- 您現在的位置：買賣IC網 > PDF目錄370967 > M54687FP (Mitsubishi Electric Corporation) Bi-DIRECTIONAL MOTOR DRIVER WITH GOVERNOR PDF資料下載
參數資料
| 型號： | M54687FP |
| 廠商： | Mitsubishi Electric Corporation |
| 英文描述： | Bi-DIRECTIONAL MOTOR DRIVER WITH GOVERNOR |
| 中文描述： | 雙電機驅動器，帶有定向總督 |
| 文件頁數： | 5/6頁 |
| 文件大?。?/td> | 133K |
| 代理商： | M54687FP |
Bi-DIRECTIONAL MOTOR DRIVER WITH GOVERNOR
M54687FP
MITSUBISHI <CONTROL / DRIVER IC>
(3) Speed Control Method III (to increase the precision of forward
rotation and reverse rotation)
The above two applications cannot make fine adjustments in
forward rotation and reverse rotation (because the external
resistance is shared with the forward rotation and reverse rotation).
Fine adjustments can be made for each of forward rotation and
reverse rotation if the external circuit is set as shown in the drawing
above.
This external circuit is also available to change the speed of
forward and reverse rotation.
The control method adopts the same formula as formula (1).
However, the following relations must be satisfied:
RT+RS
RS1 or RS2
RT
RT1 or RT2
Speed Control Method
(1) Speed Control Method I (See the application circuit drawing.)
For PLAY/REV
Rotation number can be expressed by the following formula:
N=
{IB
RT+V
ref
(1)
Where:
Motor generation constant: Ka, Motor armature resistance: Ra,
Rotation number: N
K: Current proportional constant, IB: PSC pin bias current,
Ia:motor current
RT, RS: External resistance
In addition, to set the rotation number with RS, external
resistance RT is generally set as follows:
RT K x Ra
For FF/REW
Note that the rotation number is basically controlled with the
same expression as formula (1) but different reference voltage
V
ref
and different bias current IB are to be used.
However, V
ref
5VR+0.5
=
(2) Speed Control Method II (to increase the motor rotation number)
In the external circuit above, the voltage across motors is almost
determined by the ratio of ‘RS+RT’ to ‘RT’ and, therefore, a value
set for the voltage across motors is not so large.
As method (1) of speed control I, the rotation number can be
controlled.
However, the following relations must be satisfied:
RT
RT+RS
RS+RT
RT
V
CC
RT
RT+RS
RT
K
1
Ka
V
R
PSC2
PSC1
O
1
O
2
R
L
S
L-G
P-G
Control signal
M
Control signal
V
CC
V
R
PSC2
PSC1
O
1
O
2
R
L
S
L-G
P-G
M
RT1
RS1
RS2
RT2
RS
RT
RT
(1+
)+la(
-Ra)}
相關PDF資料 |
PDF描述 |
|---|---|
| M54910P | F2F MAGNETIC STRIPE ENCORDING CARD READER |
| M54914FP | F2F MAGNETIC STRIPE ENCORDING CARD READER |
| M54965ASP | SERIAL INPUT PLL FREQUENCY SYNTHESIZER FOR VTR |
| M54972 | Bi-CMOS 8-BIT SERIAL-INPUT LATCHED DRIVER |
| M54972FP | Bi-CMOS 8-BIT SERIAL-INPUT LATCHED DRIVER |
相關代理商/技術參數 |
參數描述 |
|---|---|
| M54687FP(#TG0G) | 制造商:Renesas Electronics Corporation 功能描述: |
| M5474GFE | 功能描述:模塊化系統 - SOM M5474 FIRE ENGINE RoHS:否 制造商:Digi International 外觀尺寸:ConnectCore 9P 處理器類型:ARM926EJ-S 頻率:150 MHz 存儲容量:8 MB, 16 MB 存儲類型:NOR Flash, SDRAM 接口類型:I2C, SPI, UART 工作電源電壓:3.3 V 最大工作溫度:+ 85 C 尺寸:1.97 in x 1.97 in x 6.1 in |
| M5474HC564 | 制造商:STMICROELECTRONICS 制造商全稱:STMicroelectronics 功能描述:OCTAL D-TYPE FLIP FLOP WITH 3 STATE OUTPUT HC564 INVERTING - HC574 NON INVERTING |
| M5474HC574 | 制造商:STMICROELECTRONICS 制造商全稱:STMicroelectronics 功能描述:OCTAL D-TYPE FLIP FLOP WITH 3 STATE OUTPUT HC564 INVERTING - HC574 NON INVERTING |
| M5474LITEKIT | 功能描述:開發板和工具包 - COLDFIRE LOW COST KIT FOR MCF547X RoHS:否 制造商:Freescale Semiconductor 產品:Development Kits 工具用于評估:MCF53017 核心:ColdFire V3 接口類型:Ethernet, UART, USB 工作電源電壓:12 V |
發布緊急采購，3分鐘左右您將得到回復。