參數資料
型號： M37224M3-050SP
廠商： Mitsubishi Electric Corporation
英文描述： SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER for VOLTAGE SYNTHESIZER with ON-SCREEN DISPLAY CONTROLLER
中文描述： 單芯片8位CMOS微機電壓合成與屏幕顯示控制器
文件頁數： 22/83頁
文件大?。?/td> 901K
代理商： M37224M3-050SP
M37224M3-XXXSP
MITSUBISHI MICROCOMPUTERS
SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER for VOLTAGE SYNTHESIZER
with ON-SCREEN DISPLAY CONTROLLER
22
Fig. 19. Serial I/O Timing (for LSB first)
Synchronous clock
Transfer clock
Serial I/O register
write signal
Serial I/O output
S
OUT
D
0
D
1
D
2
D
3
D
4
D
5
D
6
D
7
(Note)
Serial I/O input
S
IN
Note :
When an internal clock is selected, the S
OUT
pin is at high-impedance after transfer is completed.
Interrupt request bit is set to “1”
Internal clock: The serial I/O counter is set to “7” during the write
cycle into the serial I/O register (address 00DD
16
), and the transfer
clock goes “H” forcibly. At each falling edge of the transfer clock after
the write cycle, serial data is output from the S
OUT
pin. Transfer di-
rection can be selected by bit 5 of the serial I/O mode register. At
each rising edge of the transfer clock, data is input from the S
IN
pin
and data in the serial I/O register is shifted 1 bit.
After the transfer clock has counted 8 times, the serial I/O counter
becomes “0” and the transfer clock stops at HIGH. At this time the
interrupt request bit is set to “1.”
External clock: When an external clock is selected as the clock source,
the interrupt request is set to “1” after the transfer clock has been
counted 8 counts. However, transfer operation does not stop, so the
clock should be controlled externally. Use the external clock of 1MHz
or less with a duty cycle of 50%.
The serial I/O timing is shown in Figure 19. When using an external
clock for transfer, the external clock must be held at HIGH for initial-
izing the serial I/O counter. When switching between an internal clock
and an external clock, do not switch during transfer. Also, be sure to
initialize the serial I/O counter after switching.
Notes 1:
On programming, note that the serial I/O counter is set by
writing to the serial I/O register with the bit managing in-
structions, such as SEB and CLB.
2:
When an external clock is used as the synchronous clock,
write transmit data to the serial I/O register when the trans-
fer clock input level is HIGH.
相關PDF資料
PDF描述
M37224M3 Single Chip 8 Bits Microcomputer(8位單片機)
M37271MF Single Chip 8 Bits Microcomputer(8位單片機)
M37271EF Single Chip 8 Bits Microcomputer(8位單片機)
M37271EFSP Single Chip 8 Bits Microcomputer(8位單片機)
M37272M6 Single Chip 8 Bits Microcomputer(8位單片機)
相關代理商/技術參數
參數描述
M37224M3-XXXSP 制造商:RENESAS 制造商全稱:Renesas Technology Corp 功能描述:SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER for VOLTAGE SYNTHESIZER with ON-SCREEN DISPLAY CONTROLLER
M37225ECSP 制造商:MITSUBISHI 制造商全稱:Mitsubishi Electric Semiconductor 功能描述:SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER for VOLTAGE SYNTHESIZER with ON-SCREEN DISPLAY CONTROLLER
M37225M6 制造商:RENESAS 制造商全稱:Renesas Technology Corp 功能描述:SNGLE-CHIP 8-BIT CMOS MICROCOMPUTER for VOLTAGE SYNTHESIZER with ON-SCREEN DISPLAY CONTROLLER
M37225M8 制造商:RENESAS 制造商全稱:Renesas Technology Corp 功能描述:SNGLE-CHIP 8-BIT CMOS MICROCOMPUTER for VOLTAGE SYNTHESIZER with ON-SCREEN DISPLAY CONTROLLER
M37225MA 制造商:RENESAS 制造商全稱:Renesas Technology Corp 功能描述:SNGLE-CHIP 8-BIT CMOS MICROCOMPUTER for VOLTAGE SYNTHESIZER with ON-SCREEN DISPLAY CONTROLLER
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*