- 您現在的位置：買賣IC網 > PDF目錄359726 > M38859M3-XXXHP (Renesas Technology Corp.) SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER PDF資料下載
參數資料
| 型號： | M38859M3-XXXHP |
| 廠商： | Renesas Technology Corp. |
| 英文描述： | SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER |
| 中文描述： | 單芯片8位CMOS微機 |
| 文件頁數： | 77/103頁 |
| 文件大小： | 1580K |
| 代理商： | M38859M3-XXXHP |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁當前第77頁第78頁第79頁第80頁第81頁第82頁第83頁第84頁第85頁第86頁第87頁第88頁第89頁第90頁第91頁第92頁第93頁第94頁第95頁第96頁第97頁第98頁第99頁第100頁第101頁第102頁第103頁
3885 Group
SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER
MITSUBISHI MICROCOMPUTERS
76
Software Commands
Table 21 lists the software commands. By entering a software com-
mand from the data I/O pins (D
0
–
D
7
) in Write mode, specify the con-
tent of the operation, such as erase or program operation, to be per-
formed.
The following explains the content of each software command.
Read Array Command (FF
16
)
The read array mode is entered by writing the command code
“
FF
16
”
in the first bus cycle. When an address to be read is input in one of
the bus cycles that follow, the content of the specified address is
output from the data I/O pins (D
0
–
D
7
).
The read array mode is retained intact until another command is writ-
ten.
The read array mode is also selected automatically when the device
is powered on and after it exits deep power down mode.
Command
Read array
Read status register
Clear status register
Program
Block erase
Mode
Write
Write
Write
Write
Write
Address
X
(Note 4)
X
X
X
X
Data
(D
0
to D
7
)
FF
16
70
16
50
16
40
16
20
16
Mode
Read
Write
Write
Address
X
WA
(Note 2)
BA
(Note 3)
Data
(D
0
to D
7
)
SRD
(Note 1)
WD
(Note 2)
D0
16
First bus cycle
Second bus cycle
Notes 1:
SRD = Status Register Data
2:
WA = Write Address, WD = Write Data
3:
BA = Block Address (Enter the maximum address of each block)
4:
X denotes a given address in the user ROM area or boot ROM area.
Read Status Register Command (70
16
)
When the command code
“
70
16
”
is written in the first bus cycle, the
content of the status register is output from the data I/O pins (D
0
–
D
7
)
by a read in the second bus cycle. Since the content of the status
register is updated at the falling edge of OE or CE, the OE or CE
signal must be asserted each time the status is read. The status
register is explained in the next section.
Clear Status Register Command (50
16
)
This command is used to clear the bits SR4,SR5 of the status regis-
ter after they have been set. These bits indicate that operation has
ended in an error. To use this command, write the command code
“
50
16
”
in the first bus cycle.
Table 21 Software command list (parallel I/O mode)
Cycle number
1
2
1
2
2
相關PDF資料 |
PDF描述 |
|---|---|
| M38859M4-XXXHP | SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER |
| M38859M5-XXXHP | SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER |
| M38859M6-XXXHP | SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER |
| M38859M7-XXXHP | SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER |
| M38859M8-XXXHP | SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER |
相關代理商/技術參數 |
參數描述 |
|---|---|
| M38859M4-XXXHP | 制造商:RENESAS 制造商全稱:Renesas Technology Corp 功能描述:SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER |
| M38859M5-XXXHP | 制造商:RENESAS 制造商全稱:Renesas Technology Corp 功能描述:SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER |
| M38859M6-XXXHP | 制造商:RENESAS 制造商全稱:Renesas Technology Corp 功能描述:SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER |
| M38859M7-XXXHP | 制造商:RENESAS 制造商全稱:Renesas Technology Corp 功能描述:SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER |
| M38859M8-XXXHP | 制造商:RENESAS 制造商全稱:Renesas Technology Corp 功能描述:SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER |
發布緊急采購，3分鐘左右您將得到回復。