
1-164
Under
Specifications in this manual are tentative and subject to change
Rev. G
A-D Converter
MITSUBISHI MICROCOMPUTERS
M30222 Group
SINGLE-CHIP 16-BIT CMOS MICROCOMPUTER
(4) Repeat sweep mode 0
In repeat sweep mode 0, the pins selected using the A-D sweep pin select bit are used for repeat
sweep A-D conversion. Table 1.53 shows the specifications of repeat sweep mode 0. Figure 1.132
shows the A-D control register in repeat sweep mode 0.
Table 1.53. Repeat sweep mode 0 specifications
Fig. 1.132. A-D conversion register in repeat sweep mode 0
Item
Specification
Function
The pin selected by the A-D sweep pin select bit are used for repeat sweep A-D
conversion
Start condition
Writing 1 to A-D conversion start flag
Stop condition
Writing 0 to A-D conversion start flag
Interrupt request
generation timing
None generated
Input pin
AN
0
and AN
1
(2 pins), AN
0
and AN
3
(4 pins), AN
0
and AN
5
(6 pins)
,
or AN
0
and AN
1
(8 pins)
Reading A-D
converter results
Read A-D register corresponding to selected pin (at any time)
A-D control register 0 (Note)
Symbol
ADCON0
Address
03D6
16
When reset
00000XXX
2
b7
b6
b5
b4
1 1
b3
b2
b1
b0
Analog input pin
select bit
CH0
Bit symbol
Bit name
Function
CH1
CH2
A-D operation mode
select bit 0
1 1 : Repeat sweep mode 0
MD0
MD1
Trigger select bit
0 : Software trigger
1 : AD
TRG
trigger
0 : A-D conversion disabled
1 : A-D conversion started
0 : f
AD
/4 is selected
1 : f
AD
/2 is selected
TRG
ADST
A-D conversion start flag
Frequency select bit 0
CKS0
W
R
A-D control register 1 (Note 1)
Symbol
ADCON1
Address
03D7
16
When reset
00
16
Bit name
Function
Bit symbol
b7
b6
b5
1
b4
b3
b2
0
b1
b0
A-D sweep pin select bit
SCAN0
SCAN1
MD2
BITS
8/10-bit mode select bit
0 : 8-bit mode
1 : 10-bit mode
0 : f
AD
/2 or f
AD
/4 is selected
1 : f
AD
is selected
VCUT
OPA0
Vref connect bit
0 : Any mode other than repeat sweep mode 1
OPA1
A-D operation mode
select bit 1
1 : Vref connected
External op-amp
connection mode
bit (Note 2)
W
R
Invalid in repeat sweep mode 0
Note 1: If the A-D control register is rewritten during A-D conversion, the conversion result
is indeterminate.
Note 2: Neither
“
01
”
nor
“
10
”
can be selected with the external op-amp connection mode bit.
b4 b3
When single sweep and repeat sweep mode 0
are selected
b1 b0
0
1
( (4 pins)
0
3
0
5
0 0 : AN
0
, AN
7
(6 pins)
0 0 : ANEX0 and ANEX1 are not used
0 1 : ANEX0 input is A-D converted
1 0 : ANEX1 input is A-D converted
1 1 : External op-amp connection mode
b7 b6
Note: If the A-D control register is rewritten during A-D conversion, the conversion result
is indeterminate.
Frequency select bit 1
CKS1