參數資料
型號： M30882FHUGP
元件分類： 微控制器/微處理器
英文描述： 32-BIT, FLASH, 32 MHz, MICROCONTROLLER, PQFP144
封裝： 20 X 20 MM, 0.50 MM PITCH, PLASTIC, LQFP-144
文件頁數： 24/60頁
文件大小： 458K
代理商： M30882FHUGP
SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER
MITSUBISHI MICROCOMPUTERS
3826 Group
31
[Transmit Buffer/Receive Buffer Register (TB/
RB)] 001816
The transmit buffer register and the receive buffer register are lo-
cated at the same address. The transmit buffer register is write-
only and the receive buffer register is read-only. If a character bit
length is 7 bits, the MSB of data stored in the receive buffer regis-
ter is “0”.
[Serial I/O1 Status Register (SIO1STS)]
001916
The read-only serial I/O1 status register consists of seven flags
(bits 0 to 6) which indicate the operating status of the serial I/O1
function and various errors.
Three of the flags (bits 4 to 6) are valid only in UART mode.
The receive buffer full flag (bit 1) is cleared to “0” when the receive
buffer is read.
If there is an error, it is detected at the same time that data is
transferred from the receive shift register to the receive buffer reg-
ister, and the receive buffer full flag is set. A write to the serial I/O1
status register clears all the error flags OE, PE, FE, and SE (bit 3
to bit 6, respectively). Writing “0” to the serial I/O1 enable bit SIOE
(bit 7 of the Serial I/O1 Control Register) also clears all the status
flags, including the error flags.
All bits of the serial I/O1 status register are initialized to “0” at re-
set, but if the transmit enable bit (bit 4) of the serial I/O1 control
register has been set to “1”, the transmit shift register shift comple-
tion flag (bit 2) and the transmit buffer empty flag (bit 0) become
“1”.
[Serial I/O1 Control Register (SIO1CON)]
001A16
The serial I/O1 control register contains eight control bits for the
serial I/O1 function.
[UART Control Register (UARTCON)] 001B16
The UART control register consists of four control bits (bits 0 to 3)
which are valid when asynchronous serial I/O is selected and set
the data format of an data transfer. One bit in this register (bit 4) is
always valid and sets the output structure of the P45/TXD pin.
[Baud Rate Generator (BRG)] 001C16
The baud rate generator determines the baud rate for serial trans-
fer.
The baud rate generator divides the frequency of the count source
by 1/(n + 1), where n is the value written to the baud rate genera-
tor.
sNotes on serial I/O
When setting the transmit enable bit to “1”, the serial I/O1 transmit
interrupt request bit is automatically set to “1”. When not requiring
the interrupt occurrence synchronous with the transmission
enalbed, take the following sequence.
Set the serial I/O1 transmit interrupt enable bit to “0” (disabled).
Set the transmit enable bit to “1”.
Set the serial I/O1 transmit interrupt request bit to “0” after 1 or
more instructions have been executed.
Set the serial I/O1 transmit interrupt enable bit to “1” (enabled).
相關PDF資料
PDF描述
M30880FJTGP 32-BIT, FLASH, 32 MHz, MICROCONTROLLER, PQFP100
M30880FWUGP 32-BIT, FLASH, 32 MHz, MICROCONTROLLER, PQFP100
M30882FJTGP 32-BIT, FLASH, 32 MHz, MICROCONTROLLER, PQFP144
M30882FWUGP 32-BIT, FLASH, 32 MHz, MICROCONTROLLER, PQFP144
M308B8SGP 32-BIT, 32 MHz, MICROCONTROLLER, PQFP144
相關代理商/技術參數
參數描述
M30882FJTGP 制造商:RENESAS 制造商全稱:Renesas Technology Corp 功能描述:SINGLE-CHIP 16/32-BIT CMOS MICROCOMPUTER
M30882FJUGP 制造商:RENESAS 制造商全稱:Renesas Technology Corp 功能描述:SINGLE-CHIP 16/32-BIT CMOS MICROCOMPUTER
M30882FWTGP 制造商:RENESAS 制造商全稱:Renesas Technology Corp 功能描述:SINGLE-CHIP 16/32-BIT CMOS MICROCOMPUTER
M30882FWUGP 制造商:RENESAS 制造商全稱:Renesas Technology Corp 功能描述:SINGLE-CHIP 16/32-BIT CMOS MICROCOMPUTER
M308A0SGP 制造商:RENESAS 制造商全稱:Renesas Technology Corp 功能描述:RENESAS MCU
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*