參數資料
型號： M38C29FFHP
元件分類： 微控制器/微處理器
英文描述： 8-BIT, FLASH, 4 MHz, MICROCONTROLLER, PQFP64
封裝： 10 X 10 MM, PLASTIC, LQFP-64
文件頁數： 21/101頁
文件大?。?/td> 1529K
代理商： M38C29FFHP
26
38C2 Group
SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER
MITSUBISHI MICROCOMPUTERS
PRELIMINAR
Y
Notice:
This
is not
a final
specification.
Some
parametric
limits
are
subject
to change.
Fig. 21 Waveform of PWM01
16-bit Timer
q Frequency Divider For Timer
Each timer X and timer Y have the frequency dividers for the count
source. The count source of the frequency divider is switched to XIN
or XCIN by the CPU mode register. The division ratio of each timer
can be controlled by the 3-bit register. The division ratio can be se-
lected from as follows;
1/1, 1/2, 1/16, 1/32, 1/64, 1/128, 1/256, 1/1024 of f(XIN) or f(XCIN).
q Timer X
The timer X count source can be selected by setting the timer X mode
register. When f(XCIN) is selected as the count source, counting can
be performed regardless of XCIN oscillation. However, when XCIN is
stopped, the external pulse input from XCIN pin is counted.
The timer X operates as down-count. When the timer contents reach
“000016”, an underflow occurs at the next count pulse and the timer
latch contents are reloaded. After that, the timer continues count-
down. When the timer underflows, the interrupt request bit correspond-
ing to the timer X is set to “1”.
Six operating modes can be selected for timer X by the timer X mode
register and timer X control register.
(1) Timer Mode
The count source can be selected by setting the timer X mode regis-
ter. In this mode, timer X operates as the 18-bit counter by setting the
timer X register (extension).
(2) Pulse Output Mode
Pulses of which polarity is inverted each time the timer underflows
are output from the TXOUT pin. Except for that, this mode operates
just as in the timer mode.
When using this mode, set the port sharing the TXOUT pin to output
mode.
(3) IGBT Output Mode
After dummy output from the TXOUT pin, count starts with the INT0
pin input as a trigger. In the case that the timer X output edge switch
bit is “0”, when the trigger is detected or the timer X underflows, “H” is
output from the TXOUT pin. When the count value corresponds with
the compare register value, the TXOUT output becomes “L”.
After noise is cleared by noise filters, judging continuous 4-time same
levels with sampling clocks to be signals, the INT0 signal can use 4
types of delay time by a delay circuit.
When using this mode, set the port sharing the INT0 pin to input
mode and set the port sharing the TXOUT pin to output mode.
When the timer X output control bit 1 or 2 of the timer X control reg-
ister is set to “1”, the timer X count stop bit is fixed to “1” forcibly by
the interrupt signal of INT1 or INT2. And then, by stopping the timer X
counting, the TXOUT output can be fixed to the signal output at that
time.
Do not write “1” to the timer X register (extension) when using the
IGBT output mode.
(4) PWM Mode
IGBT dummy output, an external trigger with the INT0 pin and output
control with pins INT1 and INT2 are not used. Except for those, this
mode operates just as in the IGBT output mode.
The period of PWM waveform is specified by the timer X set value. In
the case that the timer X output edge switch bit is “0”, the “H” interval
is specified by the compare register set value.
When using this mode, set the port sharing the TXOUT pin to output
mode.
Do not write “1” to the timer X register (extension) when using the
PWM mode.
Output waveform of Timer 3 PWM0 or Timer 4 PWM1
256
ts
256
ts
256
ts
256
ts
n ts
PWM01 register = “002”
n: Setting value of Timer 3 or Timer 4
ts: One period of Timer 3 count source or Timer 4 count source
PWM01 register (address 002416) : 2-bit value corresponding to PWM0 or PWM1
(n+1) ts
PWM01 register = “012”
PWM01 register = “102”
PWM01 register = “112”
Short interval
4 256
ts
Long interval
相關PDF資料
PDF描述
M38C34M6AXXXFP 8-BIT, MROM, 8 MHz, MICROCONTROLLER, PQFP80
M38C37ECMFS 8-BIT, UVPROM, 8 MHz, MICROCONTROLLER, CQCC80
M38C37ECAFP 8-BIT, OTPROM, 8 MHz, MICROCONTROLLER, PQFP80
M38C37ECMFP 8-BIT, OTPROM, 4 MHz, MICROCONTROLLER, PQFP80
M38C37ECMFS 8-BIT, UVPROM, 4 MHz, MICROCONTROLLER, CQCC80
相關代理商/技術參數
參數描述
M38C29MC-XXXFP 制造商:MITSUBISHI 制造商全稱:Mitsubishi Electric Semiconductor 功能描述:SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER
M38C29MC-XXXHP 制造商:MITSUBISHI 制造商全稱:Mitsubishi Electric Semiconductor 功能描述:SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER
M38C29RLFS 功能描述:EMULATOR MCU FOR A-VERSION 38C2 RoHS:否 類別:編程器，開發系統 >> 內電路編程器、仿真器以及調試器 系列:- 產品變化通告:Development Systems Discontinuation 19/Jul/2010 標準包裝:1 系列:* 類型:* 適用于相關產品:* 所含物品:*
M38C29T-64FPD 功能描述:DEV 100-PIN RFS/MCU TO 64-PIN 0. RoHS:否 類別:編程器，開發系統 >> 配件 系列:- 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program RoHS指令信息:IButton RoHS Compliance Plan 標準包裝:1 系列:- 附件類型:USB 至 1-Wire? RJ11 適配器 適用于相關產品:1-Wire? 設備 產品目錄頁面:1429 (CN2011-ZH PDF)
M38C29T-64LCA 制造商:RENESAS 制造商全稱:Renesas Technology Corp 功能描述:Converter from 100-pin RFS Type Emulator MCU to 64-pin 0.8mm-pitch QFP (for 38C1, 38C2, 38K0 and 38K2 Group of 38000 Series)
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*