- 您現在的位置：買賣IC網 > PDF目錄45034 > M37531M4T-XXXFP 8-BIT, MROM, 8 MHz, MICROCONTROLLER, PDSO36 PDF資料下載
參數資料
| 型號： | M37531M4T-XXXFP |
| 元件分類： | 微控制器/微處理器 |
| 英文描述： | 8-BIT, MROM, 8 MHz, MICROCONTROLLER, PDSO36 |
| 封裝： | 0.450 INCH, PLASTIC, SSOP-36 |
| 文件頁數： | 163/215頁 |
| 文件大?。?/td> | 1365K |
| 代理商： | M37531M4T-XXXFP |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁第77頁第78頁第79頁第80頁第81頁第82頁第83頁第84頁第85頁第86頁第87頁第88頁第89頁第90頁第91頁第92頁第93頁第94頁第95頁第96頁第97頁第98頁第99頁第100頁第101頁第102頁第103頁第104頁第105頁第106頁第107頁第108頁第109頁第110頁第111頁第112頁第113頁第114頁第115頁第116頁第117頁第118頁第119頁第120頁第121頁第122頁第123頁第124頁第125頁第126頁第127頁第128頁第129頁第130頁第131頁第132頁第133頁第134頁第135頁第136頁第137頁第138頁第139頁第140頁第141頁第142頁第143頁第144頁第145頁第146頁第147頁第148頁第149頁第150頁第151頁第152頁第153頁第154頁第155頁第156頁第157頁第158頁第159頁第160頁第161頁第162頁當前第163頁第164頁第165頁第166頁第167頁第168頁第169頁第170頁第171頁第172頁第173頁第174頁第175頁第176頁第177頁第178頁第179頁第180頁第181頁第182頁第183頁第184頁第185頁第186頁第187頁第188頁第189頁第190頁第191頁第192頁第193頁第194頁第195頁第196頁第197頁第198頁第199頁第200頁第201頁第202頁第203頁第204頁第205頁第206頁第207頁第208頁第209頁第210頁第211頁第212頁第213頁第214頁第215頁
7531 Group User’s Manual
1-37
HARDWARE
NOTES ON PROGRAMMING
Processor Status Register
The contents of the processor status register (PS) after reset are
undefined except for the interrupt disable flag I which is “1”. After
reset, initialize flags which affect program execution. In particular, it
is essential to initialize the T flag and the D flag because of their
effect on calculations.
Interrupts
The contents of the interrupt request bit do not change even if the
BBC or BBS instruction is executed immediately after they are
changed by program because this instruction is executed for the pre-
vious contents. For executing the instruction for the changed con-
tents, execute one instruction before executing the BBC or BBS in-
struction.
Decimal Calculations
For calculations in decimal notation, set the decimal mode flag D to
“1”, then execute the ADC instruction or SBC instruction. In this
case, execute SEC instruction, CLC instruction or CLD instruction
after executing one instruction before the ADC instruction or SBC
instruction.
In the decimal mode, the values of the N (negative), V (overflow)
and Z (zero) flags are invalid.
Timers
When n (0 to 255) is written to a timer latch, the frequency division
ratio is 1/(n+1).
When a count source of timer X is switched, stop a count of timer X.
Ports
The values of the port direction registers cannot be read.
That is, it is impossible to use the LDA instruction, memory opera-
tion instruction when the T flag is “1”, addressing mode using di-
rection register values as qualifiers, and bit test instructions such
as BBC and BBS.
It is also impossible to use bit operation instructions such as CLB
and SEB and read/modify/write instructions of direction registers
for calculations such as ROR.
For setting direction registers, use the LDM instruction, STA in-
struction, etc.
Set "1" to each bit 6 of the port P3 direction register and the port P3
register.
A-D Converter
The comparator uses internal capacitors whose charge will be lost if
the clock frequency is too low.
Make sure that f(XIN) is 500kHz or more during A-D conversion.
Do not execute the STP instruction during A-D conversion.
Instruction Execution Timing
The instruction execution time can be obtained by multiplying the
frequency of the internal clock
φ by the number of cycles mentioned
in the machine-language instruction table.
The frequency of the internal clock
φ is the same as that of the XIN in
double-speed mode, twice the XIN cycle in high-speed mode and 8
times the XIN cycle in middle-speed mode.
CPU Mode Register
The oscillation mode selection bit can be rewritten only once after
releasing reset. However, after rewriting it is disable to write any value
to the bit.
When a ceramic oscillation is selected, a double-speed mode of the
clock division ratio selection bits can be used. Do not use it when an
RC oscillation is selected.
NOTES ON USE
Handling of Power Source Pin
In order to avoid a latch-up occurrence, connect a capacitor suitable
for high frequencies as bypass capacitor between power source pin
(Vcc pin) and GND pin (Vss pin). Besides, connect the capacitor to
as close as possible. For bypass capacitor which should not be lo-
cated too far from the pins to be connected, a ceramic capacitor of
0.01
F to 0.1 F is recommended.
One Time PROM Version
The CNVss pin is connected to the internal memory circuit block by a
low-ohmic resistance, since it has the multiplexed function to be a
programmable power source pin (VPP pin) as well.
To improve the noise reduction, connect a track between CNVss pin
and Vss pin with 1 to 10 k
resistance.
The mask ROM version track of CNVss pin has no operational inter-
ference even if it is connected via a resistor.
NOTES ON PROGRAMMING
相關PDF資料 |
PDF描述 |
|---|---|
| M37531M4T-XXXGP | 8-BIT, MROM, 8 MHz, MICROCONTROLLER, PQFP32 |
| M37531E4V-XXXGP | 8-BIT, OTPROM, 8 MHz, MICROCONTROLLER, PQFP32 |
| M37531E8SP | 8-BIT, OTPROM, 8 MHz, MICROCONTROLLER, PDIP32 |
| M37531E8FP | 8-BIT, OTPROM, 8 MHz, MICROCONTROLLER, PDSO36 |
| M37531E4T-XXXGP | 8-BIT, OTPROM, 8 MHz, MICROCONTROLLER, PQFP32 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| M37531RSS | 制造商:Mitsubishi Electric 功能描述: |
| M37531T-ADS | 制造商:RENESAS 制造商全稱:Renesas Technology Corp 功能描述:Temporary Target Board |
| M37532E8FP | 制造商:MITSUBISHI 制造商全稱:Mitsubishi Electric Semiconductor 功能描述:SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER |
| M37532M4 | 制造商:MITSUBISHI 制造商全稱:Mitsubishi Electric Semiconductor 功能描述:SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER |
| M37532M4-A17GP | 制造商:MITSUBISHI 制造商全稱:Mitsubishi Electric Semiconductor 功能描述:SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER |
發(fā)布緊急采購，3分鐘左右您將得到回復。