參數資料
型號： M37532
廠商： Mitsubishi Electric Corporation
英文描述： Single Chip 8 Bits CMOS Microcomputer(8位單片機)
中文描述： 單芯片的CMOS 8位單片機（8位單片機）
文件頁數： 18/50頁
文件大?。?/td> 524K
代理商： M37532
SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER
7532 Group
MITSUBISHI MICROCOMPUTERS
18
Timers
The 7532 Group has 3 timers: timer X, timer 1 and timer 2.
The division ratio of every timer and prescaler is 1/(n+1) provided
that the value of the timer latch or prescaler is n.
All the timers are down count timers. When a timer reaches “0”, an
underflow occurs at the next count pulse, and the corresponding timer
latch is reloaded into the timer. When a timer underflows, the inter-
rupt request bit corresponding to each timer is set to “1”.
G
Timer 1, Timer 2
Prescaler 12 always counts f(X
IN
)/16. Timer 1 and timer 2 always
count the prescaler output and periodically sets the interrupt request
bit.
G
Timer X
Timer X can be selected in one of 4 operating modes by setting the
timer X mode register.
Timer Mode
The timer counts the signal selected by the timer X count source
selection bit.
Pulse Output Mode
The timer counts the signal selected by the timer X count source
selection bit, and outputs a signal whose polarity is inverted each
time the timer value reaches “0”, from the CNTR
0
pin.
When the CNTR
0
active edge switch bit is “0”, the output of the
CNTR
0
pin is started with an “H” output.
At “1”, this output is started with an “L” output. When using a timer in
this mode, set the port P1
4
direction register to output mode.
Event Counter Mode
The operation in the event counter mode is the same as that in the
timer mode except that the timer counts the input signal from the
CNTR
0
pin.
When the CNTR
0
active edge switch bit is “0”, the timer counts
the rising edge of the CNTR
0
pin. When this bit is “1”, the timer
counts the falling edge of the CNTR
0
pin.
Pulse Width Measurement Mode
When the CNTR
0
active edge switch bit is “0”, the timer counts the
signal selected by the timer X count source selection bit while the
CNTR
0
pin is “H”. When this bit is “1”, the timer counts the signal
while the CNTR
0
pin is “L”.
In any mode, the timer count can be stopped by setting the timer X
count stop bit to “1”. Each time the timer overflows, the interrupt
request bit is set.
Fig. 18 Structure of timer X mode register
Fig. 19 Timer count source set register
Timer X mode register
(TM : Address 002B
16
)
Timer X operating mode bits
b1 b0
0 0 : Timer mode
0 1 : Pulse output mode
1 0 : Event counter mode
1 1 : Pulse width measurement mode
CNTR
0
active edge switch bit
0 : Interrupt at falling edge
Count at rising edge
(in event counter mode)
1 : Interrupt at rising edge
Count at falling edge
(in event counter mode)
Timer X count stop bit
0 : Count start
1 : Count stop
Not used (return “0” when read)
b7 b0
Timer count source set register
(TCSS : Address 002E
16
)
Timer X count source selection bit (Note)
0 : f(X
IN
)/16
1 : f(X
IN
)/2
b7 b0
Not used (return “0” when read)
Note :
To switch the timer X count source selection bit ,
stop the timer X count operation.
相關PDF資料
PDF描述
M37536M4 SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER
M37536RSS SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER
M37536E8SP SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER
M37536 Single Chip 8 Bits CMOS Microcomputer(8位單片機)
M37536M4-XXXSP SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER
相關代理商/技術參數
參數描述
M37532E8FP 制造商:MITSUBISHI 制造商全稱:Mitsubishi Electric Semiconductor 功能描述:SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER
M37532M4 制造商:MITSUBISHI 制造商全稱:Mitsubishi Electric Semiconductor 功能描述:SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER
M37532M4-A17GP 制造商:MITSUBISHI 制造商全稱:Mitsubishi Electric Semiconductor 功能描述:SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER
M37532M4-XXXFP 制造商:未知廠家 制造商全稱:未知廠家 功能描述:8-Bit Microcontroller
M37532M4-XXXGP 制造商:未知廠家 制造商全稱:未知廠家 功能描述:8-Bit Microcontroller
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*