- 您現在的位置：買賣IC網 > PDF目錄45046 > M38504M6A-XXXSP 8-BIT, MROM, 6.25 MHz, MICROCONTROLLER, PDIP42 PDF資料下載
參數資料
| 型號： | M38504M6A-XXXSP |
| 元件分類： | 微控制器/微處理器 |
| 英文描述： | 8-BIT, MROM, 6.25 MHz, MICROCONTROLLER, PDIP42 |
| 封裝： | 13 X 36.72 MM, 1.78 MM PITCH, PLASTIC, SDIP-42 |
| 文件頁數： | 43/90頁 |
| 文件大?。?/td> | 899K |
| 代理商： | M38504M6A-XXXSP |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁當前第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁第77頁第78頁第79頁第80頁第81頁第82頁第83頁第84頁第85頁第86頁第87頁第88頁第89頁第90頁
Rev.2.10
2005.11.14
page 46 of 86
REJ03B0093-0210
3850 Group (Spec.A)
Software Commands (CPU Rewrite Mode)
Table 9 lists the software commands.
After setting the CPU Rewrite Mode Select Bit of the flash memory
control register to “1”, execute a software command to specify an
erase or program operation.
Each software command is explained below.
qRead Array Command (FF16)
The read array mode is entered by writing the command code
“FF16” in the first bus cycle. When an address to be read is input in
one of the bus cycles that follow, the contents of the specified ad-
dress are read out at the data bus (D0 to D7).
The read array mode is retained intact until another command is
written.
qRead Status Register Command (7016)
The read status register mode is entered by writing the command
code “7016” in the first bus cycle. The contents of the status regis-
ter are read out at the data bus (D0 to D7) by a read in the second
bus cycle.
The status register is explained in the next section.
qClear Status Register Command (5016)
This command is used to clear the bits SR1, SR4, and SR5 of the
status register after they have been set. These bits indicate that
operation has ended in an error. To use this command, write the
command code “5016” in the first bus cycle.
qProgram Command (4016)
Program operation starts when the command code “4016” is writ-
ten in the first bus cycle. Then, if the address and data to program
are written in the 2nd bus cycle, program operation (data program-
ming and verification) will start.
Whether the write operation is completed can be confirmed by
_____
reading the status register or the RY/BY Status Flag of the flash
memory control register. When the program starts, the read status
Table 9 List of software commands (CPU rewrite mode)
register mode is entered automatically and the contents of the sta-
tus register is read at the data bus (D0 to D7). The status register
bit 7 (SR7) is set to “0” at the same time the write operation starts
and is returned to “1” upon completion of the write operation. In
this case, the read status register mode remains active until the
next command is written.
____
The RY/BY Status Flag is “0” (busy) during write operation and “1”
(ready) when the write operation is completed as is the status reg-
ister bit 7.
At program end, program results can be checked by reading bit 4
(SR4) of the status register.
Fig. 50 Program flowchart
Start
Write 4016
Status register
read
Program completed
(Read array command
“FF16” write)
NO
YES
Write address
Write data
SR4 = 0 ?
Program
error
NO
YES
SR7 = 1 ?
or
RY/BY = 1 ?
Write
Command
Program
Clear status register
Read array
Read status register
X
First bus cycle
Second bus cycle
FF16
7016
5016
4016
Write
XSRD
Read
Write
Erase all blocks2016
WriteX
2016
Write
(Note 2)
WA (Note 3)
WD (Note 3)
Block erase2016
WriteD016
WriteBA (Note 4)
Mode
Address
Mode
Address
Data
(D0 to D7)
(Note 1)
Notes 1: X denotes a given address in the User ROM area .
2: SRD = Status Register Data
3: WA = Write Address, WD = Write Data
4: BA = Block Address to be erased (Input the maximum address of each block.)
Cycle number
1
2
1
2
X
Data
相關PDF資料 |
PDF描述 |
|---|---|
| M38513M4-XXXFP | 8-BIT, MROM, 4 MHz, MICROCONTROLLER, PDSO42 |
| M38514E6-XXXFP | 8-BIT, MROM, 4 MHz, MICROCONTROLLER, PDSO42 |
| M38514E6FP | 8-BIT, OTPROM, 4 MHz, MICROCONTROLLER, PDSO42 |
| M38514M6-XXXFP | 8-BIT, MROM, 4 MHz, MICROCONTROLLER, PDSO42 |
| M38514E6-XXXSP | 8-BIT, MROM, 4 MHz, MICROCONTROLLER, PDIP42 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| M38507ARLSS | 功能描述:M-SUPPORT TOOL RoHS:否 類別:編程器，開發系統 >> 配件 系列:- 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program RoHS指令信息:IButton RoHS Compliance Plan 標準包裝:1 系列:- 附件類型:USB 至 1-Wire? RJ11 適配器 適用于相關產品:1-Wire? 設備 產品目錄頁面:1429 (CN2011-ZH PDF) |
| M38507F8AFP#U1 | 功能描述:IC 740/3850 MCU FLASH 42SSOP RoHS:是 類別:集成電路 (IC) >> 嵌入式 - 微控制器， 系列:740/38000 產品培訓模塊:CAN Basics Part-1 CAN Basics Part-2 Electromagnetic Noise Reduction Techniques Part 1 M16C Product Overview Part 1 M16C Product Overview Part 2 標準包裝:1 系列:M16C™ M32C/80/87 核心處理器:M32C/80 芯體尺寸:16/32-位 速度:32MHz 連通性:EBI/EMI，I²C，IEBus，IrDA，SIO，UART/USART 外圍設備:DMA，POR，PWM，WDT 輸入/輸出數:121 程序存儲器容量:384KB（384K x 8） 程序存儲器類型:閃存 EEPROM 大小:- RAM 容量:24K x 8 電壓 - 電源 (Vcc/Vdd):3 V ~ 5.5 V 數據轉換器:A/D 34x10b，D/A 2x8b 振蕩器型:內部 工作溫度:-20°C ~ 85°C 封裝/外殼:144-LQFP 包裝:托盤 產品目錄頁面:749 (CN2011-ZH PDF) 配用:R0K330879S001BE-ND - KIT DEV RSK M32C/87 |
| M38507F8AFP#W1 | 制造商:Renesas Electronics Corporation 功能描述:MCU 3/5V 32K PB-FREE 42-SSOP T&R - Tape and Reel |
| M38507F8FP | 制造商:Renesas Electronics Corporation 功能描述:MCU 8-Bit 740 CISC 32KB Flash 5V 42-Pin SSOP 制造商:Renesas Electronics Corporation 功能描述:MCU 8BIT 740 CISC 32KB FLASH 5V 42SSOP - Trays |
| M38507F8FP#U1 | 制造商:Renesas Electronics Corporation 功能描述:MCU 8BIT 740 CISC 32KB FLASH 5V 42SSOP - Trays |
發布緊急采購，3分鐘左右您將得到回復。