- 您現在的位置：買賣IC網 > PDF目錄45027 > M34552M8H-XXXFP 4-BIT, MROM, 6 MHz, MICROCONTROLLER, PQFP48 PDF資料下載
參數資料
| 型號： | M34552M8H-XXXFP |
| 元件分類： | 微控制器/微處理器 |
| 英文描述： | 4-BIT, MROM, 6 MHz, MICROCONTROLLER, PQFP48 |
| 封裝： | 7 X 10 MM, 0.65 MM PITCH, PLASTIC, QFP-48 |
| 文件頁數： | 106/147頁 |
| 文件大?。?/td> | 1091K |
| 代理商： | M34552M8H-XXXFP |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁第77頁第78頁第79頁第80頁第81頁第82頁第83頁第84頁第85頁第86頁第87頁第88頁第89頁第90頁第91頁第92頁第93頁第94頁第95頁第96頁第97頁第98頁第99頁第100頁第101頁第102頁第103頁第104頁第105頁當前第106頁第107頁第108頁第109頁第110頁第111頁第112頁第113頁第114頁第115頁第116頁第117頁第118頁第119頁第120頁第121頁第122頁第123頁第124頁第125頁第126頁第127頁第128頁第129頁第130頁第131頁第132頁第133頁第134頁第135頁第136頁第137頁第138頁第139頁第140頁第141頁第142頁第143頁第144頁第145頁第146頁第147頁
Rev.3.02
Dec 22, 2006
page 59 of 142
REJ03B0023-0302
4552 Group
(5) External clock
When the external clock signal is used as the main clock (f(XIN)),
connect the XIN pin to the clock source and leave XOUT pin open.
(Figure 52). Do not execute the CRCK instruction in program.
Be careful that the maximum value of the oscillation frequency
when using the external clock differs from the value when using the
ceramic resonator (refer to the recommended operating condition).
Also, note that the power down mode (POF and POF2 instructions)
cannot be used when using the external clock.
(6) Sub-clock generating circuit f(XCIN)
Sub-clock signal f(XCIN) is obtained by externally connecting a
quartz-crystal oscillator. Connect this external circuit and a quartz-
crystal oscillator to pins XCIN and XCOUT at the shortest distance. A
feedback resistor is built in between pins XCIN and XCOUT (Figure 53).
XCIN pin and XCOUT pin are also used as ports D6 and D7, respec-
tively. The sub-clock oscillation circuit is invalid and the function of
ports D6 and D7 are valid by setting bit 2 of register RG to “1”.
When sub-clock, ports D6 and D7 are not used, connect XCIN/D6 to
VSS and leave XCOUT/D7 open.
(7) Clock control register MR
Register MR controls system clock. Set the contents of this register
through register A with the TMRA instruction. In addition, the TAMR
instruction can be used to transfer the contents of register MR to
register A.
(8) Clock control register RG
Register RG controls the start/stop of each oscillation circuit. Set the
contents of this register through register A with the TRGA instruction.
Table 18 Clock control registers
Fig. 52 External clock input circuit
Fig. 53 External quartz-crystal circuit
ROM ORDERING METHOD
1.Mask ROM Order Confirmation Form*
2.Mark Specification Form*
3.Data to be written to ROM... one floppy disk.
* For the mask ROM confirmation and the mark specifications, re-
fer to the “Renesas Technology Corp.” Homepage
(http://www.renesas.com/homepage.jsp).
Note: Externally connect a damping
resistor Rd depending on the
oscillation frequency.
(A feedback resistor is built-in.)
Use the quartz-crystal manu-
facturer’s recommended value
because constants such as ca-
pacitance depend on the
resonator.
MR3
Clock control register MR
Operation mode
Through mode
Frequency divided by 2 mode
Frequency divided by 4 mode
Frequency divided by 8 mode
System clock
f(RING)
f(XIN)
f(XCIN)
Not available (Note 3)
at reset : 11002
at power down : state retained
MR3
0
1
MR1
0
1
R/W
TAMR/
TMRA
Operation mode selection bits
MR2
0
1
0
1
MR0
0
1
0
1
MR2
MR3
System clock selection bits (Note 2)
MR2
Sub-clock (f(XCIN)) oscillation available, ports D6 and D7 not selected
Sub-clock (f(XCIN)) oscillation stop, ports D6 and D7 selected
Main clock (f(XIN)) oscillation available
Main clock (f(XIN)) oscillation stop
On-chip oscillator (f(RING)) oscillation available
On-chip oscillator (f(RING)) oscillation stop
Sub-clock (f(XCIN)) control bit (Note 4)
Main-clock (f(XIN)) control bit (Note 4)
On-chip oscillator (f(RING)) control bit
(Note 4)
0
1
0
1
0
1
Clock control register RG
W
TRGA
at power down : state retained
at reset : 0002
RG2
RG1
RG0
Notes 1: “R” represents read enabled, and “W” represents write enabled.
2: The stopped clock cannot be selected for system clock.
3: “11” cannot be set to the low-order 2 bits (MR1, MR0) of register MR.
4: The oscillation circuit selected for system clock cannot be stopped.
M34552
XIN
XOUT
External oscillation circuit
VDD
VSS
Do not execute the CRCK
instruction in program.
*
M34552
XCIN
XCOUT
Rd
CIN
COUT
相關PDF資料 |
PDF描述 |
|---|---|
| M34553M4-XXXFP | 4-BIT, MROM, 6 MHz, MICROCONTROLLER, PQFP48 |
| M34553M8H-XXXFP | 4-BIT, MROM, 6 MHz, MICROCONTROLLER, PQFP48 |
| M34554MC-XXXFP | 4-BIT, MROM, 6 MHz, MICROCONTROLLER, PQFP64 |
| M34554EDFP | 4-BIT, OTPROM, 6 MHz, MICROCONTROLLER, PQFP64 |
| M3455AG8-XXXFP | 4-BIT, OTPROM, 6 MHz, MICROCONTROLLER, PQFP52 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| M34552M8-XXXFP | 制造商:RENESAS 制造商全稱:Renesas Technology Corp 功能描述:SINGLE-CHIP 4-BIT CMOS MICROCOMPUTER |
| M34552MXH-XXXFP | 制造商:RENESAS 制造商全稱:Renesas Technology Corp 功能描述:SINGLE-CHIP 4-BIT CMOS MICROCOMPUTER |
| M34552MX-XXXFP | 制造商:RENESAS 制造商全稱:Renesas Technology Corp 功能描述:SINGLE-CHIP 4-BIT CMOS MICROCOMPUTER |
| M34553G8FP | 制造商:RENESAS 制造商全稱:Renesas Technology Corp 功能描述:SINGLE-CHIP 4-BIT CMOS MICROCOMPUTER |
| M34553G8HFP | 制造商:RENESAS 制造商全稱:Renesas Technology Corp 功能描述:SINGLE-CHIP 4-BIT CMOS MICROCOMPUTER |
發布緊急采購，3分鐘左右您將得到回復。