
97
SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER with CLOSED CAPTION DECODER
and ON-SCREEN DISPLAY CONTROLLER
M3727GM6/M8–XXXSP/FP
M37272E8SP/FP
MITSUBISHI MICROCOMPUTERS
Rev. 1.0
Max.
200
4
100
10
0.4
3.0
0.4
0.6
1.3
5
10
VCC = 5.5V,
f(XIN) = 8MHz
(The upper row : M3727GM6/M8)
(The lower row : M37272E8)
VCC = 5.5V, f(XIN) = 0,
f(XCIN) = 32kHz,
OSD OFF, Data slicer OFF,
Low-power dissipation mode set
(CM5 = “0”, CM6 = “1”)
VCC = 5.5 V, f(XIN) = 8 MHz
VCC = 5.5 V, f(XIN) = 0,
f(XCIN) = 32 kHz,
Low-power dissipation mode
set
(CM5 = “0”, CM6 = “1”)
VCC = 5.5V, f(XIN) = 0,
f(XCIN) = 0
VCC = 4.5 V
IOH = –0.5 mA
VCC = 4.5 V
IOL = 0.5 mA
VCC = 4.5 V
IOL = 10.0 mA
VCC = 4.5 V
VCC = 5.0 V
VCC = 5.5 V
VI = 5.5 V
VCC = 5.5 V
VI = 0 V
VCC = 5.5 V
12. ELECTRIC CHARACTERISTICS (VCC = 5 V ± 10 %, VSS = 0 V, f(XIN) = 8 MHz, Ta = –10 °C to 70 °C, unless otherwise noted)
Notes 1: The total current that flows out of the IC must be 20 mA or less.
2: The total input current to IC (IOL1 + IOL2 + IOL3) must be 30 mA or less.
3: The total average input current for ports P30, P31, P24 and P25 to IC must be 20 mA or less.
4: Connect 0.1
F or more capacitor externally between the power source pins VCC–VSS (and AVCC–VSS ) so as to reduce power source noise.
Also connect 0.1
F or more capacitor externally between the pins VCC–CNVSS. ( ) ...M37272E8SP/FP
5: Use a quartz-crystal oscillator or a ceramic resonator for the CPU oscillation circuit. When using the data slicer, use 8 MHz.
6: P06, P07, P15, P23, P24 have the hysteresis when these pins are used as interrupt input pins or timer input pins. P11–P14 have the hysteresis when these
pins are used as multi-master I2C-BUS interface ports. P20–P22 have the hysteresis when these pins are used as serial I/O pins.
7: Pin names in each parameter is described as below.
(1) Dedicated pins: dedicated pin names.
(2) Duble-/triple-function ports
When the same limits: I/O port name.
When the limits of functins except ports are different from I/O port limits: function pin name.
HIGH output voltage
P10–P17, P20–P27,
P30, P31, P52–P55,
LOW output voltage
P00–P07, P10,
P15–P17, P20–P23,
P26, P27, P52–P55
LOW output voltage
P24, P25, P30, P31
LOW output voltage
P11–P14
Hysteresis (See note 6)
____________
RESET, P50, P51, INT1, INT2,
INT3, TIM2, TIM3, SIN, SCLK, SCL1,
SCL2, SDA1, SDA2
HIGH input leak current
P00–P07, P10–P17, P20–P27,
____________
P30, P31, RESET, P50, P51,
LOW input leak current
P00–P07, P10–P17, P20–P27, P30,
____________
P31, P50, P51, RESET
HIGH output leak current
P00–P05 (Only M37272E8SP/FP version)
I2C-BUS BUS switch connection resistor
(between SCL1 and SCL2, SDA1 and SDA2)
ICC
Symbol
Parametear
Test conditions
OSD OFF
Data slicer OFF
OSD ON
Data slicer ON
Stop mode
Wait mode
System operation
Power source current
VOH
VOL
VT+ –VT–
IIZH
IIZL
IOZH
RBS
Test
circuit
1
Min.
2.4
Limits
IOL = 3 mA
IOL = 6 mA
Typ.
60
2
25
1
0.5
2
3
4
5
4
Unit
mA
A
mA
A
V
A
130
6
10
25
(15)
(30)
25
40
(30)
(45)