- 您現在的位置：買賣IC網 > PDF目錄98003 > LW006F-LP (LINEAGE POWER LLC) 1-OUTPUT 6 W DC-DC REG PWR SUPPLY MODULE PDF資料下載
參數資料
| 型號： | LW006F-LP |
| 廠商： | LINEAGE POWER LLC |
| 元件分類： | 電源模塊 |
| 英文描述： | 1-OUTPUT 6 W DC-DC REG PWR SUPPLY MODULE |
| 封裝： | DIP-18 |
| 文件頁數： | 9/12頁 |
| 文件大?。?/td> | 352K |
| 代理商： | LW006F-LP |
6
Lineage Power
Advance Data Sheet
April 2008
36 Vdc to 75 Vdc Inputs, 6 W
LW006-Series Power Modules:
Test Configurations
8-203(C).n
Note: Input reflected-ripple current is measured with a simulated
source impedance of 12 H. Capacitor Cs offsets possible
battery impedance. Current is measured at the input of the
module.
Figure 1. Input Reflected-Ripple Test Setup
8-513(C).r
Note: Use one 0.1 F ceramic capacitor. Scope measurement should
be made using a BNC socket. Position the load between 50
mm and 75 mm (2 in. and 3 in.) from the module.
Figure 2. Peak-to-Peak Output Noise Measurement
Test Setup for Single Outputs
8-204(C)
Note: All measurements are taken at the module terminals. When
socketing, place Kelvin connections at module terminals to
avoid measurement errors due to socket contact resistance.
Figure 3. Output Voltage and Efficiency
Measurement Test Setup for Single
Outputs
Design Considerations
Input Source Impedance
The power module should be connected to a low
ac-impedance input source. Highly inductive source
impedances can affect the stability of the power mod-
ule. If the source inductance exceeds 10 H, a 33 F
electrolytic capacitor (ESR < 0.7 at 100 kHz)
mounted close to the power module helps ensure
stability of the unit.
Safety Considerations
For safety-agency approval of the system in which the
power module is used, the power module must be
installed in compliance with the spacing and separation
requirements of the end-use safety agency standard,
i.e., UL 1950, CSA C22.2 No. 950-95, and VDE 0805
(EN60950, IEC950).
If the input source is non-SELV (ELV or a hazardous
voltage greater than 60 Vdc and less than or equal to
75 Vdc), for the module's output to be considered
meeting the requirements of safety extra-low voltage
(SELV), all of the following must be true:
n
The input source is to be provided with reinforced
insulation from any other hazardous voltages, includ-
ing the ac mains.
n
One VI pin and one VO pin are to be grounded or
both the input and output pins are to be kept floating.
n
The input pins of the module are not operator acces-
sible.
n
Another SELV reliability test is conducted on the
whole system, as required by the safety agencies, on
the combination of supply source and the subject
module to verify that under a single fault, hazardous
voltages do not appear at the module's output.
Note: Do not ground either of the input pins of the
module without grounding one of the output
pins. This may allow a non-SELV voltage to
appear between the output pins and ground.
The power module has extra-low voltage (ELV) outputs
when all inputs are ELV.
The input to these units is to be provided with a maxi-
mum 5 A normal-blow fuse in the ungrounded lead.
TO OSCILLOSCOPE
12 H
CS 220 F
IMPEDANCE < 0.1
Ω
@ 20 C, 100 kHz
VI(+)
VI(-)
BATTERY
33 F
LTEST
V O (+)
V O (-)
0.1 F
RESISTIVE
LOAD
SCOPE
COPPER STRIP
VI(+)
VI(-)
VO(+)
VO(-)
II
IO
SUPPLY
CONTACT RESISTANCE
CONTACT AND
DISTRIBUTION LOSSES
LOAD
η
VO(+) VO(–)
–
[]IO
VI(+) VI(–)
–
[]II
------------------------------------------------
100
×
=
%
相關PDF資料 |
PDF描述 |
|---|---|
| LW006A-LP | 1-OUTPUT 6 W DC-DC REG PWR SUPPLY MODULE |
| LX1571IDMT | 1 A SWITCHING CONTROLLER, PDSO8 |
| LX1570IDMT | 1 A SWITCHING CONTROLLER, PDSO8 |
| LX1676-CLQT | 1.5 A SWITCHING CONTROLLER, 1100 kHz SWITCHING FREQ-MAX, PQCC38 |
| LX1677-CPW | 1.5 A SWITCHING CONTROLLER, 1100 kHz SWITCHING FREQ-MAX, PDSO38 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| LW010 | 制造商:MA-COM 制造商全稱:M/A-COM Technology Solutions, Inc. 功能描述:Power Modules: 18 Vdc to 36 Vdc or 36 Vdc to 75 Vdc Inputs, 10 W and 15 W |
| LW010A | 功能描述:DC/DC轉換器 10W, IN 36-75V OUT 5V RoHS:否 制造商:Murata 產品: 輸出功率: 輸入電壓范圍:3.6 V to 5.5 V 輸入電壓（標稱）: 輸出端數量:1 輸出電壓（通道 1）:3.3 V 輸出電流（通道 1）:600 mA 輸出電壓（通道 2）: 輸出電流（通道 2）: 安裝風格:SMD/SMT 封裝 / 箱體尺寸: |
| LW010A1 | 功能描述:CONVERTER DC/DC 5V 10W OUT RoHS:否 類別:電源 - 板載 >> DC DC Converters 系列:LW010 設計資源:VI-200, VI-J00 Design Guide, Appl Manual 標準包裝:1 系列:* 類型:隔離 輸出數:1 電壓 - 輸入（最?。?42V 電壓 - 輸入（最大）:60V Voltage - Output 1:15V Voltage - Output 2:- Voltage - Output 3:- 電流 - 輸出（最大）:* 電源（瓦） - 制造商系列:150W 電壓 - 隔離:* 特點:* 安裝類型:通孔 封裝/外殼:9-SlimMod 尺寸/尺寸:4.60" L x 1.80" W x 0.52" H（116.8mm x 45.7mm x 13.2mm） 包裝:散裝 工作溫度:-55°C ~ 85°C 效率:* 電源（瓦特）- 最大:* |
| LW010A2 | 功能描述:CONVERTER DC/DC 5V 10W OUT RoHS:否 類別:電源 - 板載 >> DC DC Converters 系列:LW010 設計資源:VI-200, VI-J00 Design Guide, Appl Manual 標準包裝:1 系列:* 類型:隔離 輸出數:1 電壓 - 輸入（最?。?42V 電壓 - 輸入（最大）:60V Voltage - Output 1:15V Voltage - Output 2:- Voltage - Output 3:- 電流 - 輸出（最大）:* 電源（瓦） - 制造商系列:150W 電壓 - 隔離:* 特點:* 安裝類型:通孔 封裝/外殼:9-SlimMod 尺寸/尺寸:4.60" L x 1.80" W x 0.52" H（116.8mm x 45.7mm x 13.2mm） 包裝:散裝 工作溫度:-55°C ~ 85°C 效率:* 電源（瓦特）- 最大:* |
| LW010A4 | 功能描述:DC/DC轉換器 10W, IN 36-75V OUT 5V, POSITIVE RoHS:否 制造商:Murata 產品: 輸出功率: 輸入電壓范圍:3.6 V to 5.5 V 輸入電壓（標稱）: 輸出端數量:1 輸出電壓（通道 1）:3.3 V 輸出電流（通道 1）:600 mA 輸出電壓（通道 2）: 輸出電流（通道 2）: 安裝風格:SMD/SMT 封裝 / 箱體尺寸: |
發布緊急采購，3分鐘左右您將得到回復。