- 您現在的位置：買賣IC網 > PDF目錄384636 > M37271EFSP (Mitsubishi Electric Corporation) Single Chip 8 Bits Microcomputer(8位單片機) PDF資料下載
參數資料
| 型號： | M37271EFSP |
| 廠商： | Mitsubishi Electric Corporation |
| 英文描述： | Single Chip 8 Bits Microcomputer(8位單片機) |
| 中文描述： | 單芯片8位單片機（8位單片機） |
| 文件頁數： | 81/97頁 |
| 文件大?。?/td> | 1364K |
| 代理商： | M37271EFSP |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁第77頁第78頁第79頁第80頁當前第81頁第82頁第83頁第84頁第85頁第86頁第87頁第88頁第89頁第90頁第91頁第92頁第93頁第94頁第95頁第96頁第97頁
MITSUBISHI MICROCOMPUTERS
M37271MF-XXXSP
M37271EF-XXXSP, M37271EFSP
SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER with CLOSED CAPTION DECODER
and ON-SCREEN DISPLAY CONTROLLER
81
CLOCK GENERATING CIRCUIT
The M37271MF-XXXSP has 2 built-in oscillation circuits. An oscilla-
tion circuit can be formed by connecting a resonator between X
IN
and X
OUT
(X
CIN
and X
COUT
). Use the circuit constants in accordance
with the resonator manufacturer’s recommended values. No exter-
nal resistor is needed between X
IN
and X
OUT
since a feed-back re-
sistor exists on-chip. However, an external feed-back resistor is
needed between X
CIN
and X
COUT
. When using X
CIN
-X
COUT
as sub-
clock, clear bits 5 and 4 of the clock source control register to “0.” To
supply a clock signal externally, input it to the X
IN
(X
CIN
) pin and
make the X
OUT
(X
COUT
) pin open. When not using X
CIN
clock, con-
nect the X
CIN
to V
SS
and make the X
COUT
pin open.
After reset has completed, the internal clock
φ
is half the frequency of
X
IN
. Immediately after poweron, both the X
IN
and X
CIN
clock start
oscillating. To set the internal clock
φ
to low-speed operation mode,
set bit 7 of the CPU mode register (address 00FB
16
) to “1.”
Oscillation Control
(1) Stop mode
The built-in clock generating circuit is shown in Figure 93. When the
STP instruction is executed, the internal clock
φ
stops at “H” level. At
the same time, timers 3 and 4 are connected in hardware and “FF
16
”
is set in the timer 3, “07
16
” is set in the timer 4. Select f(X
IN
)/16 or
f(X
CIN
)/16 as the timer 3 count source (set both bit 0 of the timer
mode register 2 and bit 6 at address 00C7
16
to “0” before the execu-
tion of the STP instruction). And besides, set the timer 3 and timer 4
interrupt enable bits to disabled (“0”) before execution of the STP
instruction. The oscillator restarts when external interrupt is accepted,
however, the internal clock
φ
keeps its “H” level until timer 4 over-
flows. Because this allows time for oscillation stabilizing when a ce-
ramic resonator or a quartz-crystal oscillator is used.
(2) Wait mode
When the WIT instruction is executed, the internal clock
φ
stops in
the “H” level but the oscillator continues running. This wait state is
released at reset or when an interrupt is accepted (Note). Since the
oscillator does not stop, the next instruction can be executed at once.
Note:
In the wait mode, the following interrupts are invalid.
(1) V
SYNC
interrupt
(2) OSD interrupt
(3) Timers 1 and 2 interrupts using P4
2
/TIM2 pin input as count
source
(4) Timer 3 interrupt using P4
3
/TIM3 pin input as count source
(5) Data slicer interrupt
(6) Multi-master I
2
C-BUS interface interrupt
(7) f(X
IN
)/4096 interrupt
(8) All timer interrupts using f(X
IN
)/2 or f(X
CIN
)/2 as count source
(9) All timer interrupts using f(X
IN
)/4096 or f(X
CIN
)/4096 as
count source
(10) A-D conversion interrupt
Fig. 93. Ceramic resonator circuit example
Fig. 94. External clock input circuit example
(3) Low-Speed Mode
If the internal clock is generated from the sub-clock (X
CIN
), a low
power consumption operation can be realized by stopping only the
main clock X
IN
. To stop the main clock, set bit 6 (CM
6
) of the CPU
mode register (00FB
16
) to “1.” When the main clock X
IN
is restarted,
the program must allow enough time to for oscillation to stabilize.
Note that in low-power-consumption mode the X
CIN
-X
COUT
drivability
can be reduced, allowing even lower power consumption (60
μ
A with
f (X
CIN
) = 32kHz). To reduce the X
CIN
-X
COUT
drivability, clear bit 5
(CM
5
) of the CPU mode register (00FB
16
) to “0.” At reset, this bit is
set to “1” and strong drivability is selected to help the oscillation to
start. When an STP instruction is executed, set this bit to “1” by soft-
ware before executing.
X
CIN
X
IN
C
CIN
M37271MF-XXXSP
X
COUT
R
f
R
d
C
COUT
X
OUT
C
IN
C
OUT
X
CIN
M37271MF-XXXSP
External oscillation
circuit or external
pulse
X
COUT
X
IN
X
OUT
Open
Open
External oscillation
circuit
Vcc
Vss
Vcc
Vss
相關PDF資料 |
PDF描述 |
|---|---|
| M37272M6 | Single Chip 8 Bits Microcomputer(8位單片機) |
| M37272E8SP | Single Chip 8 Bits Microcomputer(8位單片機) |
| M37272EFSP | Single Chip 8 Bits Microcomputer(8位單片機) |
| M37272M8 | Single Chip 8 Bits Microcomputer(8位單片機) |
| M37272MA | Single Chip 8 Bits Microcomputer(8位單片機) |
相關代理商/技術參數 |
參數描述 |
|---|---|
| M37271EFSS | 功能描述:EPROM MCU/8BIT CMOS EMULATION CH RoHS:否 類別:編程器，開發系統 >> 配件 系列:- 標準包裝:1 系列:- 附件類型:適配器板 適用于相關產品:RCB230，RCB231，RCB212 配用:26790D-ND - RCB BREAKOUT BOARD RS232 CABLE |
| M37271EF-XXXSP | 制造商:RENESAS 制造商全稱:Renesas Technology Corp 功能描述:SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER with CLOSED CAPTION DECODER and ON-SCREEN DISPLAY CONTROLLER |
| M37271MF | 制造商:RENESAS 制造商全稱:Renesas Technology Corp 功能描述:SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER with CLOSED CAPTION DECODER and ON-SCREEN DISPLAY CONTROLLER |
| M37271MF-213SP | 制造商:MITSUBISHI 制造商全稱:Mitsubishi Electric Semiconductor 功能描述:SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER with CLOSED CAPTION DECODER and ON-SCREEN DISPLAY CONTROLLER |
| M37271MF-219SP | 制造商:MITSUBISHI 制造商全稱:Mitsubishi Electric Semiconductor 功能描述:SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER with CLOSED CAPTION DECODER and ON-SCREEN DISPLAY CONTROLLER |
發布緊急采購，3分鐘左右您將得到回復。