- 您現在的位置：買賣IC網 > PDF目錄370965 > M52745SP (Mitsubishi Electric Corporation) BUS CONTROLLED 3-CHANNEL VIDEO PREAMP FOR CRT DISPLAY MONITOR PDF資料下載
參數資料
| 型號： | M52745SP |
| 廠商： | Mitsubishi Electric Corporation |
| 英文描述： | BUS CONTROLLED 3-CHANNEL VIDEO PREAMP FOR CRT DISPLAY MONITOR |
| 中文描述： | 總線控制的陰極射線管顯示屏三通道視頻前置放大器 |
| 文件頁數： | 8/21頁 |
| 文件大?。?/td> | 386K |
| 代理商： | M52745SP |
MITSUBISHI ICs (Monitor)
M52745SP
BUS CONTROLLED 3-CHANNEL VIDEO PREAMP FOR CRT DISPLAY MONITOR
8
F
C1
Frequency characteristics1 (f=50MHz)
First, SG3 to 1MHz is as input signal. Input a resister that is about
2k‰to offer the voltage at input pins (6, 9, 11) in order that the bot-
tom of input signal is 2.5V. Control the main contrast in order that
the amplitude of sine wave output is 4.0V
P-P
. Control the brightness
in order that the bottom of sine wave output is 2.0V
P-P
. By the same
way, measure the output amplitude when SG3 to 50MHz is as input
signal. The measured value is called VOUT (24, 28, 31). Frequency
characteristics F
C1
(24, 28, 31 ) is calculated by the equation below:
F
C1
Frequency relative characteristics1 (f=50MHz)
Relative characteristics F
C1
is calculated by the difference in the
output between the channels.
F
C1
' Frequency characteristics1 (f=150MHz)
Measuring condition and procedure are the same as described in
table, expect SG3 to 150MHz.
F
C1
' Frequency relative characteristics1 (f=150MHz)
Relative characteristics F
C1
' is calculated by the difference in the
output between the channels.
F
C2
Frequency characteristics2 (f=150MHz)
SG3 to 1MHz is as input signal. Control the main contrast in order
that the amplitude of sine wave output is 1.0V
P-P
. By the same way,
measure the output amplitude when SG3 to 150MHz is as input
signal.
The measured value is called VOUT (24, 28, 31). Frequency
characteristics F
C2
(24, 28, 31) is calculated by the equation below:
F
C2
Frequency relative characteristics2
(f=150MHz)
Relative characteristics F
C2
is calculated by the difference in the
output between the channels.
C.T.1 Crosstalk1 (f=50MHz)
Input SG3 (50MHz) to pin2 only, and then measure the waveform
amplitude output at OUT (24, 28, 31). The measured value is called
VOUT (24, 28, 31). Crosstalk C.T.1 is calculated by the equation
below:
C.T.1' Crosstalk1 (f=150MHz)
Measuring condition and procedure are the same as described in
C.T.1, expect SG3 to 150MHz.
C.T.2 Crosstalk2 (f=50MHz)
Input SG3 (50MHz) to pin6 only, and then measure the waveform
amplitude output at OUT (24, 28, 31). The measured value is called
VOUT (24, 28, 31). Crosstalk C.T.2 is calculated by the equation
below:
C.T.2' Crosstalk2 (f=150MHz)
Measuring condition and procedure are the same as described in
C.T.2, expect SG3 to 150MHz.
C.T.3 Crosstalk3 (f=50MHz)
Input SG3 (50MHz) to pin11 only, and then measure the waveform
amplitude output at OUT (24, 28, 31). The measured value is called
VOUT (24, 28, 31). Crosstalk C.T.3 is calculated by the equation
below:
C.T.3' Crosstalk3 (f=150MHz)
Measuring condition and procedure are the same as described in
C.T.3, expect SG3 to 150MHz.
Tr Pulse characteristics1 (4V
P-P
)
Control the main contrast (00H) in order that the amplitude of output
signal is 4.0V
P-P
.
Control the brightness (V1) in order that the Black level of output
signal is 2.0V.
Measure the time needed for the input pulse to rise from 10% to 90
% (Tr1) and for the output pulse to rise from 10% to 90% (Tr2) with
an active probe.
Pulse characteristics Tr is calculated by the equations below :
Tr Relative pulse characteristics1
Relative characteristics Tr is calculated by the difference in the
output between the channels.
Tf Pulse characteristics2 (4V
P-P
)
Measure the time needed for the input pulse to fall from 90% to 10%
(Tf1) and for the output pulse to fall from 90% to 10% (Tf2) with an
active prove.
Pulse characteristics Tf is calculated by the equations below :
F
C1
=20log
(dB)
VOUT V
P-P
Output amplitude when inputted SG3 (1MHz):4V
P-P
F
C2
=20log
(dB)
VOUT V
P-P
Output amplitude when inputted SG3 (1MHz):4V
P-P
C.T.1=20 log
VOUT (24, 31)
VOUT (28)
(dB)
C.T.2=20 log
VOUT (24, 31)
VOUT (28)
(dB)
C.T.3=20 log
VOUT (28, 31)
VOUT (24)
(dB)
Tr = [(Tr2)
2
-(Tr1)
2
]
Tf = [(Tf2)
2
-(Tf1)
2
]
PRELIMINARY
Some parametric limits are subject to change.
相關PDF資料 |
PDF描述 |
|---|---|
| M52746SP | BUS CONTROLLED 3CH VIDEO PRE-AMP FOR CRT DISPLAY MONITOR |
| M52749FP | BUS CONTROLLED 3CH VIDEO PRE-AMP FOR CRT DISPLAY MONITOR |
| M52755FP | WIDE BAND ANALOG SWITCH |
| M52756SP | WIDE BAND ANALOG SWITCH |
| M52756 | WIDE BAND ANALOG SWITCH |
相關代理商/技術參數 |
參數描述 |
|---|---|
| M52746SP | 制造商:MITSUBISHI 制造商全稱:Mitsubishi Electric Semiconductor 功能描述:BUS CONTROLLED 3CH VIDEO PRE-AMP FOR CRT DISPLAY MONITOR |
| M52749FP | 制造商:RENESAS 制造商全稱:Renesas Technology Corp 功能描述:BUS Controlled 3ch Video Pre-amp for CRT Display Monitor |
| M527534-12 | 制造商:ITT 制造商全稱:ITT Industries 功能描述:Cannon MIL-DTL-38999 Connectors |
| M52755FP | 制造商:MITSUBISHI 制造商全稱:Mitsubishi Electric Semiconductor 功能描述:WIDE BAND ANALOG SWITCH |
| M52755SP | 制造商:Panasonic Industrial Company 功能描述:IC |
發布緊急采購，3分鐘左右您將得到回復。