- 您現在的位置：買賣IC網 > PDF目錄45010 > M30245FCGP 16-BIT, FLASH, 16 MHz, MICROCONTROLLER, PQFP100 PDF資料下載
參數資料
| 型號： | M30245FCGP |
| 元件分類： | 微控制器/微處理器 |
| 英文描述： | 16-BIT, FLASH, 16 MHz, MICROCONTROLLER, PQFP100 |
| 封裝： | 14 X 14 MM, 0.50 MM PITCH, PLASTIC, LQFP-100 |
| 文件頁數： | 180/268頁 |
| 文件大?。?/td> | 2520K |
| 代理商： | M30245FCGP |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁第77頁第78頁第79頁第80頁第81頁第82頁第83頁第84頁第85頁第86頁第87頁第88頁第89頁第90頁第91頁第92頁第93頁第94頁第95頁第96頁第97頁第98頁第99頁第100頁第101頁第102頁第103頁第104頁第105頁第106頁第107頁第108頁第109頁第110頁第111頁第112頁第113頁第114頁第115頁第116頁第117頁第118頁第119頁第120頁第121頁第122頁第123頁第124頁第125頁第126頁第127頁第128頁第129頁第130頁第131頁第132頁第133頁第134頁第135頁第136頁第137頁第138頁第139頁第140頁第141頁第142頁第143頁第144頁第145頁第146頁第147頁第148頁第149頁第150頁第151頁第152頁第153頁第154頁第155頁第156頁第157頁第158頁第159頁第160頁第161頁第162頁第163頁第164頁第165頁第166頁第167頁第168頁第169頁第170頁第171頁第172頁第173頁第174頁第175頁第176頁第177頁第178頁第179頁當前第180頁第181頁第182頁第183頁第184頁第185頁第186頁第187頁第188頁第189頁第190頁第191頁第192頁第193頁第194頁第195頁第196頁第197頁第198頁第199頁第200頁第201頁第202頁第203頁第204頁第205頁第206頁第207頁第208頁第209頁第210頁第211頁第212頁第213頁第214頁第215頁第216頁第217頁第218頁第219頁第220頁第221頁第222頁第223頁第224頁第225頁第226頁第227頁第228頁第229頁第230頁第231頁第232頁第233頁第234頁第235頁第236頁第237頁第238頁第239頁第240頁第241頁第242頁第243頁第244頁第245頁第246頁第247頁第248頁第249頁第250頁第251頁第252頁第253頁第254頁第255頁第256頁第257頁第258頁第259頁第260頁第261頁第262頁第263頁第264頁第265頁第266頁第267頁第268頁
M30245 Group
Usage Notes
Rev.2.00
Oct 16, 2006
page 258 of 264
REJ03B0005-0200
Programming Notes
USB
The following Programming Notes should be incorporated into user code, to ensure strict adherence to the USB
protocol for Control Transfers.
(1) In applications requiring high-reliability, we recommend providing the system with protective measures, such as
USB function initialization by software or USB reset by the host, to prevent USB communication from being termi-
nated unexpectedly, for example due to external causes such as noise.
(2) USB2.0 specification stipulates a driver impedance 28 to 44
(see 7.1.1.1 Full-speed (12Mb/s) Driver Characteris-
tics). Connect a serial resistor (recommended value: 27 to 33
) to the USB D+ pin and the USB D- pin to satisfy this
specification. Also connect, if required, a capacitor between the USB D+ pin or USB D-pin and the Vss pin. These
capacitors are to control ringing or adjust the rise and fall times and the crossover point of D+/D-. The numerical
values and configuration of the peripheral components need to be adjusted according to differences in the charac-
teristic impedance and layout of the printed circuit board. on which they are mounted. Therefore, perform careful
evaluation of the system in use and observe the waveforms before deciding on connection or disconnection and
adjusting the values of the resistors and capacitors.
(3) Do not connect the D+ pin or the D- pin to a choke coil.
(4) If the USB Attach/Detach function will not be used, connect the UVcc pin and the USB D+ pin via a 1.5 k
resistor.
(The D+ line pull-up timing depends on the UVcc pin.) If the USB Attach/Detach function is used, connect the P90/
ATTACH pin and the USB D+ pin via a 1.5 k
resistor. Regardless of whether or not the USB Attach/Detach function
is used, connect the UVcc pin to the power supply. In addition, the time required for the host PC to recognize the USB
Attach/Detach state will vary depending state of the system as a whole, including board resistance and capacitance
components, USB cable capacitance, and the board characteristics and processing speed of the host. Perform
careful evaluation of the system in use.
(5) The interrupt service routine (ISR) associated with those USB Function interrupts that are caused by errors must
have execution priority over the ISR for EP0 interrupts. Upon receipt of a USB Function interrupt, the following actions
should be taken:
Step #1: From the USB Interrupt Status (USBIS) and the USB Endpoint 0 Control & Status (EP0CS) registers,
determine if the 'Error Interrupt Status Flag' & the SETUP_END flag (i.e., INTST8 &
EP0CSR5, respectively) are
both set.
[YES] => Set CLR_SETUP_END (EP0CSR11). Go to Step #2.
[NO] => No special S/W action required. Go to Step #1 after the next USB Function interrupt.
Step #2: Is EP0 IN FIFO loading in progress - i.e., data has been written to EP0 IN FIFO, but SET_IN_BUF_RDY
(EP0CSR7) is not yet set?
[YES] => Set SET_IN_BUF_RDY (EP0CSR7). Go to Step #3 after the next EP0 interrupt.
[NO] => No special S/W action required. Go to Step #1 after the next USB Function interrupt.
Step #3: Are OUT_BUF_RDY & SETUP (i.e., EP0CSR0 & EP0CSR2, respectively) set?
[YES] => Go to Step #4.
[NO] => Go to Step #3 after the next EP0 interrupt.
Step #4: Does the current Control Transfer Setup stage DATA0 packet identify a Control Read Transfer?
[YES] => Complete loading EP0 IN FIFO. Set CLR_OUT_BUF_RDY, SET_IN_BUF_RDY, & CLR_SETUP (i.e.,
EP0CSR6, EP0CSR7, & EP0CSR8, respectively). Go to Step #1 after the next USB Function interrupt.
[NO] => Go to Step #3 after the next EP0 interrupt.
Refer to the flowchart in Figure 1.211 for more information on this programming note.
相關PDF資料 |
PDF描述 |
|---|---|
| M30260F3VGP | 16-BIT, FLASH, 20 MHz, MICROCONTROLLER, PQFP48 |
| M30260M3A-XXXGP-U5 | 16-BIT, FLASH, 20 MHz, MICROCONTROLLER, PQFP48 |
| M30260M8A-XXXGP-U5 | 16-BIT, FLASH, 20 MHz, MICROCONTROLLER, PQFP48 |
| M30263F6AFP-U7 | 16-BIT, FLASH, 20 MHz, MICROCONTROLLER, PDSO42 |
| M30263F6AFP-U7 | 16-BIT, FLASH, 20 MHz, MICROCONTROLLER, PDSO42 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| M30245FCGP#U1 | 功能描述:IC M16C/24 MCU FLSH 128K 100LQFP RoHS:是 類別:集成電路 (IC) >> 嵌入式 - 微控制器， 系列:M16C™ M16C/20 標準包裝:1 系列:87C 核心處理器:MCS 51 芯體尺寸:8-位 速度:16MHz 連通性:SIO 外圍設備:- 輸入/輸出數:32 程序存儲器容量:8KB（8K x 8） 程序存儲器類型:OTP EEPROM 大小:- RAM 容量:256 x 8 電壓 - 電源 (Vcc/Vdd):4 V ~ 6 V 數據轉換器:- 振蕩器型:外部 工作溫度:0°C ~ 70°C 封裝/外殼:44-DIP 包裝:管件 其它名稱:864285 |
| M30245FC-XXXFP | 制造商:MITSUBISHI 制造商全稱:Mitsubishi Electric Semiconductor 功能描述:SINGLE-CHIP 16-BIT CMOS MICROCOMPUTER |
| M30245FC-XXXGF | 制造商:MITSUBISHI 制造商全稱:Mitsubishi Electric Semiconductor 功能描述:SINGLE-CHIP 16-BIT CMOS MICROCOMPUTER |
| M30245FC-XXXGP | 制造商:RENESAS 制造商全稱:Renesas Technology Corp 功能描述:SINGLE-CHIP 16-BIT CMOS MICROCOMPUTER |
| M30245FG | 制造商:MITSUBISHI 制造商全稱:Mitsubishi Electric Semiconductor 功能描述:SINGLE-CHIP 16-BIT CMOS MICROCOMPUTER |
發布緊急采購，3分鐘左右您將得到回復。