- 您現在的位置：買賣IC網 > PDF目錄44997 > LTC4280IUFD (LINEAR TECHNOLOGY CORP) 1-CHANNEL POWER SUPPLY SUPPORT CKT, PQCC24 PDF資料下載
參數資料
| 型號： | LTC4280IUFD |
| 廠商： | LINEAR TECHNOLOGY CORP |
| 元件分類： | 電源管理 |
| 英文描述： | 1-CHANNEL POWER SUPPLY SUPPORT CKT, PQCC24 |
| 封裝： | 4 X 5 MM, PLASTIC, MO-220, QFN-24 |
| 文件頁數： | 27/28頁 |
| 文件大?。?/td> | 286K |
| 代理商： | LTC4280IUFD |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁當前第27頁第28頁
LTC4280
8
4280f
PIN FUNCTIONS
ADIN: ADC Input. A voltage between 0V and 1.235V
applied to this pin is measured by the onboard ADC. Tie
to ground if unused.
ADR0, ADR1, ADR2: Serial Bus Address Inputs. Tying
these pins to ground, to the INTVCC pin or open congures
one of 27 possible addresses. See Table 1 in Applications
Information.
ALERT: Fault Alert Output. Open-drain logic output that
is pulled to ground when a fault occurs to alert the host
controller. A fault alert is enabled by the ALERT register.
See Applications Information. Tie to ground if unused.
EN: Enable Input. Ground this pin to indicate a board is
present and enable the N-channel MOSFET to turn on. When
this pin is high, the MOSFET is not allowed to turn on. An
internal 10μA current source pulls up this pin. Transitions
on this pin are recorded in the Fault register. A high-to-low
transition activates the logic to read the state of the ON pin
and clear Faults. See Applications Information.
EXPOSED PAD (Pin 25): Exposed pad may be left open
or connected to device ground.
FB: Foldback Current Limit and Power Good Input. A
resistive divider from the output is tied to this pin. When
the voltage at this pin drops below 1.235V, power is not
considered good. The power bad condition may result in the
GPIO pin pulling low or going high impedance depending
on the conguration of control register bits A6 and A7.
Also a power bad fault is logged in this condition if the
LTC4280 has nished the start-up cycle and the GATE pin
is high. See Applications Information. The current limit
folds back from a 26mV sense voltage to 10mV as the
FB pin voltage falls from 0.6V to 0V.
FILTER: Fault Filter Input. Connect a capacitor between this
pin and ground to set a 123ms/μF delay for overcurrent
fault ltering after startup.
GATE: Gate Drive for External N-Channel MOSFET. An
internal 20μA current source charges the gate of the
MOSFET. Often no compensation capacitor is required
on the GATE pin, but a resistor and capacitor network
from this pin to ground may be used to set the turn-on
output voltage slew rate. See Applications Information.
During turn-off there is a 1mA pulldown current. During
a short-circuit or undervoltage lockout (VDD or INTVCC),
a 450mA pulldown current source between GATE and
SOURCE is activated.
GND: Device Ground.
GPIO: General Purpose Input/Output. Open-drain logic
output or logic input. Defaults to an output set to pull
low to indicate power is not good. Congure according
to Table 2 and 3.
INTVCC: Low Voltage Supply Decoupling Output. Connect
a 0.1μF capacitor from this pin to ground.
ON: On Control Input. A rising edge turns on the external
N-channel MOSFET and a falling edge turns it off. This pin
also congures the state of the FET On bit in the control
register (and hence the external MOSFET) at power up.
For example, if the ON pin is tied high, then the FET On bit
(A3 in Table 2) goes high 100ms after power-up. Likewise
if the ON pin is tied low then the part remains off after
power-up until the FET On bit is set high using the I2C
bus. A high-to-low transition on this pin clears the fault
register.
OV: Overvoltage Comparator Input. Connect this pin to an
external resistive divider from VDD. If the voltage at this
pin rises above 1.235V, an overvoltage fault is detected
and the GATE turns off. Tie to GND if unused.
相關PDF資料 |
PDF描述 |
|---|---|
| LTC4312IDE#TRPBF | 2-CHANNEL POWER SUPPLY SUPPORT CKT, PDSO14 |
| LTC4312CDE#PBF | 2-CHANNEL POWER SUPPLY SUPPORT CKT, PDSO14 |
| LTC4312IMS#TRPBF | 2-CHANNEL POWER SUPPLY SUPPORT CKT, PDSO16 |
| LTC4352CMS#PBF | 1-CHANNEL POWER SUPPLY MANAGEMENT CKT, PDSO12 |
| LTC4352CDD#TRPBF | 1-CHANNEL POWER SUPPLY MANAGEMENT CKT, PDSO12 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| LTC4280IUFD#PBF | 功能描述:IC HOT SWAP CONTROLLER 24-QFN RoHS:是 類別:集成電路 (IC) >> PMIC - 熱交換 系列:- 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:119 系列:- 類型:熱交換控制器 應用:通用型，PCI Express? 內部開關:無 電流限制:- 電源電壓:3.3V，12V 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:80-TQFP 供應商設備封裝:80-TQFP（12x12） 包裝:托盤 產品目錄頁面:1423 (CN2011-ZH PDF) |
| LTC4280IUFD#TRPBF | 功能描述:IC CTLR HOT SWAP I2C MON 24QFN RoHS:是 類別:集成電路 (IC) >> PMIC - 熱交換 系列:- 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:119 系列:- 類型:熱交換控制器 應用:通用型，PCI Express? 內部開關:無 電流限制:- 電源電壓:3.3V，12V 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:80-TQFP 供應商設備封裝:80-TQFP（12x12） 包裝:托盤 產品目錄頁面:1423 (CN2011-ZH PDF) |
| LTC4280IUFD-PBF | 制造商:LINER 制造商全稱:Linear Technology 功能描述:Hot Swap Controller with I2C Compatible Monitoring |
| LTC4280IUFD-TR | 制造商:LINER 制造商全稱:Linear Technology 功能描述:Hot Swap Controller with I2C Compatible Monitoring |
| LTC4280IUFD-TRPBF | 制造商:LINER 制造商全稱:Linear Technology 功能描述:Hot Swap Controller with I2C Compatible Monitoring |
發布緊急采購，3分鐘左右您將得到回復。