- 您現在的位置：買賣IC網 > Datasheet目錄42 > LTC4280CUFD#PBF (Linear Technology)IC CONTROLLER HOT SWAP QFN-24 Datasheet資料下載
參數資料
| 型號： | LTC4280CUFD#PBF |
| 廠商： | Linear Technology |
| 文件頁數： | 12/28頁 |
| 文件大?。?/td> | 291K |
| 描述： | IC CONTROLLER HOT SWAP QFN-24 |
| 標準包裝： | 73 |
| 類型： | 熱交換控制器 |
| 應用： | 通用 |
| 內部開關： | 無 |
| 電源電壓： | 2.9 V ~ 15 V |
| 工作溫度： | 0°C ~ 70°C |
| 安裝類型： | 表面貼裝 |
| 封裝/外殼： | 24-WFQFN 裸露焊盤 |
| 供應商設備封裝： | 24-QFN（5x4） |
| 包裝： | 管件 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁當前第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁
LTC4280
12
4280f
The LTC4280 is designed to turn a boards supply voltage
on and off in a controlled manner, allowing the board to be
safely inserted or removed from a live backplane. During
normal operation, the charge pump and gate driver turn
on an external N-channel MOSFETs gate to pass power to
the load. The gate driver uses a charge pump that derives
its power from the V
DD
pin. Also included in the gate driver
is an internal 6.5V gate-to-source clamp. During start-up
the inrush current is tightly controlled by using current
limit foldback and output dV/dt limiting.
The current sense (CS) ampli er monitors the load
current using the difference between the SENSE
+
and
SENSE
pin voltages. The CS ampli er limits the current
in the load by pulling back on the gate-to-source voltage
in an active control loop when the sense voltage exceeds
the commanded value. The CS ampli er requires 20糀
input bias current from both the SENSE
+
and the
SENSE
pins.
A short-circuit on the output to ground results in exces-
sive power dissipation during active current limiting. To
limit this power, the CS ampli er regulates the voltage
between the SENSE
+
and SENSE
pins at 26mV with
foldback to 10mV.
If an overcurrent condition persists, the internal circuit
breaker (CB) registers a fault when either the sense
voltage exceeds 25mV or the current sense ampli er
is in regulation for more than the time limit set by the
capacitor on the FILTER pin. This indicates to the logic
that it is time to turn off the GATE to prevent overheating.
At this point the start-up TIMER pin voltage ramps down
using the 2糀 current source until the voltage drops below
0.2V (comparator TM1) which tells the logic that the pass
transistor has cooled and it is safe to turn it on again if
overcurrent auto-retry is enabled. If the TIMER pin is tied
to INTV
CC
, the cool-down time defaults to 5 seconds on
an internal system timer in the logic.
The output voltage is monitored using the FB pin and the
Power Good (PG) comparator to determine if the power
is available for the load. The power good condition can be
signaled by the GPIO pin using an open-drain pulldown
transistor. The GPIO pin may also be con gured to signal
power bad, or as a general purpose input (GP comparator),
or a general purpose open drain output.
The Functional Diagram shows the monitoring blocks of
the LTC4280. The group of comparators on the left side
includes the undervoltage (UV), overvoltage (OV), reset
(RST), enable (EN) and signal on (ON) comparators. These
comparators determine if the external conditions are valid
prior to turning on the GATE. But rst the two undervoltage
lockout circuits, UVLO1 and UVLO2, validate the input
supply and the internally generated 3.1V supply, INTV
CC
.
UVLO2 also generates the power-up initialization to the
logic circuits as INTV
CC
crosses this rising threshold. If the
xed internal overvoltage comparator, OV2, detects that
V
DD
is greater than 15.6V, the part immediately generates
an overvoltage fault and turns the GATE off.
Included in the LTC4280 is an 8-bit A/D converter. The
converter has a 3-input multiplexer to select between the
ADIN pin, the SOURCE pin and the SENSE
+
SENSE
voltage.
An I
2
C interface is provided to read the A/D registers. It
also allows the host to poll the device and determine if
faults have occurred. If the ALERT line is con gured as an
interrupt, the host is enabled to respond to faults in real
time. The typical SDA line is divided into an SDAI (input)
and SDAO (output). This simpli es applications using an
optoisolator driven directly from the SDAO output. An
application which uses optoisolation is shown on the back
cover. The I
2
C device address is decoded using the ADR0,
ADR1 and ADR2 pins. These inputs have three states each
that decode into a total of 27 device addresses.
OPERATION
相關PDF資料 |
PDF描述 |
|---|---|
| LTC4300-1IMS8#TRPBF | IC HOTSWAP 2WIRE BUS BUFFR 8MSOP |
| LTC4300A-2IMS8#TRPBF | IC BUFFER BUS 2WR HOTSWAP 8-MSOP |
| LTC4301IDD | IC BUFFER BUS HOTSWAP 2WR 8DFN |
| LTC4301LIDD#TRPBF | IC BUFFER BUS HOTSWAP 2WR 8DFN |
| LTC4302IMS-1#TRPBF | IC BUFFER 2-WIRE BUS 10-MSOP |
相關代理商/技術參數 |
參數描述 |
|---|---|
| LTC4280CUFD-TR | 制造商:LINER 制造商全稱:Linear Technology 功能描述:Hot Swap Controller with I2C Compatible Monitoring |
| LTC4280CUFD-TRPBF | 制造商:LINER 制造商全稱:Linear Technology 功能描述:Hot Swap Controller with I2C Compatible Monitoring |
| LTC4280IUFD | 制造商:LINER 制造商全稱:Linear Technology 功能描述:Hot Swap Controller with I2C Compatible Monitoring |
| LTC4280IUFD#PBF | 功能描述:IC HOT SWAP CONTROLLER 24-QFN RoHS:是 類別:集成電路 (IC) >> PMIC - 熱交換 系列:- 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:119 系列:- 類型:熱交換控制器 應用:通用型，PCI Express? 內部開關:無 電流限制:- 電源電壓:3.3V，12V 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:80-TQFP 供應商設備封裝:80-TQFP（12x12） 包裝:托盤 產品目錄頁面:1423 (CN2011-ZH PDF) |
| LTC4280IUFD#TRPBF | 功能描述:IC CTLR HOT SWAP I2C MON 24QFN RoHS:是 類別:集成電路 (IC) >> PMIC - 熱交換 系列:- 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:119 系列:- 類型:熱交換控制器 應用:通用型，PCI Express? 內部開關:無 電流限制:- 電源電壓:3.3V，12V 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:80-TQFP 供應商設備封裝:80-TQFP（12x12） 包裝:托盤 產品目錄頁面:1423 (CN2011-ZH PDF) |
發布緊急采購，3分鐘左右您將得到回復。