- 您現在的位置：買賣IC網 > PDF目錄44998 > LTC694CN8-3.3#TRPBF (LINEAR TECHNOLOGY CORP) 1-CHANNEL POWER SUPPLY MANAGEMENT CKT, PDIP8 PDF資料下載
參數資料
| 型號： | LTC694CN8-3.3#TRPBF |
| 廠商： | LINEAR TECHNOLOGY CORP |
| 元件分類： | 電源管理 |
| 英文描述： | 1-CHANNEL POWER SUPPLY MANAGEMENT CKT, PDIP8 |
| 封裝： | 0.300 INCH, LEAD FREE, PLASTIC, DIP-8 |
| 文件頁數： | 20/20頁 |
| 文件大小： | 189K |
| 代理商： | LTC694CN8-3.3#TRPBF |
LTC694-3.3/LTC695-3.3
9
69453fb
APPLICATIONS INFORMATION
Microprocessor Reset
The LTC694-3.3/LTC695-3.3 use a bandgap voltage refer-
ence and a precision voltage comparator C1 to monitor the
3.3V supply input on VCC (see the Block Diagram). When
VCC falls below the reset voltage threshold, the RESET out-
put is forced to active low state. The reset voltage threshold
accounts for a 10% variation on VCC, so the RESET output
becomes active low when VCC falls below 3.0V (2.9V typi-
cal). On power-up, the RESET signal is held active low for a
minimum of 140ms after reset voltage threshold is reached
to allow the power supply and microprocessor to stabilize.
The reset active time is adjustable on the LTC695-3.3.
On power-down, the RESET signal remains active low
even with VCC as low as 1V. This capability helps hold the
microprocessor in stable shutdown condition. Figure 1
shows the timing diagram of the RESET signal.
The precision voltage comparator, C1, typically has 40mV
of hysteresis which ensures that glitches at VCC pin do
not activate the RESET output. Response time is typically
10ms. To help prevent mistriggering due to transient loads,
the VCC pin should be bypassed with a 0.1μF capacitor
with the leads trimmed as short as possible.
The LTC695-3.3 has two additional outputs: RESET and
LOW
_
LINE.RESETisanactivehighoutputandistheinverse
of RESET. LOW
_
LINE is the output of the precision voltage
comparator C1. When VCC falls below the reset voltage
threshold, LOW
_
LINE goes low. LOW
_
LINE returns high as
soon as VCC rises above the reset voltage threshold.
Battery Switchover
The battery switchover circuit compares VCC to the VBATT
input, and connects VOUT to whichever is higher. When
VCC rises to 70mV above VBATT, the battery switchover
comparator, C2, connects VOUT to VCC through a charge
pumped NMOS power switch, M1. When VCC falls to 50mV
above VBATT, C2 connects VOUT to VBATT through a PMOS
switch, M2. C2 has typically 20mV of hysteresis to prevent
spurious switching when VCCremainsnearlyequaltoVBATT.
The response time of C2 is approximately 20μs.
During normal operation, the LTC694-3.3/LTC695-3.3 use
a charge-pumped NMOS power switch to achieve low
dropout and low supply current. This power switch can
deliver up to 50mA to VOUT from VCC and has a typical on
resistance of 5Ω. The VOUT pin should be bypassed with
a capacitor of 0.1μF or greater to ensure stability. Use of
a larger bypass capacitor is advantageous for supplying
current to heavy transient loads.
When operating currents larger than 50mA are required
from VOUT, or a lower dropout (VCC – VOUT voltage dif-
ferential) is desired, the LTC695-3.3 should be used. This
product provides BATT ON output to drive the base of
an external PNP transistor (Figure 2). If higher currents
are needed with the LTC694-3.3, a high current Schottky
diode can be connected from the VCC pin to the VOUT pin
to supply the extra current.
VCC
t1
t1 = RESET ACTIVE TIME
V1 = RESET VOLTAGE THRESHOLD
V2 = RESET VOLTAGE THRESHOLD +
RESET THRESHOLD HYSTERESIS
t1
V2
V1
694/5-3.3 F01
RESET
LOW LINE
Figure 1. Reset Active Time
相關PDF資料 |
PDF描述 |
|---|---|
| LTC695CN-3.3#TRPBF | 1-CHANNEL POWER SUPPLY MANAGEMENT CKT, PDIP16 |
| LTC695IS | 4-CHANNEL POWER SUPPLY MANAGEMENT CKT, PDSO16 |
| LTC691IS | 4-CHANNEL POWER SUPPLY MANAGEMENT CKT, PDSO16 |
| LTC691CS | 4-CHANNEL POWER SUPPLY MANAGEMENT CKT, PDSO16 |
| LTC6992HDCB-2#TRPBF | 0.02 A SWITCHING CONTROLLER, PDSO6 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| LTC694CN8PBF | 制造商:LINER 制造商全稱:Linear Technology 功能描述:Microprocessor Supervisory Circuits |
| LTC694CN8-PBF | 制造商:LINER 制造商全稱:Linear Technology 功能描述:Microprocessor Supervisory Circuits |
| LTC694CS-3.3 | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Power Supply Supervisor |
| LTC694CS8 | 功能描述:IC MPU SUPERVISORY CIRCUIT 8SOIC RoHS:否 類別:集成電路 (IC) >> PMIC - 監控器 系列:- 標準包裝:1 系列:- 類型:簡單復位/加電復位 監視電壓數目:1 輸出:開路漏極或開路集電極 復位:高有效 復位超時:- 電壓 - 閥值:1.8V 工作溫度:-40°C ~ 125°C 安裝類型:表面貼裝 封裝/外殼:6-TSOP（0.059"，1.50mm 寬）5 引線 供應商設備封裝:5-TSOP 包裝:剪切帶 (CT) 其它名稱:NCP301HSN18T1GOSCT |
| LTC694CS8#PBF | 功能描述:IC MPU SUPERVISORY CIRCUIT 8SOIC RoHS:是 類別:集成電路 (IC) >> PMIC - 監控器 系列:- 其它有關文件:STM6905 View All Specifications 標準包裝:1 系列:- 類型:多壓監控器 監視電壓數目:5 輸出:開路漏極或開路集電極 復位:低有效 復位超時:最小為 140 ms 電壓 - 閥值:2.188V，2.955V，可調，可調，可調 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:8-TSSOP，8-MSOP（0.118"，3.00mm 寬） 供應商設備封裝:8-TSSOP 包裝:Digi-Reel® 產品目錄頁面:1197 (CN2011-ZH PDF) 其它名稱:497-8728-6 |
發布緊急采購，3分鐘左右您將得到回復。