- 您現在的位置：買賣IC網 > PDF目錄370849 > M37754 (Mitsubishi Electric Corporation) SINGLE-CHIP 16BIT CMOS MICROCOMPUTER PDF資料下載
參數資料
| 型號： | M37754 |
| 廠商： | Mitsubishi Electric Corporation |
| 英文描述： | SINGLE-CHIP 16BIT CMOS MICROCOMPUTER |
| 中文描述： | 單芯片16位微機的CMOS |
| 文件頁數： | 29/114頁 |
| 文件大?。?/td> | 1116K |
| 代理商： | M37754 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁當前第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁第77頁第78頁第79頁第80頁第81頁第82頁第83頁第84頁第85頁第86頁第87頁第88頁第89頁第90頁第91頁第92頁第93頁第94頁第95頁第96頁第97頁第98頁第99頁第100頁第101頁第102頁第103頁第104頁第105頁第106頁第107頁第108頁第109頁第110頁第111頁第112頁第113頁第114頁
29
PRELIMINARY
Notice: This is not a final specification.
Some parametric limits are subject to change.
MITSUBISHI MICROCOMPUTERS
M37754M8C-XXXGP, M37754M8C-XXXHP
M37754S4CGP, M37754S4CHP
SINGLE-CHIP 16-BIT CMOS MICROCOMPUTER
(3) One-shot pulse mode [10]
Figure 28 shows the bit configuration of the timer Ai mode register
during one-shot pulse mode. In one-shot pulse mode, bit 0 and bit 5
must be “0” and bit 1 and bit 2 must be “1”.
The trigger is enabled when the count start bit is “1”. The trigger can
be generated by software or it can be input from the TAi
IN
pin. Soft-
ware trigger is selected when bit 4 is “0” and the input signal from the
TAi
IN
pin is used as the trigger when it is “1“.
Bit 3 is used to determine whether to trigger at the fall of the trigger
signal or at the rise. The trigger is at the fall of the trigger signal when
bit 3 is “0” and at the rise of the trigger signal when it is “1”.
Software trigger is generated by setting the bit in the one-shot start
bit corresponding to each timer.
Figure 29 shows the bit configuration of the one-shot start register.
As shown in Figure 30, when a trigger signal is received, the counter
counts the clock selected by bits 6 and 7.
If the contents of the counter is not 0000
16
, the TAi
OUT
pin goes “H”
when a trigger signal is received. The count direction is decrement.
When the counter reaches 0001
16
, The TAi
OUT
pin goes “L” and
count is stopped. The contents of the reload register is transferred to
the counter. At the same time, an interrupt request signal is gener-
ated and the interrupt request bit in the timer Ai interrupt control reg-
ister is set. This is repeated each time a trigger signal is received.
The output pulse width is
If the count start flag is “0”, TAi
OUT
goes “L”. Therefore, the value
corresponding to the desired pulse width must be written to timer Ai
before setting the timer Ai count start bit.
As shown in Figure 31, a trigger signal can be received before the
operation for the previous trigger signal is completed. In this case,
the contents of the reload register is transferred to the counter by the
trigger and then that value is decremented.
Except when retriggering while operating, the contents of the reload
register is not transferred to the counter by triggering.
When retriggering, there must be at least one timer count source
cycle before a new trigger can be issued.
Data write is performed in the same way as for timer mode.
When data is written in timer Ai halted, it is also written to the reload
register and the counter.
When data is written to timer Ai which is busy, the data is written to
the reload register, but not to the counter. The counter is reloaded
with new data from the reload register at the next reload time.
Undefined data is read when timer Ai is read.
1
pulse frequency of the selected clock
×
(counter’s value at the time of trigger).
Fig. 28 Timer Ai mode register bit configuration during one-shot
pulse mode
Fig. 29 One-shot start register bit configuration
7 6 5 4 3 2 1 0
0
0
1
1
1 0 : Always “10” in one-shot pulse mode
1 : Always “1” in one-shot pulse mode
0
×
: Software trigger
1 0 : Trigger at the falling edge of TAi
IN
input
1 1 : Trigger at the rising edge of TAi
IN
input
0 : Always “0” in one-shot pulse mode
Clock source select
0 0 : Select Pf
2
0 1 : Select Pf
16
1 0 : Select Pf
64
1 1 : Select Pf
512
Timer A0 mode register
Timer A1 mode register
Timer A2 mode register
Timer A3 mode register
Timer A4 mode register
Addresses
56
16
57
16
58
16
59
16
5A
16
7 6 5 4 3 2 1 0
Timer A0 one-shot start bit
Timer A1 one-shot start bit
Timer A2 one-shot start bit
Timer A3 one-shot start bit
Timer A4 one-shot start bit
One-shot start register
Address
42
16
相關PDF資料 |
PDF描述 |
|---|---|
| M37754M8C | Single Chip 16 Bits CMOS Microcomputer(16位單片機) |
| M37902F8CHP | DIODE SCHOTTKY DUAL COMMON-ANODE 25V 200mW 0.32V-vf 200mA-IFM 1mA-IF 2uA-IR SOT-23 3K/REEL |
| M37902FGCGP | SINGLE-CHIP 16-BIT CMOS MICROCOMPUTER |
| M37902FCCHP | SINGLE-CHIP 16-BIT CMOS MICROCOMPUTER |
| M37902FGCHP | DIODE SCHOTTKY DUAL COMMON-ANODE 25V 150mW 0.32V-vf 200mA-IFM 1mA-IF 2uA-IR SOT-523 3K/REEL |
相關代理商/技術參數 |
參數描述 |
|---|---|
| M37754FFCGP | 制造商:MITSUBISHI 制造商全稱:Mitsubishi Electric Semiconductor 功能描述:SINGLE-CHIP 16-BIT CMOS MICROCOMPUTER FLASH MEMORY VERSION |
| M37754FFCHP | 制造商:MITSUBISHI 制造商全稱:Mitsubishi Electric Semiconductor 功能描述:SINGLE-CHIP 16-BIT CMOS MICROCOMPUTER FLASH MEMORY VERSION |
| M37754M6C-XXXGP | 制造商:RENESAS 制造商全稱:Renesas Technology Corp 功能描述:SINGLE-CHIP 16-BIT CMOS MICROCOMPUTER |
| M37754M6C-XXXHP | 制造商:RENESAS 制造商全稱:Renesas Technology Corp 功能描述:SINGLE-CHIP 16-BIT CMOS MICROCOMPUTER |
| M37754M8C-XXXGP | 制造商:MITSUBISHI 制造商全稱:Mitsubishi Electric Semiconductor 功能描述:SINGLE-CHIP 16BIT CMOS MICROCOMPUTER |
發布緊急采購，3分鐘左右您將得到回復。