- 您現在的位置：買賣IC網 > PDF目錄45046 > M38513E4FP 8-BIT, OTPROM, 4 MHz, MICROCONTROLLER, PDSO42 PDF資料下載
參數資料
| 型號： | M38513E4FP |
| 元件分類： | 微控制器/微處理器 |
| 英文描述： | 8-BIT, OTPROM, 4 MHz, MICROCONTROLLER, PDSO42 |
| 封裝： | 0.450 INCH, PLASTIC, SSOP-42 |
| 文件頁數： | 27/91頁 |
| 文件大?。?/td> | 1295K |
| 代理商： | M38513E4FP |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁當前第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁第77頁第78頁第79頁第80頁第81頁第82頁第83頁第84頁第85頁第86頁第87頁第88頁第89頁第90頁第91頁
33
SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER
MITSUBISHI MICROCOMPUTERS
3851 Group
(Built-in 24 KB or more ROM)
Bit 4: SCL pin low hold bit (PIN)
This bit generates an interrupt request signal. Each time 1-byte
data is transmitted, the PIN bit changes from “1” to “0.” At the
same time, an interrupt request signal occurs to the CPU. The PIN
bit is set to “0” in synchronization with a falling of the last clock (in-
cluding the ACK clock) of an internal clock and an interrupt
request signal occurs in synchronization with a falling of the PIN
bit. When the PIN bit is “0,” the SCL is kept in the “0” state and
clock generation is disabled. Figure 33 shows an interrupt request
signal generating timing chart.
The PIN bit is set to “1” in one of the following conditions:
Executing a write instruction to the I2C data shift register (ad-
dress 002B16). (This is the only condition which the prohibition of
the internal clock is released and data can be communicated ex-
cept for the start condition detection.)
When the ES0 bit is “0”
At reset
When writing “1” to the PIN bit by software
The conditions in which the PIN bit is set to “0” are shown below:
Immediately after completion of 1-byte data transmission (includ-
ing when arbitration lost is detected)
Immediately after completion of 1-byte data reception
In the slave reception mode, with ALS = “0” and immediately af-
ter completion of slave address agreement or general call
address reception
In the slave reception mode, with ALS = “1” and immediately af-
ter completion of address data reception
Bit 5: Bus busy flag (BB)
This bit indicates the status of use of the bus system. When this
bit is set to “0,” this bus system is not busy and a START condition
can be generated. The BB flag is set/reset by the SCL, SDA pins
input signal regardless of master/slave. This flag is set to “1” by
detecting the start condition, and is set to “0” by detecting the stop
condition. The condition of these detecting is set by the start/stop
condition setting bits (SSC4–SSC0) of the I2C start/stop condition
control register (address 003016). When the ES0 bit of the I2C
control register (address 002E16) is “0” or reset, the BB flag is set
to “0.”
For the writing function to the BB flag, refer to the sections
“START Condition Generating Method” and “STOP Condition Gen-
erating Method” described later.
[I2C Status Register (S1)] 002D16
The I2C status register (address 002D16) controls the I2C-BUS in-
terface status. The low-order 4 bits are read-only bits and the
high-order 4 bits can be read out and written to.
Set “00002” to the low-order 4 bits, because these bits become the
reserved bits at writing.
Bit 0: Last receive bit (LRB)
This bit stores the last bit value of received data and can also be
used for ACK receive confirmation. If ACK is returned when an
ACK clock occurs, the LRB bit is set to “0.” If ACK is not returned,
this bit is set to “1.” Except in the ACK mode, the last bit value of
received data is input. The state of this bit is changed from “1” to
“0” by executing a write instruction to the I2C data shift register
(address 002B16).
Bit 1: General call detecting flag (AD0)
When the ALS bit is “0”, this bit is set to “1” when a general call
whose address data is all “0” is received in the slave mode. By a
general call of the master device, every slave device receives con-
trol data after the general call. The AD0 bit is set to “0” by
detecting the STOP condition or START condition, or reset.
General call: The master transmits the general call address “0016” to all
slaves.
Bit 2: Slave address comparison flag (AAS)
This flag indicates a comparison result of address data when the
ALS bit is “0”.
In the slave receive mode, when the 7-bit addressing format is
selected, this bit is set to “1” in one of the following conditions:
The address data immediately after occurrence of a START
condition agrees with the slave address stored in the high-or-
der 7 bits of the I2C address register (address 002C16).
A general call is received.
In the slave receive mode, when the 10-bit addressing format is
selected, this bit is set to “1” with the following condition:
When the address data is compared with the I2C address reg-
ister (8 bits consisting of slave address and RWB bit), the first
bytes agree.
This bit is set to “0” by executing a write instruction to the I2C
data shift register (address 002B16) when ES0 is set to “1” or
reset.
Bit 3: Arbitration lost detecting flag (AL)
In the master transmission mode, when the SDA is made “L” by
any other device, arbitration is judged to have been lost, so that
this bit is set to “1.” At the same time, the TRX bit is set to “0,” so
that immediately after transmission of the byte whose arbitration
was lost is completed, the MST bit is set to “0.” The arbitration lost
can be detected only in the master transmission mode. When ar-
bitration is lost during slave address transmission, the TRX bit is
set to “0” and the reception mode is set. Consequently, it becomes
possible to detect the agreement of its own slave address and ad-
dress data transmitted by another master device.
Arbitration lost :The status in which communication as a master is dis-
abled.
相關PDF資料 |
PDF描述 |
|---|---|
| M38517M8-XXXFP | 8-BIT, MROM, 4 MHz, MICROCONTROLLER, PDSO42 |
| M38517M8-XXXSP | 8-BIT, MROM, 4 MHz, MICROCONTROLLER, PDIP42 |
| M38514E6SP | 8-BIT, OTPROM, 4 MHz, MICROCONTROLLER, PDIP42 |
| M38588GCFP | 8-BIT, MROM, 6.25 MHz, MICROCONTROLLER, PDSO42 |
| M38749EFT | 8-BIT, OTPROM, 6.4 MHz, MICROCONTROLLER, PQFP80 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| M38513E4FP#U0 | 功能描述:IC 740 MCU ROM 16K 42SSOP RoHS:否 類別:集成電路 (IC) >> 嵌入式 - 微控制器， 系列:740/38000 產品培訓模塊:CAN Basics Part-1 CAN Basics Part-2 Electromagnetic Noise Reduction Techniques Part 1 M16C Product Overview Part 1 M16C Product Overview Part 2 標準包裝:1 系列:M16C™ M32C/80/87 核心處理器:M32C/80 芯體尺寸:16/32-位 速度:32MHz 連通性:EBI/EMI，I²C，IEBus，IrDA，SIO，UART/USART 外圍設備:DMA，POR，PWM，WDT 輸入/輸出數:121 程序存儲器容量:384KB（384K x 8） 程序存儲器類型:閃存 EEPROM 大小:- RAM 容量:24K x 8 電壓 - 電源 (Vcc/Vdd):3 V ~ 5.5 V 數據轉換器:A/D 34x10b，D/A 2x8b 振蕩器型:內部 工作溫度:-20°C ~ 85°C 封裝/外殼:144-LQFP 包裝:托盤 產品目錄頁面:749 (CN2011-ZH PDF) 配用:R0K330879S001BE-ND - KIT DEV RSK M32C/87 |
| M38514E6FP | 制造商:Renesas Electronics Corporation 功能描述:SLIM740 OTP 24K/640B RAM, W/A-D, I2C, L - Rail/Tube |
| M38514E6SP | 制造商:Renesas Electronics Corporation 功能描述:SLIM740 OTP 24K/640B RAM, W/A-D, I2C, L - Rail/Tube |
| M38517T-ADS | 功能描述:DEV TMP TRGT BRD FOR M38517RSS & RoHS:否 類別:編程器，開發系統 >> 配件 系列:- 標準包裝:1 系列:- 附件類型:適配器板 適用于相關產品:RCB230，RCB231，RCB212 配用:26790D-ND - RCB BREAKOUT BOARD RS232 CABLE |
| M38517T-PAC | 功能描述:DEV SIMPLE TOOL EMULATOR FOR M38 RoHS:否 類別:編程器，開發系統 >> 內電路編程器、仿真器以及調試器 系列:- 產品變化通告:Development Systems Discontinuation 19/Jul/2010 標準包裝:1 系列:* 類型:* 適用于相關產品:* 所含物品:* |
發布緊急采購，3分鐘左右您將得到回復。