- 您現在的位置：買賣IC網 > PDF目錄45010 > M30100F3FP 16-BIT, FLASH, 16 MHz, MICROCONTROLLER, PQFP32 PDF資料下載
參數資料
| 型號： | M30100F3FP |
| 元件分類： | 微控制器/微處理器 |
| 英文描述： | 16-BIT, FLASH, 16 MHz, MICROCONTROLLER, PQFP32 |
| 封裝： | 7 X 7 MM, 0.80 MM PITCH, PLASTIC, LQFP-32 |
| 文件頁數： | 81/164頁 |
| 文件大?。?/td> | 3302K |
| 代理商： | M30100F3FP |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁第77頁第78頁第79頁第80頁當前第81頁第82頁第83頁第84頁第85頁第86頁第87頁第88頁第89頁第90頁第91頁第92頁第93頁第94頁第95頁第96頁第97頁第98頁第99頁第100頁第101頁第102頁第103頁第104頁第105頁第106頁第107頁第108頁第109頁第110頁第111頁第112頁第113頁第114頁第115頁第116頁第117頁第118頁第119頁第120頁第121頁第122頁第123頁第124頁第125頁第126頁第127頁第128頁第129頁第130頁第131頁第132頁第133頁第134頁第135頁第136頁第137頁第138頁第139頁第140頁第141頁第142頁第143頁第144頁第145頁第146頁第147頁第148頁第149頁第150頁第151頁第152頁第153頁第154頁第155頁第156頁第157頁第158頁第159頁第160頁第161頁第162頁第163頁第164頁
Under
development
Tentative Specifications REV.E1
Specifications in this manual are tentative and subject to change.
Mitsubishi microcomputers
M30100/M30102 Group
SINGLE-CHIP 16-BIT CMOS MICROCOMPUTER
22
System clock control register 0 (Note 1)
Symbol
Address
When reset
CM0
000616
4816
Bit name
Function
Bit symbol
b7
b6
b5
b4 b3
b2
b1
b0
CM07
CM05
CM04
CM03
CM02
CM06
Reserved bit
WAIT peripheral function
clock stop bit
0 : Do not stop peripheral function clock in wait mode
1 : Stop peripheral function clock in wait mode (Note 8)
XCIN-XCOUT drive capacity
select bit (Note 2)
0 : LOW
1 : HIGH
Port XC select bit
0 : I/O port
1 : XCIN-XCOUT generation
Main clock (XIN-XOUT)
stop bit (Note 3,4,5)
0 : On
1 : Off
Main clock division select
bit 0 (Note 7)
0 : CM16 and CM17 valid
1 : Division by 8 mode
System clock select bit
(Note 6)
0 : XIN, XOUT
1 : XCIN, XCOUT
Note 1: Set bit 0 of the protect register (address 000A16) to “1” before writing to this register.
Note 2: Changes to “1” when shifting to stop mode.
Note 3: This bit is used to stop the main clock when placing the device in a low-power mode. If you want to operate with XIN
after exiting from the stop mode, set this bit to “0”. When operating with a self-excited oscillator, set the system clock
select bit (CM07) to “1” before setting this bit to “1”.
Note 4: When inputting external clock, only clock oscillation buffer is stopped and clock input is acceptable.
Note 5: If this bit is set to “1”, XOUT turns “H”. The built-in feedback resistor remains being ON, so XIN turns pulled up to
XOUT (“H”) via the feedback resistor.
Note 6: Set port Xc select bit (CM04) to “1” before setting this bit to “1”. Can not write to both bits at the same time.
Note 7: This bit changes to “1” when shifting from high-speed/medium-speed mode to stop mode and at a reset. When shifting from
low-speed/low power dissipation mode to stop mode, the value before stop mode is retained.
Note 8: fc32 is not included. Do not set to “1” when using low-speed, low power dissipation or ring oscillator mode.
System clock control register 1 (Note 1)
Symbol
Address
When reset
CM1
000716
2016
Bit name
Function
Bit symbol
b7
b6
b5
b4 b3
b2
b1
b0
CM10
All clock stop control bit
(Note 4)
0 : Clock on
1 : All clocks off (stop mode)
CM15
XIN-XOUT drive capacity
select bit (Note 2)
0 : LOW
1 : HIGH
W
R
W
R
CM16
CM17
Reserved bit
Always set to
“0”
Ring oscillation stop bit
0 : Oscillation enabled
1 : Oscillation stopped (Note 5)
Main clock division
select bit 1 (Note 3)
0 0 : No division mode
0 1 : Division by 2 mode
1 0 : Division by 4 mode
1 1 : Division by 16 mode
b7 b6
0
Reserved bit
0 : Ceramic oscillation or crystal oscillation
1 : RC oscillation
XIN oscillation select bit
Always set to
“0”
0
Note 1: Set bit 0 of the protect register (address 000A16) to “1” before writing to this register.
Note 2: This bit changes to “1” when shifting from high-speed/middle-speed mode to stop mode or at reset. When shifting from
low-speed/low power dissipation mode to stop mode, the value before stop mode is retained.
Note 3: Can be selected when bit 6 of the system clock control register 0 (address 000616) is “0”. If “1”, division mode is fixed at 8.
Note 4: If this bit is set to “1”, XOUT turns “H”, and the built-in feedback resistor is ineffective. The mode of power control cannot
be shifted to the stop mode directly from the oscillator mode.
Note 5: This bit can be set to “1” only when both the main clock switch bit (CM22) and clock monitor bit (CM23) are set to “0” .
Moreover, this bit is automatically set to “0” if the main clock switch bit (CM22) is set to “1”.
Always set to
“0”
00
CM13
CM14
Clock Generating Circuit
Figure 1.8.4. System clock control registers 0 and 1
相關PDF資料 |
PDF描述 |
|---|---|
| M30102M3T-XXXFP | 16-BIT, MROM, 16 MHz, MICROCONTROLLER, PQFP48 |
| M30102M3-XXXFP | 16-BIT, MROM, 16 MHz, MICROCONTROLLER, PQFP48 |
| M30100M3-XXXFP | 16-BIT, MROM, 16 MHz, MICROCONTROLLER, PQFP32 |
| M30100F3TFP | 16-BIT, FLASH, 16 MHz, MICROCONTROLLER, PQFP32 |
| M30102M2T-XXXFP | 16-BIT, MROM, 16 MHz, MICROCONTROLLER, PQFP48 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| M30100T3-RPD-E | 制造商:Renesas Electronics Corporation 功能描述:DEV EMULATOR POD M16C/10 SERIES - Bulk |
| M30100T-PTC | 制造商:RENESAS 制造商全稱:Renesas Technology Corp 功能描述:Converter for Connecting 32-pin 0.8mm-pitch QFP for M30100T-PRB (for M16C/10 Group M30100) |
| M30-1010046 | 功能描述:集管和線殼 1.25MM FEMALE CRIMP TIN PK OF 105 RoHS:否 產品種類:1.0MM Rectangular Connectors 產品類型:Headers - Pin Strip 系列:DF50 觸點類型:Pin (Male) 節距:1 mm 位置/觸點數量:16 排數:1 安裝風格:SMD/SMT 安裝角:Right 端接類型:Solder 外殼材料:Liquid Crystal Polymer (LCP) 觸點材料:Brass 觸點電鍍:Gold 制造商:Hirose Connector |
| M3010102636207.32LLZZ | 制造商:3M Electronic Products Division 功能描述:QUOTE # V05-0068 |
| M30102 | 制造商:RENESAS 制造商全稱:Renesas Technology Corp 功能描述:SINGLE-CHIP 16-BIT CMOS MICROCOMPUTER |
發布緊急采購，3分鐘左右您將得到回復。