- 您現在的位置：買賣IC網 > PDF目錄45035 > M37542F8GP 8-BIT, FLASH, 4 MHz, MICROCONTROLLER, PQFP32 PDF資料下載
參數資料
| 型號： | M37542F8GP |
| 元件分類： | 微控制器/微處理器 |
| 英文描述： | 8-BIT, FLASH, 4 MHz, MICROCONTROLLER, PQFP32 |
| 封裝： | 7 X 7 MM, 0.80 MM PITCH, PLASTIC, LQFP-32 |
| 文件頁數： | 61/68頁 |
| 文件大?。?/td> | 1191K |
| 代理商： | M37542F8GP |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁當前第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁
SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER
7542 Group
MITSUBISHI MICROCOMPUTERS
64
PRELIMINAR
Y
Notice:
This
is not
a final
specification.
Some
parametric
limits
are
subject
to change.
s Notes on Clock Generating Circuit
For use with the oscillation stabilization set bit after release of the
STP instruction set to “1”, set values in timer 1 and prescaler 1 af-
ter fully appreciating the oscillation stabilization time of the
oscillator to be used.
Switch of ceramic and RC oscillations
After releasing reset the operation starts by starting a built-in ring
oscillator. Then, a ceramic oscillation or an RC oscillation is se-
lected by setting bit 5 of the CPU mode register.
Double-speed mode
When a ceramic oscillation is selected, a double-speed mode can
be used. Do not use it when an RC oscillation is selected.
CPU mode register
Bits 5, 1 and 0 of CPU mode register are used to select oscillation
mode and to control operation modes of the microcomputer. In or-
der to prevent the dead-lock by error-writing (ex. program
run-away), these bits can be rewritten only once after releasing re-
set. After rewriting it is disable to write any data to the bit. (The
emulator MCU “M37542RSS” is excluded.)
Also, when the read-modify-write instructions (SEB, CLB) are ex-
ecuted to bits 2 to 4, 6 and 7, bits 5, 1 and 0 are locked.
Clock division ratio, XIN oscillation control, ring oscillator control
The state transition shown in Fig. 79 can be performed by setting
the clock division ratio selection bits (bits 7 and 6), XIN oscillation
control bit (bit 4), ring oscillator oscillation control bit (bit 3) of CPU
mode register. Be careful of notes on use in Fig. 79.
s Notes on Ring Oscillation Division Ratio
When system is released from reset, ROSC/8 (ring middle-speed
mode) is selected for CPU clock.
When state transition from the ceramic or RC oscillation to ring oscil-
lator, ROSC/8 (ring middle-speed mode) is selected for CPU clock.
When the MCU operates by ring-oscillator for the main clock
without external oscillation circuit, connect XIN pin to VCC
through a resistor and leave XOUT pin open.
Set “10010x002” (x = 0 or 1) to CPUM.
s Notes on Oscillation Stop Detection Circuit
When the oscillation stop reset bit is set to “0”, internal reset
does not occur. If the ceramic or RC oscillation is selected for
the CPU clock, MCU will be locked when the ceramic or RC os-
cillation is stopped. So when the ceramic or RC oscillation is
selected for the main clock, set the oscillation stop reset bit to
“1”. (State 2’a of Fig. 81)
Ceramic or RC oscillation stop detection function active bit is not
cleared by the oscillation stop internal reset. Accordingly, the
oscillation stop detection circuit is in active when system is re-
leased from internal reset cause of oscillation stop detection.
Oscillation stop detection status bit is initialized by the following
operation.
(1) External reset
(2) Write “0” data to the ceramic or RC oscillation stop detection
function active bit.
The oscillation stop detection circuit is not included in the emu-
lator MCU “M37542RSS”.
DATA REQUIRED FOR MASK ORDERS
The following are necessary when ordering a mask ROM produc-
tion:
1.Mask ROM Order Confirmation Form *
2.Mark Specification Form *
3.Data to be written to ROM, in EPROM form (three identical cop-
ies) or one floppy disk.
* For the mask ROM confirmation, ROM programming order con-
firmation and the mark specifications, refer to the “Mitsubishi
MCU Technical Information” Homepage
(http://www.infomicom.maec.co.jp/indexe.htm).
相關PDF資料 |
PDF描述 |
|---|---|
| M37542M4-XXXSP | 8-BIT, MROM, 4 MHz, MICROCONTROLLER, PDIP32 |
| M37542F8SP | 8-BIT, FLASH, 4 MHz, MICROCONTROLLER, PDIP32 |
| M37542F8VGP | 8-BIT, FLASH, 4 MHz, MICROCONTROLLER, PQFP32 |
| M37542F8FP | 8-BIT, FLASH, 4 MHz, MICROCONTROLLER, PDSO36 |
| M37542F8VFP | 8-BIT, FLASH, 8 MHz, MICROCONTROLLER, PDSO36 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| M37542F8GP#U0 | 功能描述:MCU 3/5V 32K+4K PB-FREE 32-LQFP RoHS:是 類別:集成電路 (IC) >> 嵌入式 - 微控制器， 系列:740/38000 標準包裝:250 系列:80C 核心處理器:8051 芯體尺寸:8-位 速度:16MHz 連通性:EBI/EMI，I²C，UART/USART 外圍設備:POR，PWM，WDT 輸入/輸出數:40 程序存儲器容量:- 程序存儲器類型:ROMless EEPROM 大小:- RAM 容量:256 x 8 電壓 - 電源 (Vcc/Vdd):4.5 V ~ 5.5 V 數據轉換器:A/D 8x10b 振蕩器型:內部 工作溫度:-40°C ~ 85°C 封裝/外殼:68-LCC（J 形引線） 包裝:帶卷 (TR) |
| M37542F8GPSP | 制造商:RENESAS 制造商全稱:Renesas Technology Corp 功能描述:SINGLE-CHIP MICROCOMPUTER |
| M37542F8HP | 制造商:RENESAS 制造商全稱:Renesas Technology Corp 功能描述:SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER |
| M37542F8SP | 制造商:RENESAS 制造商全稱:Renesas Technology Corp 功能描述:SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER |
| M37542F8SP#U0 | 制造商:Renesas Electronics Corporation 功能描述:MCU 4.0/5.5V 32K PB-FREE 32-SDIP - Trays |
發布緊急采購，3分鐘左右您將得到回復。