- 您現在的位置：買賣IC網 > PDF目錄45034 > M37531M8-XXXFP 8-BIT, MROM, 8 MHz, MICROCONTROLLER, PDSO36 PDF資料下載
參數資料
| 型號： | M37531M8-XXXFP |
| 元件分類： | 微控制器/微處理器 |
| 英文描述： | 8-BIT, MROM, 8 MHz, MICROCONTROLLER, PDSO36 |
| 封裝： | 0.450 INCH, PLASTIC, SSOP-36 |
| 文件頁數： | 159/215頁 |
| 文件大?。?/td> | 1365K |
| 代理商： | M37531M8-XXXFP |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁第77頁第78頁第79頁第80頁第81頁第82頁第83頁第84頁第85頁第86頁第87頁第88頁第89頁第90頁第91頁第92頁第93頁第94頁第95頁第96頁第97頁第98頁第99頁第100頁第101頁第102頁第103頁第104頁第105頁第106頁第107頁第108頁第109頁第110頁第111頁第112頁第113頁第114頁第115頁第116頁第117頁第118頁第119頁第120頁第121頁第122頁第123頁第124頁第125頁第126頁第127頁第128頁第129頁第130頁第131頁第132頁第133頁第134頁第135頁第136頁第137頁第138頁第139頁第140頁第141頁第142頁第143頁第144頁第145頁第146頁第147頁第148頁第149頁第150頁第151頁第152頁第153頁第154頁第155頁第156頁第157頁第158頁當前第159頁第160頁第161頁第162頁第163頁第164頁第165頁第166頁第167頁第168頁第169頁第170頁第171頁第172頁第173頁第174頁第175頁第176頁第177頁第178頁第179頁第180頁第181頁第182頁第183頁第184頁第185頁第186頁第187頁第188頁第189頁第190頁第191頁第192頁第193頁第194頁第195頁第196頁第197頁第198頁第199頁第200頁第201頁第202頁第203頁第204頁第205頁第206頁第207頁第208頁第209頁第210頁第211頁第212頁第213頁第214頁第215頁
HARDWARE
7531 Group User’s Manual
1-34
Clock Generating Circuit
An oscillation circuit can be formed by connecting a resonator be-
tween XIN and XOUT, and an RC oscillation circuit can be formed by
connecting a resistor and a capacitor.
Use the circuit constants in accordance with the resonator
manufacturer's recommended values. No external resistor is needed
between XIN and XOUT since a feed-back resistor exists on-chip.
Set the constants of the resistor and capacitor when an RC oscillator
is used, so that a frequency variation due to LSI variation and resis-
tor and capacitor variations may not exceed the standard input fre-
quency.
qOscillation control
Stop mode
When the STP instruction is executed, the internal clock f stops at
an “H” level and the XIN oscillator stops. At this time, timer 1 is set
to “0116” and prescaler 12 is set to “FF16” when the oscillation sta-
bilization time set bit after release of the STP instruction is “0”. On
the other hand, timer 1 and prescaler 12 are not set when the
above bit is “1”. Accordingly, set the wait time fit for the oscillation
stabilization time of the oscillator to be used. f(XIN)/16 is forcibly
connected to the input of prescaler 12. When an external interrupt
is accepted, oscillation is restarted but the internal clock f remains
at “H” until timer 1 underflows. As soon as timer 1 underflows, the
internal clock f is supplied. This is because when a ceramic oscilla-
tor is used, some time is required until a start of oscillation. In case
oscillation is restarted by reset, no wait time is generated. So apply
an “L” level to the RESET pin while oscillation becomes stable.
Wait mode
If the WIT instruction is executed, the internal clock f stops at an “H”
level, but the oscillator does not stop. The internal clock restarts if
a reset occurs or when an interrupt is received. Since the oscillator
does not stop, normal operation can be started immediately after
the clock is restarted. To ensure that interrupts will be received to
release the STP or WIT state, interrupt enable bits must be set to
“1” before the STP or WIT instruction is executed.
When the STP status is released, prescaler 12 and timer 1 will start
counting clock which is XIN divided by 16, so set the timer 1 inter-
rupt enable bit to “0” before the STP instruction is executed.
Note
For use with the oscillation stabilization set bit after release of the
STP instruction set to “1”, set values in timer 1 and prescaler
12 after fully appreciating the oscillation stabilization time of the
oscillator to be used.
qSwitch of ceramic and RC oscillations
After releasing reset the operation starts by starting a built-in ring
oscillator. Then, a ceramic oscillation or an RC oscillation is selected
by setting bit 5 of the CPU mode register.
The bit 5 can be rewritten only once after releasing reset. However,
after rewriting it is disable to write any value to the bit.
qDouble-speed mode
When a ceramic oscillation is selected, a double-speed mode can be
used. Do not use it when an RC oscillation is selected.
FUNCTIONAL DESCRIPTION
相關PDF資料 |
PDF描述 |
|---|---|
| M37531M4T-XXXFP | 8-BIT, MROM, 8 MHz, MICROCONTROLLER, PDSO36 |
| M37531M4T-XXXGP | 8-BIT, MROM, 8 MHz, MICROCONTROLLER, PQFP32 |
| M37531E4V-XXXGP | 8-BIT, OTPROM, 8 MHz, MICROCONTROLLER, PQFP32 |
| M37531E8SP | 8-BIT, OTPROM, 8 MHz, MICROCONTROLLER, PDIP32 |
| M37531E8FP | 8-BIT, OTPROM, 8 MHz, MICROCONTROLLER, PDSO36 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| M37531RSS | 制造商:Mitsubishi Electric 功能描述: |
| M37531T-ADS | 制造商:RENESAS 制造商全稱:Renesas Technology Corp 功能描述:Temporary Target Board |
| M37532E8FP | 制造商:MITSUBISHI 制造商全稱:Mitsubishi Electric Semiconductor 功能描述:SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER |
| M37532M4 | 制造商:MITSUBISHI 制造商全稱:Mitsubishi Electric Semiconductor 功能描述:SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER |
| M37532M4-A17GP | 制造商:MITSUBISHI 制造商全稱:Mitsubishi Electric Semiconductor 功能描述:SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER |
發布緊急采購，3分鐘左右您將得到回復。