參數資料
型號： M41T93ZMY6F
廠商： STMICROELECTRONICS
元件分類： 時鐘/數據恢復及定時提取
英文描述： 1 TIMER(S), REAL TIME CLOCK, PDSO18
封裝： 0.300 INCH, ROHS COMPLIANT, PLASTIC, SOP-18
文件頁數： 13/49頁
文件大?。?/td> 719K
代理商： M41T93ZMY6F
Clock operation
M41T93
Doc ID 12615 Rev 5
3.4
Clock calibration
The M41T93 oscillator is designed for use with a 12.5 pF crystal load capacitance. When
the calibration circuit is properly employed, accuracy improves to better than ±1 ppm at
25 °C.
The M41T93 design provides the following two methods for clock error correction.
3.4.1
Digital calibration (periodic counter correction)
This method employs the use of periodic counter correction by adjusting the ratio of the
100 Hz divider stage to the 512 Hz divider stage. Under normal operation, the 100Hz divider
stage outputs precisely 100 pulses for every 512 pulses of the 512 Hz input stage to provide
the input frequency to the fraction of seconds clock register. By adjusting the number of
512 Hz input pulses used to generate 100 output pulses, the clock can be sped up or slowed
down, as shown in Figure 12 on page 25.
When a non-zero value is loaded into the five calibration bits (DC4 – DC0) found in the
digital calibration register (08h) and the sign bit is ‘1,’ (indicating positive calibration), the
100 Hz stage outputs 100 pulses for every 511 input pulses instead of the normal 512.
Since the 100 pulses are now being output in a shorter window, this has the effect of
speeding up the clock by 1/512 seconds for each second the circuit is active. Similarly, when
the sign bit is ‘0,’ indicating negative calibration, the block outputs 100 pulses for every 513
input pulses. Since the 100 pulses are then being output in a longer window, this has the
effect of slowing down the clock by 1/512 seconds for each second the circuit is active.
The amount of calibration is controlled by using the value in the calibration register (N) to
generate the adjustment in one second increments. This is done for the first N seconds once
every eight minutes for positive calibration, and for N seconds once every sixteen minutes
for negative calibration (see Table 4 on page 21).
For example, if the calibration register is set to '100010,' then the adjustment will occur for
two seconds in every minute. Similarly, if the calibration register is set to '000011,' then the
adjustment will occur for 3 seconds in every alternating minute.
The digital calibration bits (DC4 – DC0) occupy the five lower order bits in the digital
calibration register (08h). These bits can be set to represent any value between 0 and 31 in
binary form. The sixth bit (DCS) is a sign bit; '1' indicates positive calibration, '0' indicates
negative calibration. Calibration occurs within an 8-minute (positive) or 16-minute (negative)
cycle. Therefore, each calibration step has an effect on clock accuracy of +4.068 or –2.034
ppm. Assuming that the oscillator is running at exactly 32,768 Hz, each of the 31 increments
in the calibration byte would represent +10.7 or –5.35 seconds per month, which
corresponds to a total range of +5.5 or –2.75 minutes per month.
Note:
1
The modified pulses are not observable on the frequency test (FT) output, nor will the effect
of the calibration be measurable real-time, due to the periodic nature of the error
compensation.
2
Positive digital calibration is performed on an eight minute cycle, therefore the value in the
calibration register should not be modified more frequently than once every eight minutes for
positive values of calibration. Negative digital calibration is performed on a sixteen minute
cycle, therefore negative values in the calibration register should not be modified more
frequently than once every sixteen minutes.
相關PDF資料
PDF描述
M41T93ZQA6F 1 TIMER(S), REAL TIME CLOCK, PQCC16
M41T93RQA6F 1 TIMER(S), REAL TIME CLOCK, PQCC16
M41T93SQA6F 1 TIMER(S), REAL TIME CLOCK, PQCC16
M43C505-XXX-DIT 4-BIT, MROM, 2 MHz, MICROCONTROLLER, UUC
M43C505-XXX-Q44 4-BIT, MROM, 2 MHz, MICROCONTROLLER, PQCC44
相關代理商/技術參數
參數描述
M41T93ZQA6E 制造商:STMICROELECTRONICS 制造商全稱:STMicroelectronics 功能描述:Serial SPI bus RTC with battery switchover
M41T93ZQA6F 功能描述:實時時鐘 Serial SPI bus RTC RoHS:否 制造商:Microchip Technology 功能:Clock, Calendar. Alarm RTC 總線接口:I2C 日期格式:DW:DM:M:Y 時間格式:HH:MM:SS RTC 存儲容量:64 B 電源電壓-最大:5.5 V 電源電壓-最小:1.8 V 最大工作溫度:+ 85 C 最小工作溫度: 安裝風格:Through Hole 封裝 / 箱體:PDIP-8 封裝:Tube
M41T94 制造商:STMICROELECTRONICS 制造商全稱:STMicroelectronics 功能描述:512 Bit 64 bit x8 SERIAL RTC SPI SRAM
M41T94_06 制造商:STMICROELECTRONICS 制造商全稱:STMicroelectronics 功能描述:Serial Real Time Clock with 44Bytes NVRAM and Reset
M41T94_07 制造商:STMICROELECTRONICS 制造商全稱:STMicroelectronics 功能描述:Serial real-time clock with 44 bytes NVRAM and reset
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*