參數資料
型號: M37281MFH-XXXSP
元件分類: 微控制器/微處理器
英文描述: 8-BIT, MROM, 8 MHz, MICROCONTROLLER, PDIP52
封裝: PLASTIC, SHRINK, DIP-52
文件頁數: 84/158頁
文件大?。?/td> 1472K
代理商: M37281MFH-XXXSP
31
SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER with CLOSED CAPTION DECODER
and ON-SCREEN DISPLAY CONTROLLER
MITSUBISHI MICROCOMPUTERS
Rev. 1.0
M37281MAH–XXXSP,M37281MFH–XXXSP
M37281MKH–XXXSP,M37281EKSP
Fig. 8.5.2 Serial I/O Timing (for LSB first)
Synchronous clock
Transfer clock
Serial I/O register
write signal
Serial I/O output
SOUT
D0
D1
D2
D3
D4
D5
D6
D7
(Note)
Serial I/O input
SIN
Note : When an internal clock is selected, the SOUT pin is at high-impedance after transfer is completed.
Interrupt request bit is set to “1”
Internal clock : The serial I/O counter is set to “7” during the write
cycle into the serial I/O register (address 021416), and the transfer
clock goes “H” forcibly. At each falling edge of the transfer clock after
the write cycle, serial data is output from the SOUT pin. Transfer di-
rection can be selected by bit 5 of the serial I/O mode register. At
each rising edge of the transfer clock, data is input from the SIN pin
and data in the serial I/O register is shifted 1 bit.
After the transfer clock has counted 8 times, the serial I/O counter
becomes “0” and the transfer clock stops at HIGH. At this time the
interrupt request bit is set to “1.”
External clock : The an external clock is selected as the clock source,
the interrupt request is set to “1” after the transfer clock has been
counted 8 counts. However, transfer operation does not stop, so the
clock should be controlled externally. Use the external clock of
500 kHz or less with a duty cycle of 50 %.
The serial I/O timing is shown in Figure 8.5.2. When using an exter-
nal clock for transfer, the external clock must be held at HIGH for
initializing the serial I/O counter. When switching between an inter-
nal clock and an external clock, do not switch during transfer. Also,
be sure to initialize the serial I/O counter after switching.
Notes 1: On programming, note that the serial I/O counter is set by writing to
the serial I/O register with the bit managing instructions, such as SEB
and CLB.
2: When an external clock is used as the synchronous clock, write trans-
mit data to the serial I/O register when the transfer clock input level is
HIGH.
相關PDF資料
PDF描述
M37410E6HFS 8-BIT, UVPROM, 8 MHz, MICROCONTROLLER, CQFP80
M37410M3-XXXFP 8-BIT, MROM, 8 MHz, MICROCONTROLLER, PQFP80
M37410M4-XXXFP 8-BIT, MROM, 8 MHz, MICROCONTROLLER, PQFP80
M37414M5-XXXFP 8-BIT, MROM, 4 MHz, MICROCONTROLLER, PQFP72
M37416M2-XXXFP 8-BIT, MROM, 8 MHz, MICROCONTROLLER, PQFP56
相關代理商/技術參數
參數描述
M37281MKH-XXXSP 制造商:RENESAS 制造商全稱:Renesas Technology Corp 功能描述:SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER with CLOSED CAPTION DECODER and ON-SCREEN DISPLAY CONTROLLER
M372899234 制造商:ITW Switches 功能描述:IN-RUSH
M372F3200DJ3-C 制造商:SAMSUNG 制造商全稱:Samsung semiconductor 功能描述:32M x 72 DRAM DIMM with ECC Using 16Mx4, 4K & 8K Refresh, 3.3V
M372F3280DJ3-C 制造商:SAMSUNG 制造商全稱:Samsung semiconductor 功能描述:32M x 72 DRAM DIMM with ECC Using 16Mx4, 4K & 8K Refresh, 3.3V
M3731 制造商:未知廠家 制造商全稱:未知廠家 功能描述:4 SIRENS & MACHINE GUN 2 LEDS BLINKING