參數資料
型號： LV8731V
元件分類： 運動控制電子
英文描述： STEPPER MOTOR CONTROLLER, PDSO44
封裝： 0.275 INCH, SSOP-44
文件頁數： 3/26頁
文件大?。?/td> 336K
代理商： LV8731V
LV8731V
No.A1482-11/26
(4) Setting constant-current control reference current
This IC is designed to automatically exercise PWM constant-current chopping control for the motor current by setting
the output current. Based on the voltage input to the VREF pin and the resistance connected between RF and GND,
the output current that is subject to the constant-current control is set using the calculation formula below :
IOUT = (VREF/5)/RF resistance
* The above setting is the output current at 100% of each excitation mode.
The voltage input to the VREF pin can be switched to four-step settings depending on the statuses of the two inputs,
ATT1 and ATT2. This is effective for reducing power consumption when motor holding current is supplied.
Attenuation function for VREF input voltage
ATT1
ATT2
Current setting reference voltage attenuation ratio
Low
100%
High
Low
80%
Low
High
50%
High
20%
The formula used to calculate the output current when using the function for attenuating the VREF input voltage is
given below.
IOUT = (VREF/5) × (attenuation ratio)/RF resistance
Example : At VREF of 1.5V, a reference voltage setting of 100% [(ATT1, ATT2) = (L, L)] and an RF resistance of
0.3
Ω, the output current is set as shown below.
IOUT = 1.5V/5 × 100%/0.3Ω = 1.0A
If, in this state, (ATT1, ATT2) is set to (H, H), IOUT will be as follows :
IOUT = 1.0A × 20% = 200mA
In this way, the output current is attenuated when the motor holding current is supplied so that power can
be conserved.
(5) Blanking period
If, when exercising PWM constant-current chopping control over the motor current, the mode is switched from decay
to charge, the recovery current of the parasitic diode may flow to the current sensing resistance, causing noise to be
carried on the current sensing resistance pin, and this may result in erroneous detection. To prevent this erroneous
detection, a blanking period is provided to prevent the noise occurring during mode switching from being received.
During this period, the mode is not switched from charge to decay even if noise is carried on the current sensing
resistance pin.
In the stepping motor driver mode (DM = Low or Open) of this IC, the blanking time is fixed at approximately 1
μs.
In the DC motor driver mode (DM = High), the blanking time can be switched to one of two levels using the
RST/BLK pin. (Refer to "Blanking time switching function.")
相關PDF資料
PDF描述
LV8743V 0.8 A SWITCHING CONTROLLER, 440 kHz SWITCHING FREQ-MAX, PDSO44
LV8743V 0.8 A SWITCHING CONTROLLER, 440 kHz SWITCHING FREQ-MAX, PDSO44
LV8746V STEPPER MOTOR CONTROLLER, 1.2 A, PDSO44
LV8746V STEPPER MOTOR CONTROLLER, 1.2 A, PDSO44
LV8747T 1.75 A SWITCHING CONTROLLER, 150 kHz SWITCHING FREQ-MAX, PQFP64
相關代理商/技術參數
參數描述
LV8731VGEVB 功能描述:電源管理IC開發工具 EVM FOR LV8731V RoHS:否 制造商:Maxim Integrated 產品:Evaluation Kits 類型:Battery Management 工具用于評估:MAX17710GB 輸入電壓: 輸出電壓:1.8 V
LV8731V-MPB-H 功能描述:馬達/運動/點火控制器和驅動器 RoHS:否 制造商:STMicroelectronics 產品:Stepper Motor Controllers / Drivers 類型:2 Phase Stepper Motor Driver 工作電源電壓:8 V to 45 V 電源電流:0.5 mA 工作溫度:- 25 C to + 125 C 安裝風格:SMD/SMT 封裝 / 箱體:HTSSOP-28 封裝:Tube
LV8731V-TLM-H 功能描述:馬達/運動/點火控制器和驅動器 9-32VSteppingMotor 2chBrush Motor Dr RoHS:否 制造商:STMicroelectronics 產品:Stepper Motor Controllers / Drivers 類型:2 Phase Stepper Motor Driver 工作電源電壓:8 V to 45 V 電源電流:0.5 mA 工作溫度:- 25 C to + 125 C 安裝風格:SMD/SMT 封裝 / 箱體:HTSSOP-28 封裝:Tube
LV8732V 制造商:SANYO 制造商全稱:Sanyo Semicon Device 功能描述:PWM Constant-Current Control Stepping Motor Driver
LV8732V_10 制造商:SANYO 制造商全稱:Sanyo Semicon Device 功能描述:PWM Constant-Current Control Stepping Motor Driver
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*