both cases, the setup byte
must be followed immediately by 1 byte of data written
to the unipolar register or bipolar register. Hold CS low
and run 16 SCLK cycles before pulling CS high. If the
last 2 bits of the setup register are 00 or 01, neither the
unipolar mode register nor the bipolar mode register is
written. Any subsequent byte is recognized as a new
input data byte. See Tables 4 and 5 to program the
unipolar and bipolar mode registers.
If a channel is configured as both unipolar and bipolar,
the unipolar setting takes precedence. In unipolar
mode, AIN+ can exceed AIN- by up to VREF. The out-
put format in unipolar mode is binary. In bipolar mode,
either input can exceed the other by up to VREF / 2. The
output format in bipolar mode is two's complement.
Averaging Register
Write to the averaging register to configure the ADC to
average up to 32 samples for each requested result,
and to independently control the number of results
requested for single-channel scans.
Table 2 details the four scan modes available in the con-
version register. All four scan modes allow averaging as
long as the AVGON bit, bit 4 in the averaging register, is
BIT
NAME
BIT
FUNCTION
—
7 (MSB) Set to 1 to select conversion register.
CHSEL3
6
Analog input channel select.
CHSEL2
5
Analog input channel select.
CHSEL1
4
Analog input channel select.
CHSEL0
3
Analog input channel select.
SCAN1
2
Scan mode select.
SCAN0
1
Scan mode select.
TEMP
0 (LSB)
Set to 1 to take a single temperature
measurement. The first conversion result
of a scan contains temperature information.
Table 2. Conversion Register*
*See below for bit details.
CHSEL3
CHSEL2
CHSEL1
CHSEL0
SELECTED
CHANNEL (N)
0
AIN0
0
1
AIN1
0
1
0
AIN2
0
1
AIN3
0
1
0
AIN4
0
1
0
1
AIN5
0
1
0
AIN6
0
1
AIN7
1
0
AIN8
1
0
1
AIN9
1
0
1
0
AIN10
1
0
1
AIN11
1
0
AIN12
1
0
1
AIN13
1
0
AIN14
1
AIN15
SCAN1 SCAN0
SCAN MODE (CHANNEL N IS
SELECTED BY BITS CHSEL3–CHSEL0)
0
Scans channels 0 through N.
01
Scans channels N through the highest
numbered channel.
10
Scans channel N repeatedly. The averaging
register sets the number of results.
1
No scan. Converts channel N once only.
相關PDF資料 |
PDF描述 |
|---|---|
| MAX1110EAP | +2.7V, Low-Power, Multichannel, Serial 8-Bit ADCs |
| MAX1185ECM+ | 2-CH 10-BIT FLASH METHOD ADC, PARALLEL ACCESS, PQFP48 |
| MAX1300AEUG | 8-CH 16-BIT SUCCESSIVE APPROXIMATION ADC, SERIAL ACCESS, PDSO24 |
| MAX1300BEUG+ | 8-CH 16-BIT SUCCESSIVE APPROXIMATION ADC, SERIAL ACCESS, PDSO24 |
| MAX13208EALB-T | UNIDIRECTIONAL, SILICON, TVS DIODE |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MAX1029AEEP | 功能描述:模數轉換器 - ADC RoHS:否 制造商:Texas Instruments 通道數量:2 結構:Sigma-Delta 轉換速率:125 SPs to 8 KSPs 分辨率:24 bit 輸入類型:Differential 信噪比:107 dB 接口類型:SPI 工作電源電壓:1.7 V to 3.6 V, 2.7 V to 5.25 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:VQFN-32 |
| MAX1029AEEP+ | 功能描述:模數轉換器 - ADC Integrated Circuits (ICs) RoHS:否 制造商:Texas Instruments 通道數量:2 結構:Sigma-Delta 轉換速率:125 SPs to 8 KSPs 分辨率:24 bit 輸入類型:Differential 信噪比:107 dB 接口類型:SPI 工作電源電壓:1.7 V to 3.6 V, 2.7 V to 5.25 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:VQFN-32 |
| MAX1029AEEP+T | 功能描述:模數轉換器 - ADC Integrated Circuits (ICs) RoHS:否 制造商:Texas Instruments 通道數量:2 結構:Sigma-Delta 轉換速率:125 SPs to 8 KSPs 分辨率:24 bit 輸入類型:Differential 信噪比:107 dB 接口類型:SPI 工作電源電壓:1.7 V to 3.6 V, 2.7 V to 5.25 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:VQFN-32 |
| MAX1029AEEP-T | 功能描述:模數轉換器 - ADC RoHS:否 制造商:Texas Instruments 通道數量:2 結構:Sigma-Delta 轉換速率:125 SPs to 8 KSPs 分辨率:24 bit 輸入類型:Differential 信噪比:107 dB 接口類型:SPI 工作電源電壓:1.7 V to 3.6 V, 2.7 V to 5.25 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:VQFN-32 |
| MAX1029BCEP | 功能描述:模數轉換器 - ADC RoHS:否 制造商:Texas Instruments 通道數量:2 結構:Sigma-Delta 轉換速率:125 SPs to 8 KSPs 分辨率:24 bit 輸入類型:Differential 信噪比:107 dB 接口類型:SPI 工作電源電壓:1.7 V to 3.6 V, 2.7 V to 5.25 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:VQFN-32 |
發布緊急采購，3分鐘左右您將得到回復。