- 您現在的位置：買賣IC網 > PDF目錄102740 > M41T93RMY6E (STMICROELECTRONICS) 1 TIMER(S), REAL TIME CLOCK, PDSO18 PDF資料下載
參數資料
| 型號： | M41T93RMY6E |
| 廠商： | STMICROELECTRONICS |
| 元件分類： | 時鐘/數據恢復及定時提取 |
| 英文描述： | 1 TIMER(S), REAL TIME CLOCK, PDSO18 |
| 封裝： | 0.300 INCH, ROHS COMPLIANT, PLASTIC, SOP-18 |
| 文件頁數： | 19/49頁 |
| 文件大?。?/td> | 719K |
| 代理商： | M41T93RMY6E |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁當前第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁
Clock operation
M41T93
Doc ID 12615 Rev 5
Figure 13.
Crystal isolation example
Note:
The substrate pad should be tied to VSS.
3.5
Setting the alarm clock registers
Address locations 0Ah-0Eh (alarm 1) and 14h-18h (alarm 2) contain the alarm settings.
Either alarm can be configured independently to go off at a prescribed time on a specific
month, date, hour, minute, or second, or repeat every year, month, day, hour, minute, or
second. Bits RPT15–RPT11 and RPT25-RPT21 put the alarms in the repeat mode of
operation. Table6 on page27 shows the possible bit configurations.
Codes not listed in the table default to the once-per-second mode to quickly alert the user of
an incorrect alarm setting. When the clock information matches the alarm clock settings
based on the match criteria defined by RPT15–RPT11 and/or RPT25-RPT21, AF1 (alarm 1
flag) or AF2 (alarm 2 flag) is set. If A1IE (alarm 1 interrupt enable) is set, the alarm condition
activates the IRQ/FT/OUT output pin. To disable either of the alarms, write a '0' to the alarm
date registers and to the RPTx5–RPTx1 bits.
Note:
If the address pointer is allowed to increment to the flag register address, or the last address
written is “Alarm Seconds,” the address pointer will increment to the flag address, and an
alarm condition will not cause the interrupt/flag to occur until the address pointer is moved to
a different address.
The IRQ output is cleared by a READ to the flags register (0Fh) as shown in Figure 14. A
subsequent READ of the flags register is necessary to see that the value of the alarm flag
has been reset to '0.'.
The IRQ/FT/OUT pin can also be activated in the battery backup mode (see Figure 15 on
page 27).
AI11814
Crystal
XI XO
VSS
Local Grounding
Plane (Layer 2)
相關PDF資料 |
PDF描述 |
|---|---|
| MN101CA5F | 8-BIT, MROM, 20 MHz, MICROCONTROLLER, PQFP112 |
| MC68HC908QY8MDTE | 8-BIT, FLASH, 32 MHz, MICROCONTROLLER, PDSO16 |
| MC9S12C64MFAE25 | 16-BIT, FLASH, 25 MHz, MICROCONTROLLER, PQFP48 |
| MC312XDP512F0VAG | 16-BIT, FLASH, 40 MHz, MICROCONTROLLER, PQFP144 |
| MC912XDP512F0CAA | 16-BIT, FLASH, 40 MHz, MICROCONTROLLER, PQFP80 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| M41T93RMY6F | 功能描述:實時時鐘 Serial SPI bus RTC RoHS:否 制造商:Microchip Technology 功能:Clock, Calendar. Alarm RTC 總線接口:I2C 日期格式:DW:DM:M:Y 時間格式:HH:MM:SS RTC 存儲容量:64 B 電源電壓-最大:5.5 V 電源電壓-最小:1.8 V 最大工作溫度:+ 85 C 最小工作溫度: 安裝風格:Through Hole 封裝 / 箱體:PDIP-8 封裝:Tube |
| M41T93RMY6F-CUT TAPE | 制造商:ST 功能描述:M41T93 Series 5.5 V Serial SPI Bus RTC with Battery Switchover - SOX-18 |
| M41T93RQA6E | 制造商:STMICROELECTRONICS 制造商全稱:STMicroelectronics 功能描述:Serial SPI bus RTC with battery switchover |
| M41T93RQA6F | 功能描述:實時時鐘 SPI RTC 32.768 kHz 365nA 2.0V to 5.5V RoHS:否 制造商:Microchip Technology 功能:Clock, Calendar. Alarm RTC 總線接口:I2C 日期格式:DW:DM:M:Y 時間格式:HH:MM:SS RTC 存儲容量:64 B 電源電壓-最大:5.5 V 電源電壓-最小:1.8 V 最大工作溫度:+ 85 C 最小工作溫度: 安裝風格:Through Hole 封裝 / 箱體:PDIP-8 封裝:Tube |
| M41T93RQA6F-CUT TAPE | 制造商:ST 功能描述:M41T93 Series 5.5 V Serial SPI Bus RTC With Battery Switchover -QFN-16 |
發布緊急采購，3分鐘左右您將得到回復。