參數資料
型號： M37470M4-716SP
廠商： Mitsubishi Electric Corporation
英文描述： SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER
中文描述： 單芯片8位CMOS微機
文件頁數： 37/46頁
文件大小： 646K
代理商： M37470M4-716SP
37
7470/7471 Group
SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER
MITSUBISHI MICROCOMPUTERS
Caution : Since the screening temperature is higher than storage
temperature, never expose to 150
°
C exceeding 100
hours.
Read-out
Output disable
Programming
Programming verify
Program disable
Output
Floating
Input
Output
Floating
V
IL
V
IH
V
IH
V
IL
V
IH
V
CC
V
CC
V
PP
V
PP
V
PP
V
CC
V
CC
V
CC
V
CC
V
CC
V
IL
V
IL
V
IL
V
IH
V
IH
Pin
Mode
CE
OE
V
PP
V
CC
Data I/O
Note :
V
IL
and V
IH
indicate a “L” and “H” input voltage, respectively.
Table 3. I/O signal in each mode
PROM READING AND WRITING
Reading
To read the PROM, set the CE and OE pins to “L” level. Input the
address of the data (A
0
–A
14
) to be read and the data will be out-
put to the I/O pins (D
0
–D
7
). The data I/O pins will be floating when
either the CE or OE pin is in the “H” state.
Writing
To write to the PROM, set the OE pin to “H” level. The CPU will en-
ter the program mode when V
PP
is applied to the V
PP
pin. The
address to be written to is selected with pins A
0
–A
14
, and the
data to be written is input to pins D
0
–D
7
. Set the CE pin to “L” level
to begin writing.
Notes on Writing
M37470E4, M37471E4
When using a PROM programmer, the address range should be
between 6000
16
and 7FFF
16
. Addresses 0000
16
to 5FFF
16
can-
not be written to or read from correctly.
M37470E8, M37471E8
When using a PROM programmer, the address range should be
between 4000
16
and 7FFF
16
. When data is written between ad-
dresses 0000
16
and 7FFF
16
, fill addresses 0000
16
to 3FFF
16
with FF
16
.
Erasing
Data can only erased on the M37471E8SS ceramic package,
which includes a window. To erase data on this chip, use an ultra-
violet light source with a 2537 Angstrom wave length. The
minimum radiation power necessary for erasing is 15W·s/cm
2
.
NOTES ON HANDLING
(1) Sunlight and fluorescent light contain wave lengths capable of
erasing data. For ceramic package types, cover the transpar-
ent window with a seal (provided) when this chip is in use.
However, this seal must not contact the lead pins.
(2) Before erasing, the glass should be cleaned and stains such
as finger prints should be removed thoroughly. If these stains
are not removed, complete erasure of the data could be pre-
vented.
(3) Since a high voltage (12.5 V) is used to write data, care should
be taken when turning on the PROM programmer’s power.
(4) For the programmable microcomputer (shipped in One Time
PROM version), Mitsubishi does not perform PROM write test
and screening in the assembly process and following pro-
cesses. To improve reliability after write, performing write and
test according to the flow below before use is recommended.
Writing with PROM programmer
Verify test with PROM programmer
Function check in target device
Screening (Caution) (Leave at 150
°
C for 40 hours)
相關PDF資料
PDF描述
M37470M4-743SP SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER
M37470M4-751SP SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER
M37470M4-768SP SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER
M37470M4-779SP SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER
M37470M8-421SP SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER
相關代理商/技術參數
參數描述
M37470M4-743SP 制造商:MITSUBISHI 制造商全稱:Mitsubishi Electric Semiconductor 功能描述:SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER
M37470M4-751SP 制造商:MITSUBISHI 制造商全稱:Mitsubishi Electric Semiconductor 功能描述:SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER
M37470M4-768SP 制造商:MITSUBISHI 制造商全稱:Mitsubishi Electric Semiconductor 功能描述:SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER
M37470M4-779SP 制造商:MITSUBISHI 制造商全稱:Mitsubishi Electric Semiconductor 功能描述:SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER
M37470M4-XXXSP 制造商:MITSUBISHI 制造商全稱:Mitsubishi Electric Semiconductor 功能描述:SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*