- 您現在的位置：買賣IC網 > PDF目錄370832 > M30240FA-XXXFP (Mitsubishi Electric Corporation) SINGLE-CHIP 16-BIT CMOS MICROCOMPUTER PDF資料下載
參數資料
| 型號： | M30240FA-XXXFP |
| 廠商： | Mitsubishi Electric Corporation |
| 英文描述： | SINGLE-CHIP 16-BIT CMOS MICROCOMPUTER |
| 中文描述： | 單片16位CMOS微機 |
| 文件頁數： | 47/142頁 |
| 文件大小： | 1637K |
| 代理商： | M30240FA-XXXFP |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁當前第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁第77頁第78頁第79頁第80頁第81頁第82頁第83頁第84頁第85頁第86頁第87頁第88頁第89頁第90頁第91頁第92頁第93頁第94頁第95頁第96頁第97頁第98頁第99頁第100頁第101頁第102頁第103頁第104頁第105頁第106頁第107頁第108頁第109頁第110頁第111頁第112頁第113頁第114頁第115頁第116頁第117頁第118頁第119頁第120頁第121頁第122頁第123頁第124頁第125頁第126頁第127頁第128頁第129頁第130頁第131頁第132頁第133頁第134頁第135頁第136頁第137頁第138頁第139頁第140頁第141頁第142頁
1-47
Mitsubishi microcomputers
M30240 Group
SINGLE-CHIP 16-BIT CMOS MICROCOMPUTER
Preliminary Specifications REV. E
Specifications in this manual are tentative and subject to change
Universal Serial Bus
2.18.2.4 USB SOF Interrupt
The USB SOF (Start-Of-Frame) Interrupt is used to control the transfer of isochronous data. The USB FCU
generates a USB SOF Interrupt request when a start-of-frame packet is received.
Register SOFIC contains the USB SOF Interrupt’s request bit and its interrupt priority select bits, which are
used to enable the interrupt and set its software priority level.
2.18.3 USB Endpoint FIFOs
The USB FCU has an IN (transmit) FIFO and an OUT (receive) FIFO for each endpoint. Each endpoint (ex-
cept endpoint 0) can be configured to support either single packet mode (in which only a single data packet
is allowed to reside in the endpoint’s FIFO) or dual packet mode (in which up to two data packets are allowed
to reside in the endpoint’s FIFO). Dual packet mode provides support for back-to-back transmission or back-
to-back reception. The mode is automatically determined by the MAXP value. When MAXP > 1/2 of the end-
point’s FIFO size, single packet mode is set. When MAXP <= 1/2 of the endpoint’s FIFO size, dual packet
mode is set.
In the event of a bad transmission/reception, the USB FCU handles all the FIFO read/write pointer reversal
and data set management tasks required.
Throughout this specification, the terms “IN FIFO” and “OUT FIFO” usually refer to the FIFOs associated with
a specific endpoint.
2.18.3.1 IN (Transmit) FIFOs
The CPU/DMA writes data to the endpoint’s IN FIFO location specified by the FIFO write pointer, which auto-
matically increments by “1” after a write. The CPU/DMA should only write data to the IN FIFO when the
IN_PKT_RDY bit of the associated IN CSR is a “0”.
Endpoint 0 IN FIFO Operation:
The CPU writes a “1” to the IN_PKT_RDY bit of Endpoint 0 CSR after it finishes writing a packet of data to the
IN FIFO. The USB FCU clears the IN_PKT_RDY bit after the packet has been successfully transmitted to the
host (i.e., ACK is received from the host) or the SETUP_END bit of the IN CSR is set to a “1”.
Endpoint 1-4 IN FIFO Operation when AUTO_SET (bit 7 of Endpoint x IN CSR) = “0” (disabled):
MAXP > 1/2 of the IN FIFO size: The CPU writes a “1” to the IN_PKT_RDY bit of the associated IN CSR after
the CPU/DMAC finishes writing a packet of data to the IN FIFO. The USB FCU clears the IN_PKT_RDY bit
after the packet has been successfully transmitted to the host (which is assumed for isochronous transfers
and is concluded when an ACK is received from the host for non-isochronous transfers).
MAXP <= 1/2 of the IN FIFO size: The CPU writes a “1” to the IN_PKT_RDY bit of the associated IN CSR
after the CPU/DMAC finishes writing a packet of data to the IN FIFO. The USB FCU clears the IN_PKT_RDY
bit as soon as the IN FIFO is ready to accept another data packet. (The FIFO can hold up to two data packets
at the same time in this configuration for back-to-back transmission.)
Endpoint 1-4 IN FIFO Operation when AUTO_SET (bit 7 of Endpoint x IN CSR) = “1” (enabled):
MAXP > 1/2 of the IN FIFO size: When the number of bytes of data equal to the MAXP (maximum packet size)
has been written to the IN FIFO by the CPU/DMAC, the USB FCU sets the IN_PKT_RDY bit of the associated
IN CSR to a “1” automatically. The USB FCU clears the IN_PKT_RDY bit after the packet has been success-
fully transmitted to the host (which is assumed for isochronous transfers and is concluded when an ACK is
received from the host for non-isochronous transfers).
MAXP <= 1/2 of the IN FIFO size: When the number of bytes of data equal to the MAXP (maximum packet
size) has been written to the IN FIFO by the CPU/DMAC, the USB FCU sets the IN_PKT_RDY bit to a “1”
automatically. The USB FCU clears the IN_PKT_RDY bit as soon as the IN FIFO is ready to accept another
data packet. (The FIFO can hold up to two data packets at the same time in this configuration for back-to-back
transmission.)
A software or a hardware flush causes the USB FCU to act as if a packet has been successfully transmitted
out to the host. When there is one packet in the IN FIFO, a flush causes the IN FIFO to be empty. When there
are two packets in the IN FIFO, a flush causes the older packet to be flushed out from the IN FIFO. A flush
also updates the IN FIFO status bits IN_PKT_RDY and TX_NOT_EMPTY of the associated IN CSR.
相關PDF資料 |
PDF描述 |
|---|---|
| M30240FC | SINGLE-CHIP 16-BIT CMOS MICROCOMPUTER |
| M30240M1 | SINGLE-CHIP 16-BIT CMOS MICROCOMPUTER |
| M30240M2 | SINGLE-CHIP 16-BIT CMOS MICROCOMPUTER |
| M30240M3 | SINGLE-CHIP 16-BIT CMOS MICROCOMPUTER |
| M30240M4 | SINGLE-CHIP 16-BIT CMOS MICROCOMPUTER |
相關代理商/技術參數 |
參數描述 |
|---|---|
| M30240FC | 制造商:MITSUBISHI 制造商全稱:Mitsubishi Electric Semiconductor 功能描述:SINGLE-CHIP 16-BIT CMOS MICROCOMPUTER |
| M30240FC-XXXFP | 制造商:MITSUBISHI 制造商全稱:Mitsubishi Electric Semiconductor 功能描述:SINGLE-CHIP 16-BIT CMOS MICROCOMPUTER |
| M30240M1 | 制造商:MITSUBISHI 制造商全稱:Mitsubishi Electric Semiconductor 功能描述:SINGLE-CHIP 16-BIT CMOS MICROCOMPUTER |
| M30240M1-XXXFP | 制造商:MITSUBISHI 制造商全稱:Mitsubishi Electric Semiconductor 功能描述:SINGLE-CHIP 16-BIT CMOS MICROCOMPUTER |
| M30240M2 | 制造商:MITSUBISHI 制造商全稱:Mitsubishi Electric Semiconductor 功能描述:SINGLE-CHIP 16-BIT CMOS MICROCOMPUTER |
發布緊急采購，3分鐘左右您將得到回復。