- 您現在的位置：買賣IC網 > PDF目錄296402 > M50FW016N1G (意法半導體) 16 Mbit 2Mb x8, Uniform Block 3V Supply Firmware Hub Flash Memory PDF資料下載
參數資料
| 型號： | M50FW016N1G |
| 廠商： | 意法半導體 |
| 英文描述： | 16 Mbit 2Mb x8, Uniform Block 3V Supply Firmware Hub Flash Memory |
| 中文描述： | 16兆位的2Mb × 8，統一座3V電源閃存固件集線器 |
| 文件頁數： | 15/45頁 |
| 文件大?。?/td> | 673K |
| 代理商： | M50FW016N1G |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁當前第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁
M50FW016
22/45
FIRMWARE HUB (FWH) INTERFACE CONFIGURATION REGISTERS
When the Firmware Hub Interface is selected sev-
eral additional registers can be accessed. These
registers control the protection status of the
Blocks, read the General Purpose Input pins and
identify the memory using the Electronic Signature
codes. See Table 12. for the memory map of the
Configuration Registers in the FWH Protocol.
Lock Registers
The Lock Registers control the protection status of
the Blocks. Each Block has its own Lock Register.
Three bits within each Lock Register control the
protection of each block, the Write Lock Bit, the
Read Lock Bit and the Lock Down Bit.
The Lock Registers can be read and written,
though care should be taken when writing as, once
the Lock Down Bit is set, ‘1’, further modifications
to the Lock Register cannot be made until cleared,
to ‘0’, by a reset or power-up.
See Table 13. for details on the bit definitions of
the Lock Registers.
Write Lock. The
Write
Lock
Bit
determines
whether the contents of the Block can be modified
(using the Program or Block Erase Command).
When the Write Lock Bit is set, ‘1’, the block is
write protected; any operations that attempt to
change the data in the block will fail and the Status
Register will report the error. When the Write Lock
Bit is reset, ‘0’, the block is not write protected
through the Lock Register and may be modified
unless write protected through some other means.
When VPP is less than VPPLK all blocks are pro-
tected and cannot be modified, regardless of the
state of the Write Lock Bit. If Top Block Lock, TBL,
is Low, VIL, then the Top Block (Block 31) is write
protected and cannot be modified. Similarly, if
Write Protect, WP, is Low, VIL, then the Main
Blocks (Blocks 0 to 30) are write protected and
cannot be modified.
After power-up or reset the Write Lock Bit is al-
ways set to ‘1’ (write protected).
Read Lock. The
Read
Lock
bit
determines
whether the contents of the Block can be read
(from Read mode). When the Read Lock Bit is set,
‘1’, the block is read protected; any operation that
attempts to read the contents of the block will read
00h instead. When the Read Lock Bit is reset, ‘0’,
read operations in the Block return the data pro-
grammed into the block as expected.
After power-up or reset the Read Lock Bit is al-
ways reset to ‘0’ (not read protected).
Lock Down. The Lock Down Bit provides a
mechanism for protecting software data from sim-
ple hacking and malicious attack. When the Lock
Down Bit is set, ‘1’, further modification to the
Write Lock, Read Lock and Lock Down Bits cannot
be performed. A reset or power-up is required be-
fore changes to these bits can be made. When the
Lock Down Bit is reset, ‘0’, the Write Lock, Read
Lock and Lock Down Bits can be changed.
Firmware Hub (FWH) General Purpose Input
Register
The Firmware Hub (FWH) General Purpose Input
Register holds the state of the Firmware Hub Inter-
face General Purpose Input pins, FGPI0-FGPI4.
When this register is read, the state of these pins
is returned. This register is read-only and writing to
it has no effect.
The signals on the Firmware Hub Interface Gener-
al Purpose Input pins should remain constant
throughout the whole Bus Read cycle in order to
guarantee that the correct data is read.
Manufacturer Code Register
Reading the Manufacturer Code Register returns
the manufacturer code for the memory. The man-
ufacturer code for STMicroelectronics is 20h. This
register is read-only and writing to it has no effect.
Device Code Register
Reading the Device Code Register returns the de-
vice code for the memory, 2Eh. This register is
read-only and writing to it has no effect.
Multi-Byte Read/Write Configuration Registers
The Multi-Byte Read/Write Configuration Regis-
ters contain information as which multi-byte read
and write access sizes will be accepted. The
M50FW016 supports 4/16/128-byte reading and
4-byte writing.
相關PDF資料 |
PDF描述 |
|---|---|
| M50FW016N1TG | 16 Mbit 2Mb x8, Uniform Block 3V Supply Firmware Hub Flash Memory |
| M50FW016N5 | 16 Mbit 2Mb x8, Uniform Block 3V Supply Firmware Hub Flash Memory |
| M50FW016N5G | 16 Mbit 2Mb x8, Uniform Block 3V Supply Firmware Hub Flash Memory |
| M50FW080K1 | 8 Mbit 1Mb x8, Uniform Block 3V Supply Firmware Hub Flash Memory |
| M50FW080K1G | 8 Mbit 1Mb x8, Uniform Block 3V Supply Firmware Hub Flash Memory |
相關代理商/技術參數 |
參數描述 |
|---|---|
| M50FW016N1T | 制造商:STMICROELECTRONICS 制造商全稱:STMicroelectronics 功能描述:16 Mbit 2Mb x8, Uniform Block 3V Supply Firmware Hub Flash Memory |
| M50FW016N1TG | 制造商:STMICROELECTRONICS 制造商全稱:STMicroelectronics 功能描述:16 Mbit 2Mb x8, Uniform Block 3V Supply Firmware Hub Flash Memory |
| M50FW016N5 | 制造商:STMICROELECTRONICS 制造商全稱:STMicroelectronics 功能描述:16 Mbit 2Mb x8, Uniform Block 3V Supply Firmware Hub Flash Memory |
| M50FW016N5G | 功能描述:閃存 SERIAL FLASH RoHS:否 制造商:ON Semiconductor 數據總線寬度:1 bit 存儲類型:Flash 存儲容量:2 MB 結構:256 K x 8 定時類型: 接口類型:SPI 訪問時間: 電源電壓-最大:3.6 V 電源電壓-最小:2.3 V 最大工作電流:15 mA 工作溫度:- 40 C to + 85 C 安裝風格:SMD/SMT 封裝 / 箱體: 封裝:Reel |
| M50FW016N5T | 制造商:STMICROELECTRONICS 制造商全稱:STMicroelectronics 功能描述:16 Mbit 2Mb x8, Uniform Block 3V Supply Firmware Hub Flash Memory |
發布緊急采購，3分鐘左右您將得到回復。