- 您現在的位置：買賣IC網 > PDF目錄45035 > M37542M2V-XXXGP 8-BIT, MROM, 8 MHz, MICROCONTROLLER, PQFP32 PDF資料下載
參數資料
| 型號： | M37542M2V-XXXGP |
| 元件分類： | 微控制器/微處理器 |
| 英文描述： | 8-BIT, MROM, 8 MHz, MICROCONTROLLER, PQFP32 |
| 封裝： | 7 X 7 MM, 0.80 MM PITCH, PLASTIC, LQFP-32 |
| 文件頁數： | 31/139頁 |
| 文件大?。?/td> | 1448K |
| 代理商： | M37542M2V-XXXGP |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁當前第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁第77頁第78頁第79頁第80頁第81頁第82頁第83頁第84頁第85頁第86頁第87頁第88頁第89頁第90頁第91頁第92頁第93頁第94頁第95頁第96頁第97頁第98頁第99頁第100頁第101頁第102頁第103頁第104頁第105頁第106頁第107頁第108頁第109頁第110頁第111頁第112頁第113頁第114頁第115頁第116頁第117頁第118頁第119頁第120頁第121頁第122頁第123頁第124頁第125頁第126頁第127頁第128頁第129頁第130頁第131頁第132頁第133頁第134頁第135頁第136頁第137頁第138頁第139頁
7542 Group
Rev.3.02
Oct 31, 2006
Page 126 of 134
REJ03B0006-0302
5. Read-modify-write instruction
Do not execute a read-modify-write instruction to the read invalid
address (SFR).
The read-modify-write instruction operates in the following se-
quence: read one-byte of data from memory, modify the data,
write the data back to original memory. The following instructions
are classified as the read-modify-write instructions in the 740
Family.
(1) Bit management instructions: CLB, SEB
(2) Shift and rotate instructions: ASL, LSR, ROL, ROR, RRF
(3) Add and subtract instructions: DEC, INC
(4) Logical operation instructions (1’s complement): COM
Add and subtract/logical operation instructions (ADC, SBC, AND,
EOR, and ORA) when T flag = “1” operate in the way as the read-
modify-write instruction. Do not execute the read invalid SFR.
<Reason>
When the read-modify-write instruction is executed to read invalid
SFR, the instruction may cause the following consequence: the in-
struction reads unspecified data from the area due to the read
invalid condition. Then the instruction modifies this unspecified
data and writes the data to the area. The result will be random
data written to the area or some unexpected event.
NOTES ON PERIPHERAL FUNCTIONS
Notes on I/O Ports
1. Setting of 32-pin version and PWQN0036KA-A package version
(1) Set direction registers of ports P26, P27, P35 and P36 to output.
(2) Select P33 for the INT1 function by the INT1 input port selec-
tion bit (bit 2 of interrupt edge selection register (address
3A16)).
(3) Be sure to set P36/INT1 input level selection bit (bit 1 of port
P1P3 control register (address 1716)) to “0”.
2. Port P0P3 drive capacity control register
The number of LED drive port (drive capacity is HIGH) is 8.
3. Pull-up control register
When using each port which built in pull-up resistor as an output
port, the pull-up control bit of corresponding port becomes invalid,
and pull-up resistor is not connected.
<Reason>
Pull-up control is effective only when each direction register is set
to the input mode.
4. Notes in stand-by state
In stand-by state*1 for low-power dissipation, do not make input
levels of an input port and an I/O port “undefined”.
Pull-up (connect the port to Vcc) or pull-down (connect the port to
Vss) these ports through a resistor.
When determining a resistance value, note the following points:
External circuit
Variation of output levels during the ordinary operation
When using a built-in pull-up resistor, note on varied current val-
ues:
When setting as an input port : Fix its input level
When setting as an output port : Prevent current from flowing out
to external.
<Reason>
The output transistor becomes the OFF state, which causes the
ports to be the high-impedance state. Note that the level becomes
“undefined” depending on external circuits.
Accordingly, the potential which is input to the input buffer in a mi-
crocomputer is unstable in the state that input levels of an input
port and an I/O port are “undefined”. This may cause power
source current.
*1 stand-by state : the stop mode by executing the STP instruction
the wait mode by executing the WIT instruction
5. Modifying output data with bit managing instruction
When the port latch of an I/O port is modified with the bit manag-
ing instruction*2, the value of the unspecified bit may be changed.
<Reason>
The bit managing instructions are read-modify-write form instruc-
tions for reading and writing data by a byte unit. Accordingly, when
these instructions are executed on a bit of the port latch of an I/O
port, the following is executed to all bits of the port latch.
As for a bit which is set for an input port :
The pin state is read in the CPU, and is written to this bit after bit
managing.
As for a bit which is set for an output port :
The bit value of the port latch is read in the CPU, and is written to
this bit after bit managing.
Note the following :
Even when a port which is set as an output port is changed for
an input port, its port latch holds the output data.
As for a bit of the port latch which is set for an input port, its
value may be changed even when not specified with a bit man-
aging instruction in case where the pin state differs from its port
latch contents.
*2 bit managing instructions : SEB, and CLB instructions
相關PDF資料 |
PDF描述 |
|---|---|
| M37542M2-XXXSP | 8-BIT, MROM, 8 MHz, MICROCONTROLLER, PDIP32 |
| M37542F8SP | 8-BIT, FLASH, 8 MHz, MICROCONTROLLER, PDIP32 |
| M37542F8FP | 8-BIT, FLASH, 8 MHz, MICROCONTROLLER, PDSO36 |
| M37542F8GP | 8-BIT, FLASH, 8 MHz, MICROCONTROLLER, PQFP32 |
| M37542F4GP | 8-BIT, FLASH, 8 MHz, MICROCONTROLLER, PQFP32 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| M37542M2-XXXFP | 制造商:RENESAS 制造商全稱:Renesas Technology Corp 功能描述:SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER |
| M37542M2-XXXGP | 制造商:RENESAS 制造商全稱:Renesas Technology Corp 功能描述:SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER |
| M37542M2-XXXHP | 制造商:RENESAS 制造商全稱:Renesas Technology Corp 功能描述:SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER |
| M37542M2-XXXSP | 制造商:RENESAS 制造商全稱:Renesas Technology Corp 功能描述:SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER |
| M37542M4-XXXFP | 制造商:RENESAS 制造商全稱:Renesas Technology Corp 功能描述:SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER |
發布緊急采購，3分鐘左右您將得到回復。