參數資料
型號： M38514M6-XXXSP
元件分類： 微控制器/微處理器
英文描述： 8-BIT, MROM, 4 MHz, MICROCONTROLLER, PDIP42
封裝： 0.600 INCH, PLASTIC, SDIP-42
文件頁數： 28/91頁
文件大?。?/td> 1295K
代理商： M38514M6-XXXSP
34
SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER
MITSUBISHI MICROCOMPUTERS
3851 Group
(Built-in 24 KB or more ROM)
Fig. 33 Interrupt request signal generating timing
Fig. 32 Structure of I2C status register
Bit 6: Communication mode specification bit (transfer direc-
tion specification bit: TRX)
This bit decides a direction of transfer for data communication.
When this bit is “0,” the reception mode is selected and the data of
a transmitting device is received. When the bit is “1,” the transmis-
sion mode is selected and address data and control data are
output onto the SDA in synchronization with the clock generated
on the SCL.
This bit is set/reset by software and hardware. About set/reset by
hardware is described below. This bit is set to “1” by hardware
when all the following conditions are satisfied:
When ALS is “0”
In the slave reception mode or the slave transmission mode
When the R/W bit reception is “1”
This bit is set to “0” in one of the following conditions:
When arbitration lost is detected.
When a STOP condition is detected.
When writing “1” to this bit by software is invalid by the START
condition duplication preventing function (Note).
With MST = “0” and when a START condition is detected.
With MST = “0” and when ACK non-return is detected.
At reset
Bit 7: Communication mode specification bit (master/slave
specification bit: MST)
This bit is used for master/slave specification for data communica-
tion. When this bit is “0,” the slave is specified, so that a START
condition and a STOP condition generated by the master are re-
ceived, and data communication is performed in synchronization
with the clock generated by the master. When this bit is “1,” the
master is specified and a START condition and a STOP condition
are generated. Additionally, the clocks required for data communi-
cation are generated on the SCL.
This bit is set to “0” in one of the following conditions.
Immediately after completion of 1-byte data transfer when arbi-
tration lost is detected
When a STOP condition is detected.
Writing “1” to this bit by software is invalid by the START condi-
tion duplication preventing function (Note).
At reset
Note: START condition duplication preventing function
The MST, TRX, and BB bits is set to “1” at the same time after con-
firming that the BB flag is “0” in the procedure of a START condition
occurrence. However, when a START condition by another master
device occurs and the BB flag is set to “1” immediately after the con-
tents of the BB flag is confirmed, the START condition duplication
preventing function makes the writing to the MST and TRX bits in-
valid. The duplication preventing function becomes valid from the
rising of the BB flag to reception completion of slave address.
SCL
PIN
IICIRQ
b7
MST
b0
I2C status register
(S1 : address 002D16)
Last receive bit (Note)
0 : Last bit = “0”
1 : Last bit = “1”
General call detecting flag
(Note)
0 :No general call detected
1 :General call detected
Slave address comparison flag
(Note)
0 : Address disagreement
1 : Address agreement
Arbitration lost detecting flag
(Note)
0 :Not detected
1 :Detected
SCL pin low hold bit
0 : SCL pin low hold
1 : SCL pin low release
Bus busy flag
0 : Bus free
1 : Bus busy
Communication mode
specification bits
00 :Slave receive mode
01 :Slave transmit mode
10 :Master receive mode
11 :Master transmit mode
TRXBBPINALAASAD0LRB
Note: These bits and flags can be read out, but cannot
be written.
Write “0” to these bits at writing.
相關PDF資料
PDF描述
M38514E6SS 8-BIT, OTPROM, 4 MHz, MICROCONTROLLER, CDIP42
M38514E6-XXXFP 8-BIT, OTPROM, 4 MHz, MICROCONTROLLER, PDSO42
M38517M8-XXXFP 8-BIT, MROM, 4 MHz, MICROCONTROLLER, PDSO42
M38517M8-XXXSP 8-BIT, MROM, 4 MHz, MICROCONTROLLER, PDIP42
M38513E4FP 8-BIT, OTPROM, 4 MHz, MICROCONTROLLER, PDSO42
相關代理商/技術參數
參數描述
M38517T-ADS 功能描述:DEV TMP TRGT BRD FOR M38517RSS & RoHS:否 類別:編程器，開發系統 >> 配件 系列:- 標準包裝:1 系列:- 附件類型:適配器板 適用于相關產品:RCB230，RCB231，RCB212 配用:26790D-ND - RCB BREAKOUT BOARD RS232 CABLE
M38517T-PAC 功能描述:DEV SIMPLE TOOL EMULATOR FOR M38 RoHS:否 類別:編程器，開發系統 >> 內電路編程器、仿真器以及調試器 系列:- 產品變化通告:Development Systems Discontinuation 19/Jul/2010 標準包裝:1 系列:* 類型:* 適用于相關產品:* 所含物品:*
M3852 BK001 制造商:Alpha Wire 功能描述:CBL 8COND 14AWG BLK 1000'
M3852 BK002 制造商:Alpha Wire 功能描述:CBL 8COND 14AWG BLK 500'
M3852 BK005 制造商:Alpha Wire 功能描述:CBL 8COND 14AWG BLK 100'
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*