參數資料
型號： M41ST85YMH6TR
廠商： STMICROELECTRONICS
元件分類： 時鐘/數據恢復及定時提取
英文描述： 1 TIMER(S), REAL TIME CLOCK, PDSO28
封裝： 0.330 INCH, SNAPHAT, PLASTIC, SOH-28
文件頁數： 9/34頁
文件大?。?/td> 532K
代理商： M41ST85YMH6TR
17/34
M41ST85Y, M41ST85W
Setting Alarm Clock Registers
Address locations 0Ah-0Eh contain the alarm set-
tings. The alarm can be configured to go off at a
prescribed time on a specific month, date, hour,
minute, or second, or repeat every year, month,
day, hour, minute, or second. It can also be pro-
grammed to go off while the M41ST85Y/W is in the
battery back-up to serve as a system wake-up call.
Bits RPT5–RPT1 put the alarm in the repeat mode
of operation. Table 3., page 17 shows the possible
configurations. Codes not listed in the table default
to the once per second mode to quickly alert the
user of an incorrect alarm setting.
When the clock information matches the alarm
clock settings based on the match criteria defined
by RPT5–RPT1, the AF (Alarm Flag) is set. If AFE
(Alarm Flag Enable) is also set, the alarm condi-
tion activates the IRQ/FT/OUT pin as shown in
Figure 17., page 17. To disable alarm, write '0' to
the Alarm Date Register and to RPT5–RPT1.
Note: If the address pointer is allowed to incre-
ment to the Flag Register address, an alarm con-
dition will not cause the Interrupt/Flag to occur until
the address pointer is moved to a different ad-
dress. It should also be noted that if the last ad-
dress written is the “Alarm Seconds,” the address
pointer will increment to the Flag address, causing
this situation to occur.
The IRQ/FT/OUT output is cleared by a READ to
the Flags Register. A subsequent READ of the
Flags Register is necessary to see that the value
of the Alarm Flag has been reset to '0.'
The IRQ/FT/OUT pin can also be activated in the
battery back-up mode. The IRQ/FT/OUT will go
low if an alarm occurs and both ABE (Alarm in Bat-
tery Back-up Mode Enable) and AFE are set. The
ABE and AFE Bits are reset during power-up,
therefore an alarm generated during power-up will
only set AF. The user can read the Flag Register
at system boot-up to determine if an alarm was
generated while the M41ST85Y/W was in the de-
select mode during power-up. Figure 18., page 18
illustrates the back-up mode alarm timing.
Figure 17. Alarm Interrupt Reset Waveform
Table 3. Alarm Repeat Modes
RPT5
RPT4
RPT3
RPT2
RPT1
Alarm Setting
1
1111
Once per Second
1
1110
Once per Minute
1
1100
Once per Hour
1
1000
Once per Day
1
0000
Once per Month
0
0000
Once per Year
AI03664
IRQ/FT/OUT
ACTIVE FLAG
0Fh
0Eh
10h
HIGH-Z
相關PDF資料
PDF描述
MC68HSC05P1ADW 8-BIT, MROM, 4 MHz, MICROCONTROLLER, PDSO28
MC68HC705PL4BCSD 8-BIT, OTPROM, 2.56 MHz, MICROCONTROLLER, PDSO28
MC68HRC705SJ7CP 8-BIT, OTPROM, 2.1 MHz, MICROCONTROLLER, PDIP28
MB90553APFV 16-BIT, MROM, 16 MHz, MICROCONTROLLER, PQFP100
M8813F2Y-90K6T 128K X 8 FLASH, 27 I/O, PIA-GENERAL PURPOSE, PQCC52
相關代理商/技術參數
參數描述
M41ST85YMX 制造商:STMICROELECTRONICS 制造商全稱:STMicroelectronics 功能描述:5.0 OR 3.0V, 512 bit 64 x 8 SERIAL RTC and NVRAM SUPERVISOR
M41ST85YMX6 功能描述:實時時鐘 Serial 512 (64x8) RoHS:否 制造商:Microchip Technology 功能:Clock, Calendar. Alarm RTC 總線接口:I2C 日期格式:DW:DM:M:Y 時間格式:HH:MM:SS RTC 存儲容量:64 B 電源電壓-最大:5.5 V 電源電壓-最小:1.8 V 最大工作溫度:+ 85 C 最小工作溫度: 安裝風格:Through Hole 封裝 / 箱體:PDIP-8 封裝:Tube
M41ST85YMX6TR 制造商:STMicroelectronics 功能描述:REAL TIME CLOCK SERL 64BYTE 28PIN SOX - Tape and Reel
M41ST85YSH 制造商:STMICROELECTRONICS 制造商全稱:STMicroelectronics 功能描述:5.0 OR 3.0V, 512 bit 64 x 8 SERIAL RTC and NVRAM SUPERVISOR
M41ST87W 制造商:STMICROELECTRONICS 制造商全稱:STMicroelectronics 功能描述:5.0, 3.3, or 3.0V, 1280 bit (160 x8) Secure Serial RTC and NVRAM Supervisor with Tamper Detection
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*