- 您現在的位置：買賣IC網 > PDF目錄45001 > LV51140T 2-CHANNEL POWER SUPPLY SUPPORT CKT, PDSO6 PDF資料下載
參數資料
| 型號： | LV51140T |
| 元件分類： | 電源管理 |
| 英文描述： | 2-CHANNEL POWER SUPPLY SUPPORT CKT, PDSO6 |
| 封裝： | SOT-23, 6 PIN |
| 文件頁數： | 13/13頁 |
| 文件大?。?/td> | 155K |
| 代理商： | LV51140T |
LV51140T
No.A1024-9/13
Over-discharge detection
When the battery voltage (VDD) under the normal condition becomes equal to or less than the over-discharge detection
voltage (Vdc) and that state continues for more than the over-discharge detection time (tdc), this IC turns off the
discharge control FET and stops discharging. This state is called the over-discharge detection condition. Recovery from
the over-discharge detection condition is achieved only by connecting the charger.
Return from over-discharge
When the charger is connected and charging starts, the charge current flows through the internal parasitic diode of the
discharge control FET. If the VM terminal voltage is higher than the charge over-current detection voltage (VIc), the IC
returns to the normal condition when VDD becomes equal to or higher than VRdc and this state continues more than the
delay time1 (trel1).
If the VM terminal voltage is lower than the charge over-current detection voltage (VIc), same as the above-mentioned
case, the IC returns to the normal condition when VDD becomes equal to or higher than Vdc and this state continues
more than the delay time1 (trel1).
This IC stops all internal circuits (Shutdown condition) after detecting the over-discharge and reduces current
consumption. (Max 0.1
μA, at VDD = 1.8V)
0V battery charge function
If the voltage of charger (the voltage between VDD and VM) is larger than the 0V battery charge starting charger
voltage (Vcha), 0V battery charge becomes possible when CO terminal outputs VDD terminal potential and turns on the
charge control FET.
相關PDF資料 |
PDF描述 |
|---|---|
| LV5254LG | SPECIALTY ANALOG CIRCUIT, PBGA24 |
| LV5254LG | SPECIALTY ANALOG CIRCUIT, PBGA24 |
| LV5603T | SWITCHING CONTROLLER, 520 kHz SWITCHING FREQ-MAX, PQFP48 |
| LV5603T | SWITCHING CONTROLLER, 520 kHz SWITCHING FREQ-MAX, PQFP48 |
| LV5681P | 1-CHANNEL POWER SUPPLY SUPPORT CKT, PZFM15 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| LV51140T-TE-F-E | 功能描述:電池管理 RoHS:否 制造商:Texas Instruments 電池類型:Li-Ion 輸出電壓:5 V 輸出電流:4.5 A 工作電源電壓:3.9 V to 17 V 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:VQFN-24 封裝:Reel |
| LV51141T | 制造商:SANYO 制造商全稱:Sanyo Semicon Device 功能描述:CMOS IC 1-Cell Lithium-Ion Battery Protection IC |
| LV51141T-TE-F-E | 功能描述:電池管理 RoHS:否 制造商:Texas Instruments 電池類型:Li-Ion 輸出電壓:5 V 輸出電流:4.5 A 工作電源電壓:3.9 V to 17 V 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:VQFN-24 封裝:Reel |
| LV51142T | 制造商:SANYO 制造商全稱:Sanyo Semicon Device 功能描述:CMOS IC 1-Cell Lithium-Ion Battery Protection IC |
| LV51142T-TE-F-E | 功能描述:電池管理 RoHS:否 制造商:Texas Instruments 電池類型:Li-Ion 輸出電壓:5 V 輸出電流:4.5 A 工作電源電壓:3.9 V to 17 V 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:VQFN-24 封裝:Reel |
發布緊急采購，3分鐘左右您將得到回復。