參數資料
型號： M37548G2-XXXFP
元件分類： 微控制器/微處理器
英文描述： 8-BIT, MROM, 8 MHz, MICROCONTROLLER, PDSO20
封裝： 4.40 X 6.50 MM, 0.65 MM PITCH, PLASTIC, LSSOP-20
文件頁數： 22/86頁
文件大?。?/td> 1437K
代理商： M37548G2-XXXFP
Rev.2.02
Mar 31, 2009
Page 27 of 81
REJ03B0210-0202
7548 Group
Timers
The 7548 Group has two 8-bit timers (timer 1 and timer 2) and
one 16-bit timer (timer A).
Timer 1 and timer 2 share the same 8-bit prescaler (prescaler 12).
Each timer and prescaler has a separate timer latch and prescaler
latch.
The division ratio of every timer and prescaler is 1/(n+1), where
n is the value of the timer latch or prescaler latch.
The timers decrement at each count clock input. When the count
value reaches “0”, an underflow occurs at the next count pulse.
The value of the corresponding timer latch is reloaded into the
timer at underflow and counting is continued. When a timer
underflow occurs, the interrupt request bit corresponding to each
timer is set to “1”.
Prescaler 12 (PRE12)
Prescaler 12 is an 8-bit prescaler that counts the signal selected
by the prescaler 12 count source selection bit. The count source
can be selected from
φSOURCE/16 and XCIN input clock.
Writing to prescaler 12 writes the value to both the prescaler
latch and prescaler.
Reading from prescaler 12 reads the prescaler 12 count value.
The initial value is set to “FF16” after reset.
The division ratio of prescaler 12 is 1/(n+1), where n is the
setting value.
Prescaler 12 cannot stop counting by software.
Timer 1 (T1)
Timer 1 is an 8-bit timer that counts the prescaler 12 output.
When Timer 1 underflows, the timer 1 interrupt request bit is set
to “1”.
Writing to timer 1 writes the value to both the timer 1 latch and
timer 1.
Reading from timer 1 reads the timer 1 count value. The initial
value is set to “0116” after reset.
The division ratio of timer 1 is 1/(m+1), where m is the setting
value. This gives that the division ratio of prescaler 12 and timer
1 is 1/((n+1)
× (m+1)), where n is the prescaler 12 setting value
and m is the timer 1 setting value.
Timer 1 cannot stop counting by software.
Timer 2 (T2)
Timer 2 is an 8-bit timer that counts the signal selected by the
timer 2 count source selection bit.
The count source can be selected from among
φSOURCE/16,
/256, prescaler 12 output, and timer A output signal.
Timer 2 counts the selected count source and sets the timer 2
interrupt request bit to “1” at underflow.
When writing to timer 2, the value of the timer 2 write control bit
can be used to select a write to both the timer 2 latch and timer 2
or a write to only the timer 2 latch.
Reading from timer 2 reads the timer 2 count value.
Timer 2 starts counting from “FF16” after reset.
The division ratio of timer 2 is 1/(n+1), where n is the timer 2
setting value. Timer 2 stops when the timer 2 count stop bit is set
to “1”.
When the P13/T2OUT output valid bit is set to “1”, the polarity of
the waveform output from the P13/T2OUT pin can be inverted at
each timer 2 underflow. The output start level of the T2OUT pin
can be selected using the T2OUT polarity switch bit. When this
bit is set to 0, the output starts at “H” level. When this bit is set to
“1”, the output starts at “L” level.
Notes
(1) Reading from and Writing to Timer 1 and 2 and Prescaler 12
If the timer/prescaler count source clock and
φSOURCE are
different clocks, the timers and prescaler cannot be read or
written. Select the same clock to enable read and write
operations.
Note that timer 2 can be read and written even using a
different clock while its counting is stopped.
1Prescaler 12 and timer 1 cannot be read/written in the
following conditions:
Prescaler 12 count source: XCIN input clock
φSOURCE: Clock other than XCIN input clock
2Timer 2 cannot be read/written during counting in the
following conditions:
Timer 2 count source: Prescaler 12
Prescaler 12 count source: XCIN input clock
φSOURCE: Clock other than XCIN input clock
or
Timer 2 count source: Timer A underflow
Timer A count source: XCIN input clock
φSOURCE: Clock other than XCIN input clock
or
Timer 2 count source: Timer A underflow
Timer A count source: low-speed on-chip oscillator
output
φSOURCE: Clock other than low-speed on-chip oscillator
(2) Count Source of Prescaler 12
The XCIN input clock can be selected as the prescaler count
source only if the 32 kHz quartz crystal oscillator is selected
by the oscillation method selection bit in FSROM1.
相關PDF資料
PDF描述
M37548G2FP 8-BIT, MROM, 8 MHz, MICROCONTROLLER, PDSO20
M37548G1FP 8-BIT, MROM, 8 MHz, MICROCONTROLLER, PDSO20
M37549G1-XXXFP 8-BIT, MROM, 8 MHz, MICROCONTROLLER, PDSO24
M37549G3-XXXFP 8-BIT, MROM, 8 MHz, MICROCONTROLLER, PDSO24
M37560M8-XXXFP 8-BIT, MROM, 8 MHz, MICROCONTROLLER, PQFP100
相關代理商/技術參數
參數描述
M37548G3FP 制造商:RENESAS 制造商全稱:Renesas Technology Corp 功能描述:SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER
M37548G3FP#U0 功能描述:MCU 6K ROM 256K 20-SSOP RoHS:是 類別:集成電路 (IC) >> 嵌入式 - 微控制器， 系列:740/38000 標準包裝:250 系列:LPC11Uxx 核心處理器:ARM? Cortex?-M0 芯體尺寸:32-位 速度:50MHz 連通性:I²C，Microwire，SPI，SSI，SSP，UART/USART，USB 外圍設備:欠壓檢測/復位，POR，WDT 輸入/輸出數:40 程序存儲器容量:96KB（96K x 8） 程序存儲器類型:閃存 EEPROM 大小:4K x 8 RAM 容量:10K x 8 電壓 - 電源 (Vcc/Vdd):1.8 V ~ 3.6 V 數據轉換器:A/D 8x10b 振蕩器型:內部 工作溫度:-40°C ~ 85°C 封裝/外殼:48-LQFP 包裝:托盤 其它名稱:568-9587
M37548G3-XXXFP 制造商:RENESAS 制造商全稱:Renesas Technology Corp 功能描述:SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER
M37549G1FP 制造商:RENESAS 制造商全稱:Renesas Technology Corp 功能描述:SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER
M37549G1-XXXFP 制造商:RENESAS 制造商全稱:Renesas Technology Corp 功能描述:SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*