- 您現在的位置：買賣IC網 > PDF目錄45052 > M8803F3W-15K1 (STMICROELECTRONICS) 1M X 1 FLASH, 27 I/O, PIA-GENERAL PURPOSE, PQCC52 PDF資料下載
參數資料
| 型號： | M8803F3W-15K1 |
| 廠商： | STMICROELECTRONICS |
| 元件分類： | 微控制器/微處理器 |
| 英文描述： | 1M X 1 FLASH, 27 I/O, PIA-GENERAL PURPOSE, PQCC52 |
| 封裝： | PLASTIC, LCC-52 |
| 文件頁數： | 49/85頁 |
| 文件大?。?/td> | 601K |
| 代理商： | M8803F3W-15K1 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁當前第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁第77頁第78頁第79頁第80頁第81頁第82頁第83頁第84頁第85頁
53/85
M88 FAMILY
Table 39. Operating Range
Table 40. Recommended Operating Condi tions
Range
Temperature
VCC
VCC Tolerance
–90
–15
Commercial
0
° Cto +70°C+ 5 V
± 10%
Industrial
–40
° Cto +85°C+ 5 V
± 10%
Commercial
0
° C to +70°C
+ 3 V
+20/–10%
Industrial
–40
° Cto +85°C
+ 3 V
+20/–10%
Symbol
Parameter
Condition
Min.
Typ.
Max.
Unit
VCC
Supply Voltage
M88x3FxY
4.5
5
5.5
V
VCC
Supply Voltage
M88x3FxW
2.7
3
3.6
V
power-up. While the reset input is active, the PLD
is active and the outputs are determined by the
PSDabel equations. The chip status during reset
and Power Down Mode is shown in Table 36. The
reset input will not abort any active programming
or erase cycles in the main Flash or Boot block.
Programming In-Circuit using the JTAG
Interface
The
JTAG
interface
on
the
M88x3Fxx
FLASH+PSD can be enabled on Port C (see Table
37). All memory (Flash and EEPROM), PLD logic,
and PSD configuration bits may be programmed
through the JTAG interface. A blank part can be
mounted
on
a
printed
circuit
board
and
programmed using JTAG.
The standard JTAG signals (IEEE 1149.1) are
TMS, TCK, TDI, and TDO. Two additional signals,
TSTAT and TERR, are optional JTAG extensions
used to speed up program and erase operations.
By default, on a blank PSD, four pins on Port C are
enabled for the basic JTAG signals TMS, TCK,
TDI, and TDO.
See Application Note AN1153 for more details on
JTAG In-System-Programming.
Standard JTAG Signals
The standard JTAG signals (TMS, TCK, TDI, and
TDO) can be enabled by any of three different
conditions that are logically ORed. When enabled,
TDI, TDO, TCK, and TMS are inputs, waiting for a
serial command from an external JTAG controller
device (such as FlashLink or Automated Test
Equipment). When the enabling command is
received, TDO becomes an output and the JTAG
channel is fully functional inside the PSD. The
same command that enables the JTAG channel
may optionally enable the two additional JTAG
pins, TSTAT and TERR.
The following symbolic logic equation specifies the
conditions enabling the four basic JTAG pins
(TMS, TCK, TDI, and TDO) on their respective
Port C pins. For purposes of discussion, the logic
label JTAG_ON will be used. When JTAG_ON is
true, the four pins are enabled for JTAG. When
JTAG_ON is false, the four pins can be used for
general PSD I/O.
JTAG_ON = PSDsoft_enabled
+
/* An NVM configuration bit inside the
PSD
is
set
by
the
designer
in
the
PSDsoft
Configuration
utility.
This
dedicates
the
pins
for
JTAG
at
all
times (compliant with IEEE 1149.1 */
Microcontroller_enabled
+
/* The microcontroller can set a bit at
run-time
by
writing
to
the
PSD
register,
JTAG
Enable.
This
register
is
located
at
address
CSIOP
+ offset
C7h.
Setting
the
JTAG_ENABLE
bit
in
this register will enable the pins for
JTAG use. This bit is cleared by a PSD
reset
or
the
microcontroller.
See
Table 38 for bit definition. */
PSD_product_term_enabled;
/* A dedicated product term (PT) inside
the PSD can be used to enable the JTAG
pins.
This
PT
has
the
reserved
name
JTAGSEL.
Once
defined
as
a
node
in
PSDabel,
the
designer
can
write
an
equation
for
JTAGSEL.
This
method
is
used
when
the
Port
C
JTAG
pins
are
multiplexed with other I/O signals. It
is
recommended
to
logically
tie
the
node JTAGSEL to the JEN\ signal on the
Flashlink cable when multiplexing JTAG
signals. See Application Note 1153 for
details. */
The M88x3Fxx FLASH+PSD supports JTAG In-
System-Configuration (ISC) commands, but not
Boundary Scan. A definition of these JTAG-ISC
commands and sequences are defined in a
supplemental document available from ST. ST’s
PSDsoft software tool and FlashLink JTAG
相關PDF資料 |
PDF描述 |
|---|---|
| M8803F2W-15T1 | 1M X 1 FLASH, 27 I/O, PIA-GENERAL PURPOSE, PQFP52 |
| M8813F3W-15K1 | 1M X 1 FLASH, 27 I/O, PIA-GENERAL PURPOSE, PQCC52 |
| M8813F3Y-90K1 | 1M X 1 FLASH, 27 I/O, PIA-GENERAL PURPOSE, PQCC52 |
| M8813F3Y-90T1 | 1M X 1 FLASH, 27 I/O, PIA-GENERAL PURPOSE, PQFP52 |
| M8803F3Y-90K1T | 1M X 1 FLASH, 27 I/O, PIA-GENERAL PURPOSE, PQCC52 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| M8805/100-007 | 制造商:OTTO Engineering Inc 功能描述:M8805/100-007 |
| M8805/100-009 | 制造商:OTTO Engineering Inc 功能描述:M8805/100-009 |
| M8805/100-010 | 制造商:OTTO Engineering Inc 功能描述:M8805/100-010 |
| M8805/100-015 | 制造商:OTTO Engineering Inc 功能描述:M8805/100-015 |
| M8805/100-016 | 制造商:OTTO Engineering Inc 功能描述:M8805/100-016 |
發布緊急采購，3分鐘左右您將得到回復。