參數資料
型號： M37702M2-127FP
廠商： Mitsubishi Electric Corporation
英文描述： SINGLE-CHIP 16-BIT CMOS MICROCOMPUTER
中文描述： 單片16位CMOS微機
文件頁數： 35/59頁
文件大?。?/td> 811K
代理商： M37702M2-127FP
35
MITSUBISHI MICROCOMPUTERS
M37702M2AXXXFP, M37702M2BXXXFP
M37702S1AFP, M37702S1BFP
SINGLE-CHIP 16-BIT CMOS MICROCOMPUTER
(1) One-shot mode [00]
The A-D conversion pins are selected with the bit 0 to 2 of A-D
control register. A-D conversion can be started by a software trig-
ger or by an external trigger.
A software trigger is selected when the bit 5 of A-D control register
is “0” and an external trigger is selected when it is “1”.
When a software trigger is selected, A-D conversion is started
when bit 6 (A-D conversion start flag) is set. A-D conversion ends
after 57
φ
AD
cycles and an interrupt request bit is set in the A-D
conversion interrupt control register. At the same time, A-D control
register bit 6 (A-D conversion start flag) is cleared and A-D con-
version stops. The result of A-D conversion is stored in the A-D
register corresponding to the selected pin.
If an external trigger is selected, A-D conversion starts when the
A-D conversion start flag is “1” and the AD
TRG
input changes from
“H” to “L”. In this case, the pins that can be used for A-D conver-
sion are AN
0
to AN
6
because the AD
TRG
pin is shared with the
analog voltage input pin AN
7
. The operation is the same as with
software trigger except that the A-D conversion start flag is not
cleared after A-D conversion and a retrigger can be available dur-
ing A-D conversion.
(2) Repeat mode [01]
The operation of this mode is the same as the operation of one-
shot mode except that when A-D conversion of the selected pin is
complete and the result is stored in the A-D register, conversion
does not stop, but is repeated. Also, no interrupt request is issued
in this mode. Furthermore, if software trigger is selected, the A-D
conversion start flag is not cleared. The contents of the A-D regis-
ter can be read at any time.
(3) Single sweep mode [10]
In the sweep mode, the number of analog input pins to be swept
can be selected. Analog input pins are selected by bits 1 and 0 of
the A-D sweep pin selection register (1F
16
address) shown in Fig-
ure 45. Two pins, four pins, six pins, or eight pins can be selected
as analog input pins, depending on the contents of these bits.
A-D conversion is performed only for selected input pins. After
A-D conversion is performed for input of AN
0
pin, the conversion
result is stored in A-D register 0, and in the same way, A-D conver-
sion is performed for selected pins one after another. After A-D
conversion is performed for all selected pins, the sweep is
stopped.
A-D conversion can be started with a software trigger or with an
external trigger input. A software trigger is selected when bit 5 is
“0” and an external trigger is selected when it is “1”.
When a software trigger is selected, A-D conversion is started
when A-D control register bit 6 (A-D conversion start flag) is set.
When A-D conversion of all selected pins end, an interrupt request
bit is set in the A-D conversion interrupt control register. At the
same time, A-D control register bit 6 (A-D conversion start flag) is
cleared and A-D conversion stops.
When an external trigger is selected, A-D conversion starts when
the A-D conversion start flag is “1” and the AD
TRG
input changes
from “H” to “L”. In this case, the A-D conversion result of the trig-
ger input itself is stored in the A-D register 7 because the AD
TRG
pin is shared with AN
7
pin.
The operation is the same as done by software trigger except that
the A-D conversion start flag is not cleared after A-D conversion
and a retrigger can be available during A-D conversion.
(4) Repeat sweep mode [11]
The difference with the single sweep mode is that A-D conversion
does not stop after converting from the AN
0
pin to the selected
pins, but repeats again from the AN
0
pin. The repeat is performed
among the selected pins. Also, no interrupt request is generated.
Furthermore, if software trigger is selected, the A-D conversion
start flag is not cleared. The A-D register can be read at any time.
Fig. 45 A-D sweep pin selection register configuration
0 0 : AN
0
, AN
1
(2 pins)
0 1 : AN
0
to AN
3
(4 pins)
1 0 : AN
0
to AN
5
(6 pins)
1 1 : AN
0
to AN
7
(8 pins)
7
1F
16
Address
A-D sweep pin
selection register
6
5
4
3
2
1
0
相關PDF資料
PDF描述
M37702S1AFP Single Chip 16 Bits CMOS Microcomputer(16位單片機)
M37702S1BFP Single Chip 16 Bits CMOS Microcomputer(16位單片機)
M37702M2A Single Chip 16 Bits CMOS Microcomputer(16位單片機)
M37702M2B Single Chip 16 Bits CMOS Microcomputer(16位單片機)
M37702M2AXXXFP SINGLE-CHIP 16-BIT CMOS MICROCOMPUTER
相關代理商/技術參數
參數描述
M37702M2A 制造商:MITSUBISHI 制造商全稱:Mitsubishi Electric Semiconductor 功能描述:SINGLE-CHIP 16-BIT CMOS MICROCOMPUTER
M37702M2A-278FP 制造商:MITSUBISHI 制造商全稱:Mitsubishi Electric Semiconductor 功能描述:SINGLE-CHIP 16-BIT CMOS MICROCOMPUTER
M37702M2AXXXFP 制造商:RENESAS 制造商全稱:Renesas Technology Corp 功能描述:SINGLE-CHIP 16-BIT CMOS MICROCOMPUTER
M37702M2A-XXXFP 制造商:MITSUBISHI 制造商全稱:Mitsubishi Electric Semiconductor 功能描述:SINGLE-CHIP 16-BIT CMOS MICROCOMPUTER
M37702M2BXXXFP 制造商:MITSUBISHI 制造商全稱:Mitsubishi Electric Semiconductor 功能描述:SINGLE-CHIP 16-BIT CMOS MICROCOMPUTER
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*