參數資料
型號： M3823AGFHP
元件分類： 微控制器/微處理器
英文描述： 8-BIT, MROM, 10 MHz, MICROCONTROLLER, PQFP80
封裝： 12 X 12 MM, 0.50 MM PITCH, PLASTIC, LQFP-80
文件頁數： 51/64頁
文件大?。?/td> 922K
代理商： M3823AGFHP
Rev.2.02
Jun 19, 2007
page 53 of 73
REJ03B0146-0202
3823 Group
Fig. 56 Clock generating circuit block diagram
Oscillation Control
(1) Stop Mode
If the STP instruction is executed, the internal clock φ stops at an
“H” level, and XIN and XCIN oscillators stop. Timer 1 is set to
“FF16” and timer 2 is set to “0116”.
Either XIN or XCIN divided by 16 is input to timer 1 as count
source, and the output of timer 1 is connected to timer 2. The bits
of the timer 123 mode register except bit 4 are cleared to “0”. Set
the timer 1 and timer 2 interrupt enable bits to disabled (“0”) be-
fore executing the STP instruction. Oscillator restarts at reset or
when an external interrupt is received, but the internal clock φ is
not supplied to the CPU until timer 2 underflows. This allows timer
for the clock circuit oscillation to stabilize.
Execution of the STP instruction sets the LCD enable bit (bit 3 of
the LCD mode register) to “0” and the LCD panel turns off.To
make the LCD panel turn on after returning from the stop mode,
set the LCD enable bit to “1”.
(2) Wait Mode
If the WIT instruction is executed, only the system clock φ stops at
an "H" state. The states of main clock, on-chip oscillator and sub
clock are the same as the state before executing the WIT instruc-
tion, and oscillation does not stop. Since supply of system clock φ
is started immediately after the interrupt is received, the instruc-
tion can be executed immediately.
Timing φ
(Internal system clock)
Main clock stop bit
Timer 2
Timer 1
1/2
1/4
XIN
XOUT
WIT
instruction
STP instruction
S
R
Q
STP instruction
S
R
Q
S
R
Q
Interrupt request
Interrupt disable flag 1
Reset
1/2
“1”
“0”
Timer 1
count source
selection bit
“0”
“1”
Timer 2
count source
selection bit
Low-speed mode
Frequency/2/4/8
mode
(Note 1)
Frequency/8 mode
Frequency/2/4
mode or low-
speed mode
Internal system clock selection bit
Main clock division
ratio selection bit
“1”
“0”
“1”
Notes 1: When using the low-speed mode, set the port XC switch bit to “1” .
2: Although a feed-back resistor exists on-chip, an external feed-back resistor may be needed depending
on conditions.
Frequency/4
mode
control bit
1/2
XCOUT
XCIN
Port XC
switch bit
“0”
“1”
On-chip
oscillator
On-chip oscillator
control bit
f(SUB)
(Note 2)
相關PDF資料
PDF描述
M38235G6-XXXFP 8-BIT, MROM, 10 MHz, MICROCONTROLLER, PQFP80
M38238G8-XXXHP 8-BIT, MROM, 10 MHz, MICROCONTROLLER, PQFP80
M38254M6-XXXGP 8-BIT, MROM, 4 MHz, MICROCONTROLLER, PQFP100
M38254M4-XXXGP 8-BIT, MROM, 4 MHz, MICROCONTROLLER, PQFP100
M38257E8-XXXFP 8-BIT, OTPROM, 4 MHz, MICROCONTROLLER, PQFP100
相關代理商/技術參數
參數描述
M3823AGFHP#U0 功能描述:MCU 2/5V 60K 80-LQFP QZ-ROM RoHS:是 類別:集成電路 (IC) >> 嵌入式 - 微控制器， 系列:740/38000 標準包裝:250 系列:80C 核心處理器:8051 芯體尺寸:8-位 速度:16MHz 連通性:EBI/EMI，I²C，UART/USART 外圍設備:POR，PWM，WDT 輸入/輸出數:40 程序存儲器容量:- 程序存儲器類型:ROMless EEPROM 大小:- RAM 容量:256 x 8 電壓 - 電源 (Vcc/Vdd):4.5 V ~ 5.5 V 數據轉換器:A/D 8x10b 振蕩器型:內部 工作溫度:-40°C ~ 85°C 封裝/外殼:68-LCC（J 形引線） 包裝:帶卷 (TR)
M3823AT-RLFS 功能描述:DEV EMULATOR PERSONALITY KIT M38 RoHS:否 類別:編程器，開發系統 >> 配件 系列:- 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program RoHS指令信息:IButton RoHS Compliance Plan 標準包裝:1 系列:- 附件類型:USB 至 1-Wire? RJ11 適配器 適用于相關產品:1-Wire? 設備 產品目錄頁面:1429 (CN2011-ZH PDF)
M3823-BLACK-1000 制造商:Alpha Wire 功能描述:
M3824 功能描述:電纜固定件和配件 LTSCG 1000 BLACK RoHS:否 制造商:Heyco 類型:Cable Grips, Liquid Tight 材料:Nylon 顏色:Black 安裝方法:Cable 最大光束直徑:11.4 mm 抗拉強度:
M38257E8FP 制造商:Renesas Electronics Corporation 功能描述:8-BIT, OTPROM, 4 MHz, MICROCONTROLLER, PQFP100
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*