- 您現在的位置：買賣IC網 > PDF目錄358968 > LZ23H3V1 (Sharp Corporation) SOCKET, D, FILTERED, 330PF, 44WAY; Connector type:D Sub, High-Density; Gender:Socket; Ways, No. of:44; Termination method:Solder; Material, contact:Copper Alloy; Plating, contact:Bright Tin; Series:FHTB; Material:Steel; Current RoHS Compliant: Yes PDF資料下載
參數資料
| 型號： | LZ23H3V1 |
| 廠商： | Sharp Corporation |
| 英文描述： | SOCKET, D, FILTERED, 330PF, 44WAY; Connector type:D Sub, High-Density; Gender:Socket; Ways, No. of:44; Termination method:Solder; Material, contact:Copper Alloy; Plating, contact:Bright Tin; Series:FHTB; Material:Steel; Current RoHS Compliant: Yes |
| 中文描述： | 1/3-type隔行彩色CCD傳感器的面積1 090萬像素 |
| 文件頁數： | 4/20頁 |
| 文件大小： | 155K |
| 代理商： | LZ23H3V1 |
LZ23H3V1
4
CHARACTERISTICS
(Drive method : 1/30 s frame accumulation)
(T
A
= +25 C, Operating conditions : The typical values specified in "
RECOMMENDED OPERATING CONDITIONS
".
Color temperature of light source : 3 200 K, IR cut-off filter (CM-500, 1 mmt) is used.)
PARAMETER
SYMBOL
Standard output voltage
Photo response non-uniformity
MIN.
TYP.
150
MAX.
UNIT
mV
%
mV
mV
NOTE
2
3
4
5
V
O
PRNU
10
Saturation output voltage
V
SAT
450
330
530
410
Dark output voltage
Dark signal non-uniformity
Sensitivity (green channel)
Smear ratio
Image lag
V
DARK
DSNU
R
SMR
AI
0.5
0.5
150
–75
3.0
2.0
mV
mV
mV
dB
%
1, 6
1, 7
8
9
10
105
–65
1.0
NOTES :
Within the recommended operating conditions of V
OD
,
V
OFD
of the internal output satisfies with ABL larger than
500 times exposure of the standard exposure conditions,
and V
SAT
larger than 330 mV.
1. T
A
= +60 C
2. The average output voltage of G signal under uniform
illumination. The standard exposure conditions are
defined as when Vo is 150 mV.
3. The image area is divided into 10 x 10 segments under
the standard exposure conditions. Each segment's
voltage is the average output voltage of all pixels within
the segment. PRNU is defined by (Vmax – Vmin)/Vo,
where Vmax and Vmin are the maximum and minimum
values of each segment's voltage respectively.
4. The image area is divided into 10 x 10 segments. Each
segment's voltage is the average output voltage of all
pixels within the segment. V
SAT
is the minimum
segment's voltage under 10 times exposure of the
standard exposure conditions. The operation of OFDC is
high. (for still image capturing)
5. The image area is divided into 10 x 10 segments. Each
segment's voltage is the average output voltage of all
pixels within the segment. V
SAT
is the minimum
segment's voltage under 10 times exposure of the
standard exposure conditions. The operation of OFDC is
low.
6. The average output voltage under non-exposure
conditions.
7. The image area is divided into 10 x 10 segments under
non-exposure conditions. DSNU is defined by (Vdmax –
Vdmin), where Vdmax and Vdmin are the maximum and
minimum values of each segment's voltage respectively.
8. The average output voltage of G signal when a 1 000
lux light source with a 90% reflector is imaged by a lens
of F4, f50 mm.
9. The sensor is exposed only in the central area of V/10
square with a lens at F4, where V is the vertical image
size. SMR is defined by the ratio of the output voltage
detected during the vertical blanking period to the
maximum output voltage in the V/10 square.
10. The sensor is exposed at the exposure level
corresponding to the standard conditions. AI is defined
by the ratio of the output voltage measured at the 1st
field during the non-exposure period to the standard
output voltage.
11. The sensor is exposed only in the central area of V/10
square, where V is the vertical image size. ABL is
defined by the ratio of the exposure at the standard
conditions to the exposure at a point where blooming is
observed.
12. The sensor is exposed at the exposure level
corresponding to the standard conditions. LCR is defined
by (V
G
/V
O
) x 100, where V
G
is the difference
between the average output voltage of G signal at the
1st field, and that of G signal at the 2nd field.
11
500
ABL
I
OD
LCR
Blooming suppression ratio
Output transistor drain current
Line crawling
4.0
8.0
3.0
mA
%
12
相關PDF資料 |
PDF描述 |
|---|---|
| LZ2413 | 1/4-type Color CCD Area Sensors with 270 k Pixels |
| LZ2413H | 1/4-type Color CCD Area Sensors with 270 k Pixels |
| LZ2416J | Dual-power-supply (5 V/12 V) Operation 1/4-type B/W CCD Area Sensor with 270 k Pixels |
| LZ2423H | 1/4-type Color CCD Area Sensor with 320 k Pixels |
| LZ2426J | Dual-power-supply (5 V/12 V) Operation 1/4-type B/W CCD Area Sensor with 320 k Pixels |
相關代理商/技術參數 |
參數描述 |
|---|---|
| LZ23J3N | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:AREA CCD IMAGE ARRAY |
| LZ23J3V | 制造商:SHARP 制造商全稱:Sharp Electrionic Components 功能描述:1/2.7-type Interline Color CCD Area Sensor with 1 310 k Pixels |
| LZ23K | 制造商:ebm-papst Inc 功能描述:GUARD FINGER 92MM 制造商:ebm-papst Inc 功能描述:GUARD, FINGER, 92MM 制造商:ebm-papst Inc 功能描述:FINGER GUARD, 92MM; For Use With:Ebm Papst 3xxx Series Fans; Fan Size:92mm; Fixing Centers:82.5mm; Guard Material:Steel; Accessory Type:Finger Guard; Color:Bright zinc; External Height:92mm; External Width:92mm; Material:Metal ;RoHS Compliant: Yes 制造商:ebm-papst Inc 功能描述:Metal finger guard, 92x92mm |
| LZ23K | 制造商:UNBRANDED 功能描述:FINGER GUARD 92MM |
| LZ24 | 功能描述:風扇電線及配件 METAL FINGER GUARD RoHS:否 制造商:ebm-papst 類型:Finger Guard 適合風扇大小:120 mm 系列: |
發布緊急采購，3分鐘左右您將得到回復。