- 您現在的位置：買賣IC網 > PDF目錄367613 > LUCL8576BP-DT Dual Ringing SLIC PDF資料下載
參數資料
| 型號： | LUCL8576BP-DT |
| 英文描述： | Dual Ringing SLIC |
| 中文描述： | 雙振鈴用戶接口 |
| 文件頁數： | 9/26頁 |
| 文件大?。?/td> | 583K |
| 代理商： | LUCL8576BP-DT |
Agere Systems Inc.
9
Data Sheet
May 2001
L8576B Dual Ringing SLIC
Operating States
(continued)
These states are selected using three logic inputs, B2, RNGNG, and NDISC. B2 sets normal operation, either with
forward or reverse battery. RNGNG overrides B2 and applies ringing with the polarity of tip and ring reversed on
edges of the B2 signal. The slope of the waveform is determined by a resistor from RRNG to AGND. Logic input
NDISC puts the device into a loop current denial state (disconnect). Tip and ring amplifiers are saturated against
ground with about a 100
μ
A current source. This creates a level in the loop current sensing circuitry that
approaches a loop closed state. Some conditions on the tip and ring could cause the circuit to indicate loop closed
even though the loop is open. This situation can be prevented by connecting a 300 k
resistor from V
BAT
to each of
the outputs of the tip and ring amplifiers (see Figure 2). This will pull the amplifier output to about 30 V above V
BAT
,
keeping the NSTAT output at a steady high (on-hook indication) level. If the disconnect state is not used or the
NSTAT output during the disconnect state is not recognized or used, then the resistors are not needed.
Table 2 below summarizes the operating input state coding.
Absolute Maximum Ratings
(at T
A
= 25
°
C)
Stresses in excess of the absolute maximum ratings can cause permanent damage to the device. These are abso-
lute stress ratings only. Functional operation of the device is not implied at these or any other conditions in excess
of those given in the operational sections of the data sheet. Exposure to absolute maximum ratings for extended
periods can adversely affect device reliability.
Note: The IC can be damaged unless all ground connections are applied before, and removed after, all other connections. Furthermore, when
powering the device, the user must guarantee that no external potential creates a voltage on any pin of the device that exceeds its rat-
ings. For example, inductance in a supply lead could resonate with the supply filter capacitor to cause a destructive overvoltage.
Table 2. Input State Coding
NDISC
1
1
1
RNGNG B2
0
0
1
State
1
0
Forward Battery, Normal Talk, and Feed State.
Pin PT is positive with respect to PR.
Reverse Battery, Normal Talk, and Feed State.
Pin PT is negative with respect to PR.
1
↑
Ringing Is Applied to PT and PR.
On the transition, PT starts towards a positive volt-
age (with respect to PR). The endpoint of this state is PT at BGND and PR at V
BAT
.
0
↓
Ringing Is Applied to PT and PR.
On the transition, PT starts towards a negative volt-
age (with respect to PR). The endpoint of this state is PT at V
BAT
and PR at BGND.
0/1
Disconnect State.
The tip and ring amplifiers are turned off, and the SLIC goes into a
high-impedance state (>100 k
).
1
1
0
0/1
Parameter
Symbol
V
CC
V
BAT
—
—
—
—
—
—
T
stg
—
—
—
—
Min
–0.5
–75
–0.5
—
–0.5
—
–7.0
—
–40
5
—
V
BAT
– 5
V
BAT
– 15
Typ
—
—
—
±
20
—
±
35
—
165
—
—
±
3
—
—
Max
7.0
0.5
Unit
V
V
V
mA
V
mA
V
°
C
°
C
%
V
V
V
5 V dc Supplies
Office Battery Supply
Logic Input Voltage
Logic Input Clamp Diode Current, per Pin
Logic Output Voltage
Logic Output Current, per Pin
Analog Input Voltage
Maximum Junction Temperature
Storage Temperature Range
Relative Humidity Range (noncondensing)
Ground Potential Difference (BGND to AGND)
PT or PR Fault Voltage (dc)
PT or PR Fault Voltage (10 μs x 1000 μs)
V
CC
+ 0.5
—
V
CC
+ 0.5
—
7.0
—
125
95
—
3
15
相關PDF資料 |
PDF描述 |
|---|---|
| LUCL9214AAJ-D | GT 19C 19#12 PIN RECP |
| LUCL9214AAJ-DT | Circular Connector; MIL SPEC:MIL-C-5015; Body Material:Metal; Series:GT; No. of Contacts:2; Connector Shell Size:24; Connecting Termination:Solder; Circular Shell Style:Square Flange Receptacle; Body Style:Straight |
| LUCL9214GAJ-D | Low-Cost Ringing SLIC |
| LUCL9214GAJ-DT | Low-Cost Ringing SLIC |
| LUCL9214GAU-D | Low-Cost Ringing SLIC |
相關代理商/技術參數 |
參數描述 |
|---|---|
| LUCL9214AA-DT | 制造商:AGERE 制造商全稱:AGERE 功能描述:Low-Cost Ringing SLIC |
| LUCL9214AAJ-D | 制造商:AGERE 制造商全稱:AGERE 功能描述:Low-Cost Ringing SLIC |
| LUCL9214AAJ-DT | 制造商:AGERE 制造商全稱:AGERE 功能描述:Low-Cost Ringing SLIC |
| LUCL9214AAU-D | 制造商:AGERE 制造商全稱:AGERE 功能描述:Low-Cost Ringing SLIC |
| LUCL9214ARG-D | 制造商:AGERE 制造商全稱:AGERE 功能描述:Low-Cost Ringing SLIC |
發布緊急采購，3分鐘左右您將得到回復。